Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM33K0E _58 Vehicle Interior _043550 METER / GAUGE / DISPLAY _0227399 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
B1507 Open in Turn Signal Circuit Open in turn signal light circuit.
·

Harness or connector

·

Side turn signal light assembly

·

Outer rear view mirror assembly

·

Rear combination light socket and wire sub-assembly

·

Combination meter assembly


B1508 Short in Turn Signal / Hazard Flasher Circuit Short in turn signal light circuit or hazard warning light circuit.
·

Harness or connector

·

Side turn signal light assembly

·

Outer rear view mirror assembly

·

Rear combination light socket and wire sub-assembly

·

Combination meter assembly



WIRING DIAGRAM

LH SIde:


E339231E01
6.083,4.333 6.396,4.531 0.313,0.198 10 false G10 6.083,4.5 7.125,4.906 1.042,0.406 10 false Combination Meter Assembly 6.229,0.823 6.542,1.021 0.313,0.198 10 false LL 6.042,0.719 6.354,0.917 0.313,0.198 10 false 8 0.365,1.552 0.677,1.75 0.313,0.198 10 false K3 0.354,1.729 2.781,2 2.427,0.271 10 false Outer Rear View Mirror Assembly LH 2.292,0.99 2.604,1.188 0.313,0.198 10 false Turn 2.104,2.698 2.417,2.896 0.313,0.198 10 false Turn 0.969,4.313 1.281,4.51 0.313,0.198 10 false Turn 0.365,3.146 0.677,3.344 0.313,0.198 10 false A63 0.365,3.292 2.792,3.563 2.427,0.271 10 false Headlight Assembly LH 0.302,4.781 1.729,5.188 1.427,0.406 10 false Rear Combination Light Assembly LH 2.833,0.75 3.25,0.948 0.417,0.198 10 false TRNL 3.24,0.74 3.656,0.938 0.417,0.198 10 false 10 2.865,1.156 3.281,1.354 0.417,0.198 10 false GND 3.271,1.125 3.688,1.323 0.417,0.198 10 false 6 3.042,2.49 3.458,2.688 0.417,0.198 10 false B 3.26,2.49 3.677,2.688 0.417,0.198 10 false 2 3.042,2.74 3.458,2.938 0.417,0.198 10 false E 3.26,2.729 3.677,2.927 0.417,0.198 10 false 1 3.052,4.094 3.469,4.292 0.417,0.198 10 false B 3.063,4.333 3.479,4.531 0.417,0.198 10 false E 3.26,4.094 3.677,4.292 0.417,0.198 10 false 3 3.26,4.354 3.677,4.552 0.417,0.198 10 false 5 1.823,4.771 2.135,4.969 0.313,0.198 10 false N33 1.813,4.927 3.708,5.271 1.896,0.344 10 false Rear Combination Light Socket and Wire Sub-assembly LH


RH SIde:


E339231E02
6.083,4.333 6.396,4.531 0.313,0.198 10 false G10 6.083,4.5 7.125,4.906 1.042,0.406 10 false Combination Meter Assembly 6.229,0.823 6.542,1.021 0.313,0.198 10 false LR 5.99,0.719 6.302,0.917 0.313,0.198 10 false 13 0.365,1.552 0.677,1.75 0.313,0.198 10 false J2 0.354,1.729 2.781,2 2.427,0.271 10 false Outer Rear View Mirror Assembly RH 2.292,0.99 2.604,1.188 0.313,0.198 10 false Turn 2.104,2.698 2.417,2.896 0.313,0.198 10 false Turn 0.969,4.313 1.281,4.51 0.313,0.198 10 false Turn 0.365,3.146 0.677,3.344 0.313,0.198 10 false A62 0.365,3.292 2.792,3.563 2.427,0.271 10 false Headlight Assembly RH 1.792,4.781 2.104,4.979 0.313,0.198 10 false N32 0.229,4.771 1.667,5.094 1.438,0.323 10 false Rear Combination Light Assembly RH 2.833,0.75 3.25,0.948 0.417,0.198 10 false TRNR 3.24,0.74 3.656,0.938 0.417,0.198 10 false 10 2.865,1.156 3.281,1.354 0.417,0.198 10 false GND 3.271,1.146 3.688,1.344 0.417,0.198 10 false 6 3.042,2.49 3.458,2.688 0.417,0.198 10 false B 3.26,2.49 3.677,2.688 0.417,0.198 10 false 2 3.042,2.74 3.458,2.938 0.417,0.198 10 false E 3.26,2.729 3.677,2.927 0.417,0.198 10 false 1 3.052,4.094 3.469,4.292 0.417,0.198 10 false B 3.063,4.333 3.479,4.531 0.417,0.198 10 false E 3.25,4.094 3.667,4.292 0.417,0.198 10 false 3 3.271,4.354 3.688,4.552 0.417,0.198 10 false 5 1.802,4.948 3.74,5.302 1.938,0.354 10 false Rear Combination Light Socket and Wire Sub-assembly RH


