Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM33K0E _58 Vehicle Interior _043555 HEATING / AIR CONDITIONING _0227347 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Idle Up Switch Circuit  


DESCRIPTION

When the idle up switch is pushed, the air conditioning amplifier assembly outputs the engine idle up signal. If engine idle up does not occur when the idle up switch is pushed, there may be a problem in the circuit shown below.

WIRING DIAGRAM

E322900E05
5.417,0.885 6.031,1.083 0.615,0.198 10 false SWVC 5.198,0.885 5.417,1.083 0.219,0.198 10 false 4 4.583,0.885 4.802,1.083 0.219,0.198 10 false 3 4.354,0.885 4.563,1.083 0.208,0.198 10 false E 2.958,0.885 3.333,1.083 0.375,0.198 10 false SW 2.75,0.885 2.969,1.083 0.219,0.198 10 false 6 3.219,1.302 3.594,1.5 0.375,0.198 10 false G160 3.25,1.469 4.25,1.667 1,0.198 10 false Idle Up Switch 5.26,1.74 5.635,1.938 0.375,0.198 10 false G37 5.271,1.896 6.833,2.427 1.563,0.531 10 false Air Conditioning Amplifier Assembly 2.146,1.146 2.854,1.313 0.708,0.167 10 false IG1 NO.4 0.302,0.979 1.719,1.167 1.417,0.188 10 false from IG1 NO.1 Relay

CAUTION / NOTICE / HINT

NOTICE:

When the servo motor or air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION


HINT:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS (IDLE UP/PWR HEAT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IDLE UP/PWR HEAT Switch Idle up switch ON or OFF ON: Idle up switch on
OFF: Idle up switch off
-
Body Electrical > Air Conditioner > Data List
Tester Display
IDLE UP/PWR HEAT Switch
50003 121 173
OK:

The display is as specified in the normal condition column.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

2.CHECK IDLE UP SWITCH
2.CHECK IDLE UP SWITCH
a.
E322901C05
1.458,0.26 1.958,0.51 0.5,0.25 1.979,1.417 2.229,1.833 2.229,1.833 2.563,1.833 true 0.031,0.052 0.344,0.25 0.313,0.198 10 false *a 2.615,1.74 2.927,1.938 0.313,0.198 10 false SW 1.542,0.302 2,0.479 0.458,0.177 10 false G160
*a Front view of wire harness connector
(to Idle Up Switch)


Disconnect the idle up switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G160-6 (SW) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT IDLE UP SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT IDLE UP SWITCH


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IDLE UP SWITCH - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (IDLE UP SWITCH - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the G160 idle up switch connector.


b.

Disconnect the G37 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G160-3 (E) - G37-4 (SWVC) Always Below 1 Ω
G160-3 (E) or G37-4 (SWVC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR