Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY
RM33K0E _58 Vehicle Interior _043553 SEAT _0227129 REAR NO. 2 SEAT ASSEMBLY A

SEAT  REAR NO. 2 SEAT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:
·
B394717

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 79204A 1.INSTALL NO. 2 SEATBACK FRAME SUB-ASSEMBLY LH

a.
B439035C02
0.083,0.083 0.333,0.25 0.25,0.167 10 true *A 0.083,2.25 0.333,2.417 0.25,0.167 10 true *B
*A for LH side
*B for RH side


Using a T55 "TORX" socket wrench, install the 4 "TORX" bolts and rear No. 2 seat hinge sub-assembly LH.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 71304B 2.INSTALL REAR NO. 2 SEAT HINGE SUB-ASSEMBLY LH

a.
B439037C01
1.99,1.281 1.729,0.948 true 2.188,3.188 2.115,3.031 true 0.917,1 1.552,0.813 true 0.552,2.656 0.75,2.813 true 0.375,3.01 0.573,3.167 true 0.594,1.385 1.198,1.615 true 1.688,2.917 1.885,3.073 true 1.948,1.292 2.26,1.448 0.313,0.156 10 false *1 0.719,0.938 0.906,1.135 0.188,0.198 10 false *2 0.198,2.844 0.51,3 0.313,0.156 10 false *3 2.156,3.198 2.469,3.354 0.313,0.156 10 false *1 0.354,2.552 0.542,2.75 0.188,0.198 10 false *2 0.385,1.281 0.583,1.458 0.198,0.177 10 false *3 1.51,2.75 1.823,2.906 0.313,0.156 10 false *3
*1 Spring A
*2 Spring B
*3 Bracket
V100136

Apply Grease
V113147

Install in this Direction


Apply grease to the position shown in the illustration.


b.

Set spring A to the lower part of the bracket.


c.

Set spring B to the upper part of the bracket.


d.

While pushing in the installation direction shown in the illustration, align the position of the bolt installation holes.

NOTICE:

Install the spring carefully, as it is under tension.



e.

Install the rear No. 2 seat hinge sub-assembly LH with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 71692B 3.INSTALL REAR OUTER SEAT LOCK COVER LH

a.
B439038C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in the installation direction (1) shown in the illustration to temporarily install the rear outer seat lock cover LH.


b.

Push the rear outer seat lock cover LH in the installation direction (2) shown in the illustration to attach the guide and install the rear outer seat lock cover LH.


Hide 72695C 4.INSTALL REAR SEAT LOCK CONTROL CABLE LH

a.
B439039C01
0.448,2.323 0.823,2.594 true 0.865,2.604 1.063,2.802 0.198,0.198 10 true *1
*1 Cable End
V113147

Install in this Direction


Turn the cable end in the install direction shown in the illustration and connect the cable end to install the rear seat lock control cable LH.

HINT:

Pass the rear seat lock control cable LH through the hole in the leg frame.



b.

Attach the casing cap.

HINT:

Install at the yellow casing cap side.



c.
B439031

Attach the clamp.


Hide 79236A 5.INSTALL NO. 2 SEAT LEG COVER

a.
B439040C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in the installation direction (1) shown in the illustration to attach the claw.


b.

While pushing the plate in the installation direction (2), attach the guide.


c.

Attach the clip to install the No. 2 seat leg cover.


Hide 79040B 6.INSTALL REAR NO. 2 SEAT LEG ASSEMBLY LH

a.
B439041C01
0.365,0.917 0.219,0.594 true 1.531,0.844 1.677,0.448 true 0.104,0.375 0.417,0.531 0.313,0.156 10 false *A 1.646,0.26 1.958,0.417 0.313,0.156 10 false *B
*A Installation Position A
*B Installation Position B


Install the 2 bolts and rear No. 2 seat leg assembly LH.


b.

Move a screwdriver with its tip wrapped with protective tape in the direction indicated by the arrow to widen the spring and install the hook part.


c.

Temporarily install the rear seat lock control cable LH along the No. 2 seat cushion frame sub-assembly LH.

HINT:
·

At installation position A, pass the cable below the pipe.


·

At installation position B, pass the cable above the pipe.




d.
B439042C01
2.781,2.469 3.01,2.594 true 3.031,2.531 3.24,2.719 0.208,0.188 10 false *1
*1 Cable End
V113147

Install in this Direction


for LH side:

i.

Turn the cable end in the install direction shown in the illustration and connect the cable end.


ii.

Attach the casing cap.

HINT:

Install at the purple casing cap side.




e.
B439043C01
0.823,2.594 0.729,2.229 true 0.771,2.615 0.969,2.792 0.198,0.177 10 true *1
*1 Cable End
V113147

Install in this Direction


for RH side:

i.

Turn the cable end in the install direction shown in the illustration and connect the cable end.


ii.

Attach the casing cap.

HINT:

Install at the natural casing cap side.




f.
B439044C01
0.313,1.313 0.313,0.583 true 1.771,0.771 1.771,0.302 true 2.531,1.688 3,1.125 true 0.229,0.417 0.542,0.573 0.313,0.156 10 false *A 1.698,0.135 2.01,0.292 0.313,0.156 10 false *B 3.021,1 3.333,1.156 0.313,0.156 10 false *C
*A Installation Position A
*B Installation Position B
*C Installation Position C


Attach the 3 wiring harness clamps.

HINT:
·

At installation position A, align the marking of the cable joint.


·

At installation position B, secure at the white positioning tape of the cable.


·

At installation position C, align and secure at the curved end of the pipe.




g.
B439045C01
0,0 0,0 false
V100136

MP Grease


Apply grease to both ends of the spring.


h.

Install the spring to the No. 2 seat leg assembly LH.

HINT:

Install the spring facing the same direction shown in the illustration.



Hide 73580A 7.INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY

Hide 79225B 8.INSTALL REAR NO. 2 SEAT CUSHION CARPET LH

a.
B439046C01
0,0 0,0 false
V113147

Install in this Direction


Move the rear No. 2 seat leg assembly LH as shown in the illustration.


b.

Attach the clip and install the rear No. 2 seat cushion carpet LH.


Hide 71694 9.INSTALL REAR SEAT LOWER CUSHION HINGE COVER LH

a.
B439047C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


While rotating the part in install direction (1) shown in the illustration attach the claw.


b.

While rotating the part in install direction (2) shown in the illustration, attach the claw to rear seat lower cushion hinge cover LH.


Hide 10.INSTALL SEAT COVER WIRE

a.
B439022N01
1.917,0.594 2.333,0.177 true 2.708,1.427 1.906,1.031 true 0.656,1.74 1.302,1.156 true 1.313,0.75 0.875,0.385 true 2.74,1.354 2.896,1.552 0.156,0.198 10 false A 0.698,0.281 0.854,0.479 0.156,0.198 10 false A 2.365,0.063 2.521,0.26 0.156,0.198 10 false B 0.552,1.76 0.708,1.958 0.156,0.198 10 false B

Install the seat cover wire.

HINT:
·

There are service parts available for wires of 1000 mm or longer and formed wires.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm supplied wire into the dimensions shown in the illustration.


·

Refer to the precautions when creating a wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



Length:
A 270 mm (10.63 in.)
B 200 mm (7.88 in.)


HINT:
B376752

The dimensions shown in the illustration are the length.



Hide 79022 11.INSTALL NO. 2 CUSHION COVER SUB-ASSEMBLY LH

HINT:
·

Refer to the precautions on wrinkles to avoid creating any on the No. 2 cushion cover sub-assembly LH when installing the seat cover.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION


·

As shown in the illustration, fix all of the cover seam allowances in the same direction.

B439048N01
0.458,1.563 0.615,1.76 0.156,0.198 10 false A 0.698,1.448 0.854,1.646 0.156,0.198 10 false A 1.771,0.854 1.927,1.052 0.156,0.198 10 false B 1.552,0.969 1.708,1.167 0.156,0.198 10 false B 3.375,0.885 4.146,1.083 0.771,0.198 10 false A - A 5.365,0.885 6.135,1.083 0.771,0.198 10 false B - B



a.

Temporarily install the No. 2 cushion cover sub-assembly LH to the No. 2 seat cushion pad LH.


b.

Using hog ring pliers, install the No. 2 cushion cover sub-assembly LH to the No. 2 seat cushion pad LH with 8 new hog rings in the order shown in the illustration.

B439049C01
4.958,1.344 5.01,1.563 false 4.635,0.604 4.833,0.604 true 2.646,0.802 3.083,1.333 true 2.417,0.948 3.083,1.333 true 1.583,0.25 2.083,0.5 true 1.583,0.25 1.833,0.75 true 2.417,0.417 3.083,0.167 true 2.583,0.5 3.083,0.167 true 1.333,1.25 2,1 true 1.333,1.25 1.833,0.917 true 4.969,1.573 5.281,1.729 0.313,0.156 10 false *1 4.844,0.51 5.031,0.708 0.188,0.198 10 false *a 3.104,1.333 3.563,1.531 0.458,0.198 10 false (1) 1.375,0.094 1.604,0.302 0.229,0.208 10 false (1) 1.188,1.26 1.438,1.49 0.25,0.229 10 false (2) 3.115,0.021 3.573,0.219 0.458,0.198 10 false (2)
*1 Hog Ring Pliers - -
*a Cutout - -



c.

Using hog ring pliers, connect the 2 straps of the No. 2 cushion cover sub-assembly LH to the No. 2 seat cushion pad LH with 6 new hog rings.

HINT:
·

Do not dirty or damage the No. 2 cushion cover sub-assembly LH.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and No. 2 seat cushion pad LH.



B439050C01
5,1.167 4.979,1.51 false 4.917,1.531 5.229,1.688 0.313,0.156 10 false *1
*1 Hog Ring Pliers - -



Hide 12.INSTALL SEAT CUSHION COVER WITH PAD

a.
B439051C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in the front of the seat cushion cover with pad in the installation direction (1).


b.

While slightly pulling up both sides of the seat cushion cover with pad, push them in the installation direction (2) shown in the illustration.


Hide 79378B 13.INSTALL NO. 3 SEAT CUSHION HINGE COVER LH

a.
B439052C01
0,0 0,0 false
V113147

Install in this Direction


While aligning the guide and claw, push them in as shown in the illustration.


b.

Attach the clip to install the No. 3 seat cushion hinge cover LH.


Hide 72066A 14.INSTALL REAR SEAT CUSHION LOCK HOOK SUB-ASSEMBLY LH

a.
B439053C01
0,0 0,0 false
V113147

Install in this Direction


Pass the rear seat cushion lock hook sub-assembly LH through the hole of the No. 2 seat cushion cover as shown in the illustration.


b.
B439054C01
0,0 0,0 false
V113147

Install in this Direction


Pass the rear seat cushion lock hook sub-assembly LH between the wire of the No. 2 seat cushion frame sub-assembly LH as shown in the illustration.


c.
B439055

Pass a cable tie through the loop at the end of the rear seat cushion lock hook sub-assembly LH and bind the top and bottom of the rear seat cushion lock hook sub-assembly.


d.
B439056C01
0,0 0,0 false
V113147

Install in this Direction


Pull to install the rear seat cushion lock hook sub-assembly LH as shown in the illustration.


e.

Cut the cable tie at the cross-hatched part.


Hide 79952 15.INSTALL NO. 2 SEAT CUSHION COVER

a.
B439016C02
0.083,0.094 0.396,0.25 0.313,0.156 10 false *A
*A for Rear Side


Set the No. 2 seat cushion cover to the No. 2 seat cushion frame sub-assembly LH.


b.

Install the 2 screws.


c.
B439015C02
0.083,0.094 0.396,0.25 0.313,0.156 10 false *A
*A for Front Side


Install the 2 screws.


d.
B439014

Install the screw.


e.
B439013

While sliding the part in the direction indicated by the arrow shown in the illustration to attach the J hook.


f.

Install the clip to No. 2 seat cushion cover.


g.
B439057

Push in the rear seat cushion lock hook sub-assembly LH the rear end of the seat cushion with pad.


Hide 16.INSTALL SEAT COVER WIRE

a.
B439011N01
2.635,1.302 1.646,0.854 true 2.667,1.219 2.823,1.417 0.156,0.198 10 false A

Install the seat cover wire.

HINT:
·

There are service parts available for wires of 1000 mm or longer and formed wires.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm supplied wire into the dimensions shown in the illustration.


·

Refer to the precautions when creating a wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



Length:
A 270 mm (10.63 in.)


HINT:
B376752

The dimensions shown in the illustration are the length.



Hide 79024 17.INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY LH

HINT:
·

Refer to the precautions on wrinkles to avoid creating any on the No. 2 seatback cover sub-assembly LH when installing the seat cover.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION


·

As shown in the illustration, fix all of the cover seam allowances in the same direction.

B439058N01
0.448,1.021 0.604,1.219 0.156,0.198 10 true A 0.708,0.938 0.865,1.135 0.156,0.198 10 false A 0.281,0.188 0.438,0.385 0.156,0.198 10 false B 0.469,0.448 0.625,0.646 0.156,0.198 10 false B 1.26,0.729 1.417,0.927 0.156,0.198 10 false C 1.521,0.646 1.677,0.844 0.156,0.198 10 false C 2.823,0.302 3.594,0.5 0.771,0.198 10 false A - A 4.104,0.292 4.875,0.49 0.771,0.198 10 false B - B 5.792,0.292 6.563,0.49 0.771,0.198 10 false C - C



a.

Set the No. 2 seatback cover sub-assembly LH.


b.

Using hog ring pliers, install the No. 2 seatback cover sub-assembly LH with 3 new hog rings.

HINT:
·

Do not dirty or damage the No. 2 seatback cover sub-assembly LH.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and No. 2 seatback pad LH.


B439059C01
5.177,1.552 5.104,1.354 false 4.927,0.615 4.75,0.615 true 5.125,1.563 5.438,1.719 0.313,0.156 10 false *1 4.938,0.531 5.25,0.688 0.313,0.156 10 false *a
*1 Hog Ring Pliers - -
*a Cutout - -




Hide 18.INSTALL SEATBACK COVER WITH PAD

a.
B439060C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push the seatback cover with pad in the installation direction (1) shown in the illustration.


b.

Push the bottom part of the seatback cover with pad in the installation direction (2) to install the seatback cover with pad.


Hide 71931C 19.INSTALL REAR NO. 2 SEAT HEADREST SUPPORT ASSEMBLY

a.
B439061C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw and push in the install direction shown in the illustration to install the 2 rear No. 2 seat headrest support assemblies.


b.
B439007

While sliding the part in the direction indicated by the arrow shown in the illustration to attach the J hook.


Hide 79393 20.INSTALL REAR NO. 2 SEATBACK CUSHION

a.
B439006

Install the screw and rear No. 2 seatback cushion.


Hide 71844A 21.INSTALL REAR NO. 2 SEAT RECLINING COVER LH

a.
B439062C01
0,0 0,0 false
V113147

Install in this Direction


Pass the rear No. 2 seat reclining cover LH through the installation part of the reclining adjuster release handle LH and push to attach the claw and guide as shown in the illustration.


b.

Install the screw.


c.
B439004

Install the screw to rear No. 2 seat reclining cover LH.


Hide 72526E 22.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.
B439063C01
0,0 0,0 false
V113147

Install in this Direction


While pulling up in the direction of the arrow, push as shown in the illustration to attach the claw and install the reclining adjuster release handle LH.


Hide 72526C 23.INSTALL NO. 2 RECLINING ADJUSTER RELEASE HANDLE LH

a.
B439064C01
2.583,3.833 3.083,2.75 true 3.083,2.75 2.667,1.833 true 1.25,2.833 1.75,2.333 true 1.5,3.25 1.25,2.833 true 0.917,4.25 1.135,3.906 true 1.74,4.406 1.885,4.063 true 1.052,2.75 1.229,2.958 0.177,0.208 10 false *1 1.677,4.417 1.99,4.573 0.313,0.156 10 false *2 0.844,4.26 1.156,4.417 0.313,0.156 10 false *3 3.104,2.667 3.417,2.823 0.313,0.156 10 false *a
*1 No. 2 Seat Cushion Frame Sub-Assembly LH
*2 Rear Seat Lower Cushion Hinge Cover LH
*3 Rear Seatback Lock Release Button
*a Resin portion of link
V113147

Install in this Direction


Pull the No. 2 reclining adjuster release handle LH in the direction of the cushion wire part of the No. 2 seat cushion frame sub-assembly LH as shown in the illustration to install the No. 2 reclining adjuster release handle LH.


b.

Hook the No. 2 reclining adjuster release handle LH on the resin portion of the link.


c.

Pass the No. 2 reclining adjuster release handle LH through the hole of the rear seat lower cushion hinge cover LH.


d.

Install the new rear seatback lock release button.


Hide 71694 24.INSTALL REAR SEAT LOWER CUSHION HINGE COVER LH

a.
B439065C01
0,0 0,0 false
V113147

Install in this Direction


Push as shown in the illustration to attach the claw and guide.


b.

Install the screw to rear seat lower cushion hinge cover LH.