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

Inspect the bulbs for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Clear DTCs
50002 122

b.

Recheck for DTCs and check that no DTCs are output.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122
OK:

B1507 and B1508 are not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TURN SIGNAL LIGHT
2.CHECK TURN SIGNAL LIGHT
a.

Check the illumination of each turn signal light.


Result:
Result Proceed to
LH side turn signal light does not illuminate. A
RH side turn signal light does not illuminate. B



A

3.CHECK HARNESS AND CONNECTOR (LH SIDE CIRCUIT)

B

7.CHECK HARNESS AND CONNECTOR (RH SIDE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (LH SIDE CIRCUIT)
a.

Disconnect the G10 combination meter assembly connector.


b.

Disconnect the A63 headlight assembly LH connector.


c.

Disconnect the K3 outer rear view mirror assembly LH connector.


d.

Disconnect the N33 rear combination light socket and wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G10-8 (LL) - A63-2 (B) Always Below 1 Ω
G10-8 (LL) - K3-10 (TRNL) Always Below 1 Ω
G10-8 (LL) - N33-3 (B) Always Below 1 Ω
A63-1 (E) - Body ground Always Below 1 Ω
K3-6 (GND) - Body ground Always Below 1 Ω
N33-5 (E) - Body ground Always Below 1 Ω
G10-8 (LL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.

Remove the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH

NG

6.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH
5.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH
a.
E339232C01
0.792,1.875 0.958,1.875 0.958,1.875 1.188,1.417 true 2.542,1.854 2.375,1.854 2.375,1.854 2.208,1.438 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 0.677,1.802 0.99,2 0.313,0.198 10 false B 2.604,1.781 2.917,1.979 0.313,0.198 10 false E
*a Component without harness connected
(Rear Combination Light Assembly LH)


Remove the rear combination light socket and wire sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.

Apply battery voltage to the connector and check the light illumination condition.

OK:
Condition Specified Condition
Battery positive (+) → 3 (B)
Battery negative (-) → 6 (E)
Trun signal light illuminates



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH

6.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH
a.

Remove the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Inspect the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (RH SIDE CIRCUIT)
a.

Disconnect the G10 combination meter assembly connector.


b.

Disconnect the A62 headlight assembly RH connector.


c.

Disconnect the J2 outer rear view mirror assembly RH connector.


d.

Disconnect the N32 rear combination light assembly RH or rear combination light socket and wire sub-assembly RH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G10-13 (LR) - A62-2 (B) Always Below 1 Ω
G10-13 (LR) - J2-10 (TRNR) Always Below 1 Ω
G10-13 (LR) - N32-3 (B) Always Below 1 Ω
A62-1 (E) - Body ground Always Below 1 Ω
J2-6 (GND) - Body ground Always Below 1 Ω
N32-5 (E) - Body ground Always Below 1 Ω
G10-13 (LR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.

Remove the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.

Inspect the outer rear view mirror assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION


Result:
Proceed to
OK
NG



OK

9.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH

NG

10.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH
9.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH
a.

Remove the rear combination light socket and wire sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.
E339232C01
0.792,1.875 0.958,1.875 0.958,1.875 1.188,1.417 true 2.542,1.854 2.375,1.854 2.375,1.854 2.208,1.438 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 0.677,1.802 0.99,2 0.313,0.198 10 false B 2.604,1.781 2.917,1.979 0.313,0.198 10 false E
*a Component without harness connected
(Rear Combination Light Assembly RH)


Apply battery voltage to the connector and check the light illumination condition.

OK:
Condition Specified Condition
Battery positive (+) → 3 (B)
Battery negative (-) → 6 (E)
Trun signal light illuminates



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH

10.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH
a.

Remove the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Inspect the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH