Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type LH Side)
RM33K0E _58 Vehicle Interior _043553 SEAT _0227127 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type LH Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Seat Type LH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:
·
B394717

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



PROCEDURE

Hide 72620B 1.INSTALL REAR NO. 1 SEAT LOCK CABLE ASSEMBLY

a.
B403778C01
1.802,0.667 2.083,0.667 true 1.594,0.583 1.802,0.771 0.208,0.188 10 true *1
*1 Cable End
V113147

Install in this Direction


Turn the cable end in the installation direction shown in the illustration to install the cable end.


b.

Attach the casing cap.

HINT:

Install at the gray casing cap side.



c.
B411122C01
1.688,0.708 1.865,0.917 false 2.271,1.313 2.229,1.708 false 1.552,0.552 1.865,0.75 0.313,0.198 10 false *1 2.198,1.115 2.51,1.313 0.313,0.198 10 false *2
*1 Wiring Harness Clamp A
*2 Joint Case


Attach the 3 wiring harness clamps to install the rear No. 1 seat lock cable assembly.

HINT:
·

Secure wiring harness clamp A to the vertical wire of the seat cushion.


·

Secure the joint case between the wires.




Hide 78920B 2.INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY LH

a.
B403779C01
2.792,2.323 2.594,2.021 true 2.448,1.885 2.76,2.083 0.313,0.198 10 false *1
*1 Cable End
V113147

Install in this Direction


Turn the cable end in the installation direction shown in the illustration to install the cable end.


b.

Attach the casing cap and install No. 1 fold seat lock control cable assembly LH.


Hide 78950 3.INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY

a.
B403780C01
0,0 0,0 false
V113147

Install in this Direction


Pass the No. 1 fold seat stopper band assembly through itself to install it as shown in the illustration.


Hide 79104 4.INSTALL NO. 1 SEATBACK FRAME SUB-ASSEMBLY LH

a.
B403773

Install the No. 1 seatback frame sub-assembly LH with 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.
B410988C01
2.656,1.396 2.135,1.375 true 2.625,0.802 2.698,0.417 true 2.656,0.25 2.917,0.479 0.26,0.229 10 true *1 2.698,1.313 2.958,1.542 0.26,0.229 10 true *2
*1 Side Frame
*2 Pipe
V113147

Install in this Direction


Pass the rear No. 1 seat lock cable assembly through as shown in the illustration.

HINT:
·

Pass it through the hole in the side frame.


·

Pass it under the pipe.




c.
B403781C01
0.344,1.563 0.583,1.396 true 0.188,1.531 0.427,1.76 0.24,0.229 10 false *1
*1 Cable End
V113147

Install in this Direction


Turn the cable end in the installation direction shown in the illustration to install the cable end.


d.

Attach the casing cap.

HINT:

Install at the gray casing cap side.



Hide 72666B 5.INSTALL REAR SEAT LOCK COVER LH

a.
B404971

Attach the claw and guide to install the rear seat lock cover LH.


Hide 71879C 6.INSTALL REAR SEAT INNER RECLINING COVER LH

a.
B410989C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the rear seat inner reclining cover LH.


Hide 71878B 7.INSTALL REAR SEAT INNER RECLINING COVER RH

a.
B403770

Attach the guide.


b.

Install the rear seat inner reclining cover RH with screw.


Hide 71879B 8.INSTALL REAR SEAT INNER RECLINING COVER LH

a.
B403769

Attach the claw to install the rear seat inner reclining cover LH.


Hide 71878A 9.INSTALL REAR SEAT INNER RECLINING COVER RH

a.
B403768

Attach the claw and guide to install the rear seat inner reclining cover RH.


Hide 71876 10.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.
B403767

Attach the claw and guide to install the reclining adjuster inside cover LH.


Hide 71875B 11.INSTALL RECLINING ADJUSTER INSIDE COVER RH

a.
B403766

Attach the claw and guide to install the reclining adjuster inside cover RH.


