Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM33K0E _58 Vehicle Interior _043554 SEAT BELT _0227708 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

When the ignition switch is turned to ON, the combination meter assembly receives a signal of the front seat inner belt assembly LH*1 or RH*2. If the driver side seat belt is not fastened, the combination meter assembly blinks the seat belt warning light. If the seat belt is fastened, the warning light goes off.

·

*1: for LHD

·

*2: for RHD


HINT:

The front seat belt warning light on the combination meter assembly is used for both the driver side seat and front passenger side seat.


WIRING DIAGRAM

E319790E10
5.521,2.552 5.677,2.75 0.156,0.198 10 false A 3.24,1.458 3.552,1.656 0.313,0.198 10 false 2L 3.24,1.635 4.854,2.021 1.615,0.385 10 false Instrument Panel Junction Block Assembly 3.021,0.729 3.177,0.927 0.156,0.198 10 false 1 1.615,3.229 1.771,3.427 0.156,0.198 10 false 3 1.875,4.229 5.854,4.427 3.979,0.198 10 false Combination Meter Assembly 1.875,4.063 2.188,4.26 0.313,0.198 10 false G10 2.917,6.104 4.083,6.313 1.167,0.208 10 false N18*1, N17*2 2.927,6.281 5.833,6.458 2.906,0.177 10 false Front Seat Inner Belt Assembly LH*1, RH*2 2.969,5.333 3.125,5.531 0.156,0.198 10 false 3 4.906,5.323 5.063,5.521 0.156,0.198 10 false 2 2.438,3.365 2.896,3.563 0.458,0.198 10 false I/F 3.052,3.365 3.51,3.563 0.458,0.198 10 false CPU 4.938,0.729 5.25,0.927 0.313,0.198 10 false 23 5.313,0.865 5.896,1.073 0.583,0.208 10 false DBKL*3 1.865,3.24 2.323,3.438 0.458,0.198 10 false BKL 5.51,2.729 6.74,2.927 1.229,0.198 10 false Body ECU 0.135,5.646 1.823,5.844 1.688,0.198 10 false *1: for LHD 0.146,6.01 1.833,6.208 1.688,0.198 10 false *2: for RHD 3.49,5.719 7.156,5.958 3.667,0.24 10 false Buckle Switch 0.146,6.365 2.635,6.583 2.49,0.219 10 false *3: w/ Power Door Lock Control System

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, make sure to replace it with a new one.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (DRIVER SIDE SEAT BELT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Driver Side Seat Belt Seat belt warning light OFF/ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Driver Side Seat Belt
50004 122 12
OK:

The seat belt warning light on the combination meter assembly operates normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (DRIVER SIDE SEATBELT BUCKLE SWITCH)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING GTS (DRIVER SIDE SEATBELT BUCKLE SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical /Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Seatbelt Buckle Switch Driver side seat belt buckle switch signal ON or OFF ON: Driver side seat belt unfastened
OFF: Driver side seat belt fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
Driver Side Seatbelt Buckle Switch
50003 122 119

Result:
Result Proceed to
ON or OFF is displayed on the GTS screen according to the driver side seat belt condition A
ON or OFF is not displayed normally on the GTS screen according to the driver side seat belt condition (for LHD) B
ON or OFF is not displayed normally on the GTS screen according to the driver side seat belt condition (for RHD) C



A

REPLACE COMBINATION METER ASSEMBLY

B

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH

C

5.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH
3.INSPECT FRONT SEAT INNER BELT ASSEMBLY LH


Result:
Result Proceed to
OK A
NG (for Manual Seat) B
NG (for Power Seat) C



A

4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

C

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

4.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N18 front seat inner belt assembly LH connector.


b.

Disconnect the G10 combination meter assembly connector.


c.

Disconnect the 2L instrument panel junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N18-3 - G10-3 (BKL) Always Below 1 Ω
N18-2 - Body ground Always Below 1 Ω
N18-3 or G10-3 (BKL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH


Result:
Result Proceed to
OK A
NG (for Manual Seat) B
NG (for Power Seat) C



A

6.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

C

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

6.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the N17 front seat inner belt assembly RH connector.


b.

Disconnect the G10 combination meter assembly connector.


c.

Disconnect the 2L instrument panel junction block assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N17-3 - G10-3 (BKL) Always Below 1 Ω
N17-2 - Body ground Always Below 1 Ω
N17-3 or G10-3 (BKL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR