Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY
RM33K0E _58 Vehicle Interior _043554 SEAT BELT _0229923 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power back door system (Click here)

CAUTION:
B394719

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67914B 3.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 67918E 4.REMOVE REAR DOOR SCUFF PLATE LH

Hide 73233 5.REMOVE OUTER LAP BELT ANCHOR COVER

Hide 73220 6.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (Floor Anchor)

a.
B416208

Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly LH.


Hide 62414A 7.REMOVE LOWER CENTER PILLAR GARNISH LH

Hide 73178A 8.REMOVE SEAT BELT ANCHOR COVER CAP

Hide 73220 9.REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

a.
B416209

Remove the bolt and disconnect the shoulder anchor of the front seat outer belt assembly LH.


b.
B437143C01
1.021,0.417 1.219,0.333 false 1.271,0.25 1.583,0.448 0.313,0.198 10 false *1
*1 Locking Button
V100155

Protective Tape


Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector as shown in the illustration.

HINT:

Tape the screwdriver tip before use.



c.
B437144

Remove the bolt.


d.

Detach the 2 guides and remove the front seat outer belt assembly LH.


Hide 62412B 10.REMOVE UPPER CENTER PILLAR GARNISH LH

Hide 73024 11.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

HINT:

Perform this procedure when replacing the shoulder belt anchor plate sub-assembly LH.


a.
B437145

Detach the claw and remove the front shoulder belt anchor plate sub-assembly LH in the illustration.


Hide 73136A 12.REMOVE SHOULDER BELT ANCHOR COVER LH

HINT:

Perform this procedure when replacing the shoulder belt anchor cover LH.


a.
B409156C01
1.729,1.344 2.365,1.521 2.365,1.521 1.75,1.938 true 2.438,1.448 2.75,1.604 0.313,0.156 10 false *1
*1 Shoulder Belt Anchor Cover LH


Detach the claw and remove the 2 shoulder belt anchor cover LH.


Hide 73200A 13.REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

a.
B404843

Remove the 2 bolts.


b.

Detach the guide to remove the front shoulder belt anchor adjuster assembly.