Hide 12.INSTALL SEAT COVER WIRE

a.
B403765N02
1.313,1.385 1.615,1.51 true 2.563,1.552 3.073,1.375 true 1.292,0.354 1.594,0.479 true 2.573,0.521 3.083,0.344 true 2.031,1.313 2.031,1.542 true 2.031,0.75 2.031,0.979 true 1.146,0.24 1.302,0.438 0.156,0.198 10 true A 3.125,0.208 3.281,0.406 0.156,0.198 10 true A 1.156,1.313 1.313,1.51 0.156,0.198 10 true C 3.125,1.281 3.281,1.479 0.156,0.198 10 true C 1.979,0.552 2.135,0.75 0.156,0.198 10 true B 1.979,1.125 2.135,1.323 0.156,0.198 10 true B

Install the seat cover wire.

HINT:
·

Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.


·

Make sure to read the precautions before preparing the wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



Length:
A 130 mm (5.12 in.)
B 270 mm (10.63 in.)
C 290 mm (11.42 in.)

HINT:
B376752

The dimensions shown in the illustration are the lengths.



Hide 79012 13.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY LH

HINT:
·

When installing the No. 1 seat cushion cover sub-assembly LH, refer to the precautions in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION


·

Align the seam allowance in a single direction as shown in the illustration.

B404908N01
0.49,0.385 0.646,0.583 0.156,0.198 10 true A 0.802,0.438 0.958,0.635 0.156,0.198 10 true A 1.885,0.802 2.042,1 0.156,0.198 10 true B 2.188,0.927 2.344,1.125 0.156,0.198 10 true B 2.729,0.26 3.188,0.458 0.458,0.198 10 false A-A 5.177,0.25 5.635,0.448 0.458,0.198 10 false B-B



a.

Set the No. 1 seat cushion cover sub-assembly LH.


b.
B403784C01
2.083,2.083 2.26,1.927 true 1.906,1.188 2.073,0.938 true 2.25,1.219 2.083,0.938 true 2.094,2.073 1.906,1.938 true 1.031,0.813 1.469,0.781 true 2.698,0.771 3.073,0.833 true 2.698,1.448 3.073,1.51 true 2.698,1.979 3.104,2.104 true 1.042,1.49 1.448,1.625 true 1.042,0.823 1.469,1.01 true 1.042,1.479 1.479,1.448 true 1.083,2.073 1.469,1.979 true 2.708,1.01 3.083,0.844 true 2.708,1.667 3.083,1.5 true 1.167,3.281 1.344,3.323 true 1.896,3.99 2.104,4.365 true 1.99,2.115 2.188,2.302 0.198,0.188 10 true (1) 2,0.729 2.198,0.917 0.198,0.188 10 true (1) 0.823,0.729 1.021,0.917 0.198,0.188 10 true (2) 0.833,1.406 1.031,1.594 0.198,0.188 10 true (2) 0.844,1.969 1.042,2.156 0.198,0.188 10 true (2) 3.135,0.75 3.333,0.938 0.198,0.188 10 true (2) 3.146,1.438 3.344,1.625 0.198,0.188 10 true (2) 3.146,2.01 3.344,2.198 0.198,0.188 10 true (2) 2.115,4.385 2.427,4.583 0.313,0.198 10 false *1 1.354,3.24 1.667,3.438 0.313,0.198 10 false *a
*1 Hog Ring Pliers
*a Cutout


Using hog ring pliers, install the No. 1 seat cushion cover sub-assembly LH to the No. 1 seat cushion pad LH with 14 new hog rings in the order indicated in the illustration.

NOTICE:
·

Be careful not to damage the No. 1 seat cushion cover sub-assembly LH.


·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seat cushion cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.



c.
B403785C01
2.052,4.281 1.854,3.99 false 2,4.333 2.26,4.552 0.26,0.219 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, connect the 3 straps of the No. 1 seat cushion cover sub-assembly LH to the No. 1 seat cushion pad LH with 3 new hog rings.

NOTICE:
·

Be careful not to damage the No. 1 seat cushion cover sub-assembly LH.


·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seat cushion cover sub-assembly LH.




Hide 14.INSTALL SEAT CUSHION COVER WITH PAD

a.
B403786C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in installation direction (1) shown in the illustration to temporarily install the seat cushion cover with pad.


b.

Install the seat cushion cover with pad in the installation direction (2) so that the rear end is held in place.


c.
B410987

Move the No. 1 seatback frame sub-assembly LH in the direction indicated by the arrow shown in the illustration.


d.
B403760

While sliding the part in the direction indicated by the arrow shown in the illustration, install the J hook.


Hide 73330C 15.INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY RH

Hide 73340C 16.INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY LH

Hide 72170 17.INSTALL REAR SEAT OUTER TRACK ASSEMBLY LH

a.
B404890

Temporarily install the rear seat outer track assembly LH with the 2 bolts until it contacts the part.


b.
B403754C01
0,0 0,0 false
V113147

Install in this Direction


Slide the rail and install the rear seat outer track assembly LH with the bolt as shown in the illustration.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 72190 18.INSTALL REAR SEAT INNER TRACK ASSEMBLY LH

a.
B404895

Temporarily install the rear seat inner track assembly LH with the 2 bolts until it contacts the part.


b.
B403753C01
0,0 0,0 false
V113147

Install in this Direction


Slide the rail and install the rear seat inner track assembly LH with the bolt as shown in the illustration.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 72201D 19.INSTALL SEAT TRACK HANDLE SUB-ASSEMBLY LH

a.

Push in the seat track handle sub-assembly LH to attach the lock spring and install the seat track handle sub-assembly as shown in the illustration.

B404881C01
4.948,1.313 4.698,1.104 true 2.281,1.344 2.49,1.115 true 2.219,0.896 2.281,0.365 true 0.406,0.792 0.365,0.313 true 5.073,0.844 5.052,0.365 true 6.74,0.813 6.698,0.333 true 0.25,0.094 0.563,0.292 0.313,0.198 10 false *1 2.24,0.208 2.552,0.406 0.313,0.198 10 false *1 4.99,0.177 5.302,0.375 0.313,0.198 10 false *1 6.604,0.146 6.917,0.344 0.313,0.198 10 false *1 5.031,1.313 5.344,1.51 0.313,0.198 10 false *2 2.063,1.292 2.375,1.49 0.313,0.198 10 false *2
*1 Seat Track Handle Sub-Assembly LH *2 Lock Spring
V113147

Install in this Direction - -



b.
B403752

Slide the rear seat inner track assembly LH and rear seat outer track assembly in the direction indicated by the arrow shown in the illustration and install them with the 4 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


c.
B403747

Attach the claw.


Hide 72660F 20.INSTALL REAR SEAT LOCK ASSEMBLY LH

a.
B403746

Using a T55 "TORX" socket wrench, install the 2 "TORX" bolts and rear seat lock assembly LH.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


b.
B411842C01
0.969,1.094 0.635,0.604 true 0.5,0.417 0.813,0.615 0.313,0.198 10 false *1
*1 Cable End
V113147

Install in this Direction


Turn the cable end in the installation direction shown in the illustration to install the cable end.


c.

Attach the casing cap.

HINT:

Install at the purple casing cap side.



Hide 72660F 21.INSTALL REAR SEAT LOCK ASSEMBLY LH

a.
B402798

Using a T55 "TORX" socket wrench, install the 2 "TORX" bolts and rear seat lock assembly LH.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


b.

Attach the hook.


c.
B404898C01
0.521,0.583 0.844,1.073 true 0.375,0.365 0.594,0.552 0.219,0.188 10 true *1
*1 Cable End
V113147

Install in this Direction


Turn the cable end in the installation direction shown in the illustration to install the cable end.


d.

Attach the casing cap.

HINT:

Install at the yellow casing cap side.



Hide 79106 22.INSTALL NO. 1 SEAT LEG SUB-ASSEMBLY LH

a.
B402796

Install the No. 1 seat leg sub-assembly LH with 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 72666B 23.INSTALL REAR SEAT LOCK COVER LH

a.
B402795

Attach the guide.


b.

Attach the clip to install the rear seat lock cover LH.


Hide 72666B 24.INSTALL REAR SEAT LOCK COVER LH

a.
B402794

Attach the guide.


b.

Attach the clip to install the rear seat lock cover LH.


Hide 72618 25.INSTALL REAR SEATBACK LOCK STRIKER PROTECTOR

a.
B402793

Attach the claw and clip to install the rear seatback lock striker protector.


Hide 72616A 26.INSTALL REAR SEATBACK LOCK STRIKER COVER LH

a.
B421279

w/ Seat Belt Warning System:

Attach the clamp.


b.
B402792

Attach the claw and clip to install the rear seatback lock striker cover LH.


Hide 72618 27.INSTALL REAR SEATBACK LOCK STRIKER PROTECTOR

a.
B402791

Attach the claw and clip to install the rear seatback lock striker protector.


Hide 72616A 28.INSTALL REAR SEATBACK LOCK STRIKER COVER LH

a.
B402790

Attach the claw and clip to install the rear seatback lock striker cover LH.


b.
B403761

Move the No. 1 seatback frame sub-assembly LH in the direction indicated by the arrow shown in the illustration.


Hide 29.INSTALL SEAT COVER WIRE

a.
B402788N02
3.146,1.094 2.552,1.167 true 1.677,1.198 0.99,1.125 true 2.104,0.948 2.104,0.698 true 2.063,0.49 2.219,0.688 0.156,0.198 10 true A 0.813,1.042 0.969,1.24 0.156,0.198 10 true B 3.24,1.031 3.396,1.229 0.156,0.198 10 true B

Install the seat cover wire.

HINT:
·

Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.


·

Make sure to read the precautions before preparing the wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



Length:
A 270 mm (10.63 in.)
B 290 mm (11.42 in.)


HINT:
B376752

The dimensions shown in the illustration are the lengths.



Hide 79014 30.INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY LH

HINT:
·

When installing the No. 1 seatback cover sub-assembly LH, refer to the precautions in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION


·

Align the seam allowance in a single direction as shown in the illustration.

B404909N01
0.229,0.167 0.375,0.354 0.146,0.188 10 true A 0.458,0.229 0.604,0.417 0.146,0.188 10 true A 1.063,0.375 1.208,0.563 0.146,0.188 10 true C 1.281,0.438 1.427,0.625 0.146,0.188 10 true C 2.063,0.5 2.208,0.688 0.146,0.188 10 true B 2.042,0.76 2.188,0.948 0.146,0.188 10 true B 2.833,0.208 3.292,0.406 0.458,0.198 10 false A-A 4.292,0.229 4.75,0.427 0.458,0.198 10 false B-B 5.74,0.219 6.198,0.417 0.458,0.198 10 false C-C



a.

Set the No. 1 seatback cover sub-assembly LH.


b.
B404899C01
1.177,3.281 1.344,3.302 true 1.885,4 1.833,4.313 true 2.115,0.792 1.927,1.094 true 2.104,0.792 2.281,1.115 true 2.667,1.698 3.083,1.583 true 2.677,1.438 3.094,1.583 true 1.052,1.563 1.531,1.438 true 1.052,1.552 1.563,1.708 true 1.75,4.333 2.063,4.531 0.313,0.198 10 false *1 1.344,3.198 1.656,3.396 0.313,0.198 10 false *a 2.031,0.604 2.24,0.802 0.208,0.198 10 true (1) 0.833,1.479 1.042,1.677 0.208,0.198 10 true (2) 3.115,1.5 3.323,1.698 0.208,0.198 10 true (2)
*1 Hog Ring Pliers
*a Cutout


Using hog ring pliers, install the No. 1 seatback cover sub-assembly LH to the No. 1 seatback pad LH with 6 new hog rings in the order indicated in the illustration.

NOTICE:
·

Be careful not to damage the No. 1 seatback cover sub-assembly LH.


·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.



HINT:

Install the hog rings at the cutouts if they are there.



c.
B404900C01
2.021,4.323 1.875,3.979 false 1.958,4.417 2.271,4.615 0.313,0.198 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, connect the 3 straps of the No. 1 seatback cover sub-assembly LH to the No. 1 seatback pad LH with 6 new hog rings.

NOTICE:
·

Be careful not to damage the No. 1 seatback cover sub-assembly LH.


·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the No. 1 seatback cover sub-assembly LH.




Hide 31.INSTALL SEATBACK COVER WITH PAD

a.
B404901C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)
V113149

Install in this Direction (3)


While aligning the top, push in the seatback cover with pad in the installation direction (1).


b.

Push in the bottom left side of the seatback cover with pad in the installation direction (2).


c.

Pass the installation part of the rear seat center armrest assembly shown by the arrow through the slit.


d.

Push in the bottom right side of the seatback cover with pad in the installation direction (3).


e.
B402783

While sliding the part in the direction indicated by the arrow shown in the illustration, install the J hook.


Hide 71931B 32.INSTALL REAR SEAT NO. 1 HEADREST SUPPORT ASSEMBLY

a.
B410994C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the claw and install the 4 rear seat No. 1 headrest support assemblies.


b.
B411843C01
0,0 0,0 false
V113147

Install in this Direction


Close the fasteners as shown in the illustration.


c.

Push in the fasteners as shown in the illustration.

B411844C01
0,0 0,0 false
V113147

Install in this Direction - -



d.
B402780

While sliding the part in the direction indicated by the arrow shown in the illustration, attach the J hook.


Hide 72830 33.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY

a.
B402779

Set the plate.


b.

While pushing the plate in the installation direction (1), attach the guide.

B411123C01
0.448,2.031 0.594,1.313 true 1.802,2.031 1.979,1.458 true 1.719,2.083 1.948,2.281 0.229,0.198 10 true *1 0.354,2.083 0.583,2.281 0.229,0.198 10 true *1
*1 Stopper Pin - -
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)



c.

While aligning the stopper pin position of the rear seat center armrest assembly, install the plate in the installation direction (2).


d.

Install the rear seat center armrest assembly with bolt.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)


Hide 71844E 34.INSTALL REAR SEAT RECLINING COVER LH

a.
B404905C01
0,0 0,0 false
V113147

Install in this Direction


Push the rear seat reclining cover LH as shown in the illustration to attach the claw and install the rear seat reclining cover LH.


Hide 71844D 35.INSTALL REAR SEAT RECLINING COVER LH

a.
B404907

Attach the claw and guide.


b.

Install the rear seat reclining cover LH with screw.


Hide 72526E 36.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.
B410995C01
1.896,1.688 2.688,1.552 true 2.75,1.448 3.063,1.646 0.313,0.198 10 false *1
*1 Snap Ring
V113147

Install in this Direction


Install the snap ring to the reclining adjuster release handle LH.


b.

Push the reclining adjuster release handle LH as shown in the illustration to attach the guide and install the reclining adjuster release handle LH.


Hide 71940A 37.INSTALL REAR SEAT HEADREST ASSEMBLY

a.
B411002C01
0,0 0,0 false
V100136

Apply Silicon


Apply silicon lubricant in this range.


b.

Install rear seat headrest assembly.


Hide 71960B 38.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY

a.
B410983C01
0,0 0,0 false
V100136

Apply Silicon


Apply silicon lubricant in this range.


b.

Install rear seat center headrest assembly.