The air conditioning amplifier assembly sends operation signals to the PTC heater relays when quick heater assembly operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC heater relays turn on, and power is supplied to the quick heater assembly installed in the air conditioning radiator assembly.
| Control ECU | Condition |
|---|---|
| Air Conditioning Amplifier Assembly | Start the engine |
| ECO mode switch: Off | |
| Blower switch: LO or more | |
| Temperature settings: MAX HOT | |
| Light control switch: Off | |
·
Engine coolant temperature 65°C (149°F), or lower (3 PTC heater relays operating) ·
Engine coolant temperature 70°C (158°F), or lower (2 PTC heater relays operating) ·
Engine coolant temperature 75°C (167°F), or lower (A PTC heater relay operating) |
|
| Ambient temperature 10°C (50°F) or lower |
Inspect the fuses for circuits related to this system before performing the following procedure.
Remove the PTC heater relays from the No. 5 instrument panel relay block.
Inspect the PTC heater relays.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the PTC heater relays from the No. 5 instrument panel relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 5 - Body ground | Always | 11 to 14 V |
| Relay terminal 1 - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 5 - Body ground | Always | 11 to 14 V |
| Relay terminal 1 - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 5 - Body ground | Always | 11 to 14 V |
| Relay terminal 2 - Body ground | Ignition switch off | Below 1 V |
| Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the PTC heater relays from the No. 5 instrument panel relay block.
Disconnect the G107 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 2 - G107-13 (PTC1) | Always | Below 1 Ω |
| Relay terminal 2 or G107-13 (PTC1)- Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 2 - G107-19 (PTC2) | Always | Below 1 Ω |
| Relay terminal 2 or G107-19 (PTC2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 1 - G107-20 (PTC3) | Always | Below 1 Ω |
| Relay terminal 1 or G107-20 (PTC3) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the PTC heater relays from the No. 5 instrument panel relay block.
Disconnect the G161 and G162 quick heater assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G162-3 - Relay terminal 3 | Always | Below 1 Ω |
| G162-1 - Body ground | Always | Below 1 Ω |
| G162-2 - Body ground | Always | Below 1 Ω |
| G162-3 or relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G162-1 - Relay terminal 3 | Always | Below 1 Ω |
| G162-2 - Body ground | Always | Below 1 Ω |
| G162-1 or relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G161-2- Relay terminal 3 | Always | Below 1 Ω |
| G161-1 - Body ground | Always | Below 1 Ω |
| G161-2 or relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the quick heater assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>PTC HEATER ASSEMBLY>REMOVAL
Inspect the quick heater assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>PTC HEATER ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG