Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD)
RM33K0E _57 Power Source / Network _043546 NETWORKING _0227242 CAN COMMUNICATION SYSTEM(for RHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of brake actuator assembly (skid control ECU)

·

Brake actuator assembly (skid control ECU) ground circuit

·

Brake actuator assembly (skid control ECU) CAN branch wire or connector

·

Brake actuator assembly (skid control ECU)



WIRING DIAGRAM

w/VSC:
B338294E14
5.219,5.042 6.813,5.354 1.594,0.313 10 false A4 5.219,5.188 6.813,5.531 1.594,0.344 10 false Brake Actuator Assembly (Skid Control ECU) 5.563,4.208 6.688,4.385 1.125,0.177 10 false GND2 5.573,3.729 6.698,3.906 1.125,0.177 10 false GND1 5.583,3.042 6.708,3.219 1.125,0.177 10 false IG1 5.573,2.552 6.698,2.729 1.125,0.177 10 false BM 5.583,2.094 6.708,2.271 1.125,0.177 10 false +BS 3.896,1.927 4.656,2.177 0.76,0.25 10 false ABS NO.2 3.906,2.385 4.667,2.615 0.76,0.229 10 false ABS NO.1 3.958,2.896 4.75,3.25 0.792,0.354 10 false IG1 NO.3 2.063,2.052 3.021,2.344 0.958,0.292 10 false from Battery 2.073,2.531 3.031,2.792 0.958,0.26 10 false from Battery 0.354,3 2.906,3.271 2.552,0.271 10 false from IG1 NO.1 Relay*1, Ignition Switch*2 5.385,4.083 6.51,4.26 1.125,0.177 10 false 1 5.323,3.594 6.448,3.771 1.125,0.177 10 false 25 5.313,2.938 6.438,3.115 1.125,0.177 10 false 12 5.313,2.438 6.438,2.615 1.125,0.177 10 false 13 5.323,1.969 6.448,2.146 1.125,0.177 10 false 38 5.333,0.854 6.458,1.031 1.125,0.177 10 false 22 5.323,1.26 6.448,1.438 1.125,0.177 10 false 10 5.583,0.969 6.708,1.146 1.125,0.177 10 false CANH 5.583,1.396 6.708,1.573 1.125,0.177 10 false CANL 1.594,1.271 1.969,1.573 0.375,0.302 10 false 2 1.594,0.854 2,1.24 0.406,0.385 10 false 1 0.125,1.708 0.656,2.01 0.531,0.302 10 false G93 0.135,1.854 2.156,2.031 2.021,0.177 10 false No. 1 CAN Junction Connector 0.229,5.146 2.625,5.448 2.396,0.302 10 false *1: w/ Smart Entry and Start System 0.229,5.417 2.625,5.719 2.396,0.302 10 false *2: w/o Smart Entry and Start System

w/o VSC:
B338294E15
5.219,5.01 5.979,5.417 0.76,0.406 10 false A3 5.219,5.167 6.813,5.51 1.594,0.344 10 false Brake Actuator Assembly (Skid Control ECU) 5.573,4.208 6.271,4.521 0.698,0.313 10 false GND2 5.573,3.729 6.698,3.906 1.125,0.177 10 false GND1 5.604,3.042 6.073,3.313 0.469,0.271 10 false IG1 5.573,2.552 6.104,2.906 0.531,0.354 10 false +BM 5.583,2.094 6.708,2.271 1.125,0.177 10 false +BS 3.917,1.927 4.677,2.177 0.76,0.25 10 false ABS NO.2 3.906,2.385 4.667,2.615 0.76,0.229 10 false ABS NO.1 2.094,2.083 2.865,2.26 0.771,0.177 10 false from Battery 2.104,2.542 3.073,2.906 0.969,0.365 10 false from Battery 0.385,2.99 3.01,3.219 2.625,0.229 10 false from IG1 NO.1 Relay*1, Ignition Switch*2 5.302,4.083 6.427,4.26 1.125,0.177 10 false 13 5.406,3.594 5.76,3.906 0.354,0.313 10 false 1 5.333,2.917 5.719,3.333 0.385,0.417 10 false 34 5.323,2.438 5.677,2.802 0.354,0.365 10 false 24 5.313,1.958 5.688,2.281 0.375,0.323 10 false 12 5.302,0.854 5.76,1.385 0.458,0.531 10 false 25 5.313,1.26 6.115,1.688 0.802,0.427 10 false 14 5.583,0.969 6.708,1.146 1.125,0.177 10 false CANH 5.583,1.396 6.708,1.573 1.125,0.177 10 false CANL 1.583,1.26 2.021,1.656 0.438,0.396 10 false 2 1.573,0.844 1.844,1.167 0.271,0.323 10 false 1 0.156,1.75 2.042,1.906 1.885,0.156 10 false G93 0.167,1.917 2.052,2.073 1.885,0.156 10 false No. 1 CAN Junction Connector 3.958,2.896 4.75,3.167 0.792,0.271 10 false IG1 NO.3 0.333,4.781 3.167,5.031 2.833,0.25 10 false *1: w/ Smart Entry and Start System 0.333,5.115 3.167,5.365 2.833,0.25 10 false *2: w/o Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 60 seconds, and then drive the vehicle at a speed of 15 km/h (9 mph) or more for 3 seconds or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
C317099C01
1.448,2.479 1.896,2.771 0.448,0.292 1.458,0.125 1.906,0.417 0.448,0.292 2.094,0.854 2.365,0.313 2.365,0.313 2.51,0.313 true 2.094,1.021 2.344,1.854 2.344,1.854 2.51,1.854 true 0.594,4.417 0.75,4.417 0.75,4.417 1.302,3.688 true 0.531,2.708 0.688,2.708 0.688,2.708 1.292,3.573 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 2.583,1.76 3.198,1.958 0.615,0.198 10 false CANH 2.594,0.219 3.208,0.417 0.615,0.198 10 false CANL 0.167,4.333 0.781,4.531 0.615,0.198 10 false CANH 0.146,2.646 0.76,2.844 0.615,0.198 10 false CANL 1.604,0.177 1.917,0.375 0.313,0.198 10 false A4 1.594,2.531 1.906,2.729 0.313,0.198 10 false A3 1.979,0.198 2.292,0.396 0.313,0.198 10 false *A 1.958,2.542 2.271,2.74 0.313,0.198 10 false *B
*A w/ VSC
*B w/o VSC
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ VSC
Tester Connection Condition Specified Condition
A4-22 (CANH) - A4-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

w/o VSC
Tester Connection Condition Specified Condition
A3-25 (CANH) - A3-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SKID CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
C317099C06
1.448,2.479 1.896,2.771 0.448,0.292 1.458,0.125 1.906,0.417 0.448,0.292 2.542,0.854 2.927,0.302 2.927,0.302 3.073,0.302 true 2.573,1.188 2.844,1.854 2.844,1.854 3.01,1.854 true 0.594,4.427 0.75,4.427 0.75,4.427 1.021,3.656 true 0.531,2.708 0.688,2.708 0.688,2.708 0.99,3.365 true 0.521,0.396 0.677,0.396 0.677,0.396 0.844,0.854 true 0.521,1.781 0.677,1.781 0.677,1.781 0.833,1.177 true 2.354,3.354 2.729,2.729 2.729,2.729 2.875,2.729 true 2.333,3.667 2.646,4.375 2.646,4.375 2.813,4.375 true 2.333,0.865 2.313,0.156 2.313,0.156 2.458,0.156 true 2.042,3.677 1.906,4.479 1.906,4.479 2.073,4.479 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.052,1.76 3.417,1.969 0.365,0.208 10 false +BS 3.125,0.219 3.427,0.417 0.302,0.198 10 false BM 0.177,4.354 0.792,4.552 0.615,0.198 10 false GND2 0.146,2.646 0.76,2.844 0.615,0.198 10 false GND1 1.604,0.177 1.917,0.375 0.313,0.198 10 false A4 1.594,2.531 1.906,2.729 0.313,0.198 10 false A3 1.979,0.198 2.292,0.396 0.313,0.198 10 false *A 1.958,2.542 2.271,2.74 0.313,0.198 10 false *B 0.073,0.333 0.688,0.531 0.615,0.198 10 false GND2 0.104,1.708 0.719,1.906 0.615,0.198 10 false GND1 2.865,4.292 3.208,4.49 0.344,0.198 10 false +BM 2.917,2.615 3.281,2.823 0.365,0.208 10 false +BS 2.5,0.052 2.802,0.25 0.302,0.198 10 false IG1 2.135,4.323 2.479,4.521 0.344,0.198 10 false IG1
*A w/ VSC
*B w/o VSC
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/ VSC
Tester Connection Condition Specified Condition
A4-38 (+BS) - Body ground Always 11 to 14 V
A4-13 (BM) - Body ground Always 11 to 14 V
A4-12 (IG1) - Body ground Ignition switch ON 11 to 14 V

w/o VSC
Tester Connection Condition Specified Condition
A3-12 (+BS) - Body ground Always 11 to 14 V
A3-24 (+BM) - Body ground Always 11 to 14 V
A3-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ VSC
Tester Connection Condition Specified Condition
A4-25 (GND1) - Body ground Always Below 1 Ω
A4-1 (GND2) - Body ground Always Below 1 Ω

w/o VSC
Tester Connection Condition Specified Condition
A3-1 (GND1) - Body ground Always Below 1 Ω
A3-13 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR