Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM
RM33K0E _56 Audio / Visual / Telematics _043543 PARK ASSIST / MONITORING _0227352 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Clearance Warning ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the clearance warning ECU assembly.

WIRING DIAGRAM

E335902E01
2.271,0.635 3.5,0.833 1.229,0.198 10 false IG1 NO.4 5.135,1.833 5.594,2.031 0.458,0.198 10 false G88 5.146,2 6.656,2.344 1.51,0.344 10 false Clearance Warning ECU Assembly 3.021,0.365 3.333,0.563 0.313,0.198 10 false IG 2.792,0.354 2.948,0.552 0.156,0.198 10 false 6 4.354,0.354 4.813,0.552 0.458,0.198 10 false ECU 4.542,0.656 4.698,0.854 0.156,0.198 10 false E 5.073,0.354 5.385,0.552 0.313,0.198 10 false 11 5.104,1.25 5.417,1.448 0.313,0.198 10 false 16 5.375,0.479 5.688,0.677 0.313,0.198 10 false IG 4.781,0.354 4.938,0.552 0.156,0.198 10 false 3 4.792,0.656 4.948,0.854 0.156,0.198 10 false 7 0.094,0.479 3.302,0.677 3.208,0.198 10 false from IG1 NO.1 Rleay*1 0.177,1.167 3.385,1.365 3.208,0.198 10 false from Ignition Switch*2 2.927,1.365 4.885,1.781 1.958,0.417 10 false Back Sonar or Clearance Sonar Switch Assembly 2.917,1.198 3.375,1.396 0.458,0.198 10 false G87 0.146,1.865 5.188,2.063 5.042,0.198 10 false *1: w/ Smar Entry and Start System 0.156,2.25 5.198,2.448 5.042,0.198 10 false *2: w/o Smar Entry and Start System 1.76,0.313 2.073,0.51 0.313,0.198 10 false *1 1.823,1.333 2.135,1.531 0.313,0.198 10 false *2 5.365,1.396 5.521,1.594 0.156,0.198 10 false E

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
E318094C02
1.333,0.219 1.917,0.469 0.583,0.25 2.479,2.042 2.146,2.042 2.146,2.042 1.979,1.469 true 2.76,1.844 2.427,1.844 2.427,1.844 2.177,1.448 true 0.042,0.042 0.354,0.24 0.313,0.198 10 false *a 2.531,1.958 3.01,2.146 0.479,0.188 10 false IG 1.49,0.26 1.969,0.448 0.479,0.188 10 false G87 2.813,1.75 3.292,1.938 0.479,0.188 10 false E
*a Front view of wire harness connector
(to Back Sonar or Clearance Sonar Switch Assembly)


Disconnect the back sonar or clearance sonar switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G87-7 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G87-6 (IG) - Body ground Ignition switch ON 11 to 14 V
G87-6 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
a.

Remove the back sonar or clearance sonar switch assembly.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>REMOVAL


b.

Inspect the back sonar or clearance sonar switch assembly.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY)

NG

REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY)
a.

Disconnect the G88 clearance warning ECU assembly connector.


b.

Disconnect the G87 back sonar or clearance sonar switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G88-11 (IG) - G87-3 (ECU) Always Below 1 Ω
G88-16 (E) - Body ground Always Below 1 Ω
G88-11 (IG) or G87-3 (ECU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR