Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR
RM33K0E _59 Vehicle Exterior _043561 WIPER / WASHER _0227139 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85143R 1.INSTALL REAR WIPER MOTOR GROMMET

a.
B407679C01
1.542,1.083 1.698,0.833 1.698,0.833 1.875,1.083 true 1.646,0.646 1.958,0.802 0.313,0.156 10 false *a
*a Lip Portion


Apply MP grease to the entire circumference of the lip portion of the rear wiper motor grommet.

HINT:

Do not fill the hole with MP grease. Only apply MP grease to the grooves of the lip portion.



b.
B407680C01
1.729,0.698 2.042,0.406 true 2.073,0.292 2.385,0.448 0.313,0.156 10 false *a
*a Alignment Mark
V113147

Install in this Direction


Install the rear wiper motor grommet with its alignment mark aligned with the top of the vehicle.


Hide 85110R 2.INSTALL REAR WIPER MOTOR ASSEMBLY

a.
B407681C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Install the rear wiper motor assembly with the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Connect the connector.


Hide 3.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.
B374857C01
2,0.479 2.552,0.292 true 2.042,1.521 2.594,1.333 true 2.604,0.208 2.917,0.365 0.313,0.156 10 false *a 2.677,1.26 2.99,1.417 0.313,0.156 10 false *b
*a Rear Wiper Arm Serrations
*b Rear Wiper Motor Assembly Pivot Serrations


When reinstalling:

NOTICE:

Do not grind the rear wiper arm serrations.


i.

Clean the rear wiper arm serrations.


ii.

Clean the rear wiper motor assembly pivot serrations.



b.

Turn the engine switch on (IG).


c.

Operate the rear wiper motor assembly and stop at the automatic stop (park) position.


d.

Turn the engine switch off.


e.
B407682C02
0.625,0.979 0.51,1.177 false 0.333,1.083 0.646,1.24 0.313,0.156 10 false *a 0.771,0.448 1.083,0.604 0.313,0.156 10 false *b 0.792,1.354 1.104,1.51 0.313,0.156 10 false *b
*a Defogger Line at the Bottom
*b 7.5 mm (0.2953 in.)


Align the rear wiper arm and blade assembly as shown in the illustration and install it with the nut.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)

HINT:

Hold the arm hinge by hand when tightening the nut.



f.

Operate the rear wiper motor assembly while spraying washer fluid on the glass. Make sure that the rear wipers function properly and the wipers do not come into contact with the vehicle body.


g.

Raise the rear wiper arm 2 times and check that the tip of the rear wiper blade is within the range shown in the illustration.


Hide 85292A 4.INSTALL REAR WIPER ARM HEAD CAP

a.
B407676C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to the rear wiper arm and blade assembly.


b.
B407675C01
0,0 0,0 false
V113147

Install in this Direction


Attach the claw to install the rear wiper arm head cap as shown in the illustration.


Hide 67750 5.INSTALL BACK DOOR TRIM BOARD ASSEMBLY

Hide 74811D 6.INSTALL DOOR PULL HANDLE

Hide 67938A 7.INSTALL BACK DOOR SIDE GARNISH LH

Hide 67937B 8.INSTALL BACK DOOR SIDE GARNISH RH

Hide 67939B 9.INSTALL CENTER BACK DOOR GARNISH