The display signal from the rear television camera assembly is transmitted to the radio and display receiver assembly.
When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Service.
Disconnect the G101 radio and display receiver assembly connector.
Disconnect the V21 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G101-11 (CA+) - V21-6 (CB+) | Always | Below 1 Ω |
| G101-12 (V+) - V21-3 (CV+) | Always | Below 1 Ω |
| G101-23 (CGND) - V21-5 (CGND) | Always | Below 1 Ω |
| G101-24 (V-) - V21-2 (CV-) | Always | Below 1 Ω |
| G101-11 (CA+) or V21-6 (CB+) - Body ground | Always | 10 kΩ or higher |
| G101-12 (V+) or V21-3 (CV+) - Body ground | Always | 10 kΩ or higher |
| G101-23 (CGND) or V21-5 (CGND) - Body ground | Always | 10 kΩ or higher |
| G101-24 (V-) or V21-2 (CV-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Remove the radio and display receiver assembly with its connectors still connected.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G101-23 (CGND) - Body ground | Always | Below 1 Ω |
| G101-24 (V-) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G101-11 (CA+) - Body ground | Ignition switch ACC | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the radio and display receiver assembly with its connectors still connected.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
*b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
Check the waveform of the television rear camera assembly using an oscilloscope.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.
The video waveform changes according to the image sent by the rear television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G101-12 (V+) - G101-23 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Waveform 1: Ignition switch ON, shift lever in R, camera lens not covered, displaying an image
Waveform 2: Ignition switch ON, shift lever in R, camera lens covered, blacking out screen |
Waveform is as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the rear television camera assembly with a new or known good one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA>REMOVAL
Check if the same malfunction recurs when the rear view monitor screen is displayed.
Malfunction does not reoccur (returns to normal).
| Proceed to |
|---|
| OK |
| NG |
OK
NG