Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING
RM33K0E _58 Vehicle Interior _043557 INTERIOR PANELS / TRIM _0227574 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the roof headlining removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power door lock control system (Click here)

CAUTION:
B410193

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.REMOVE REAR NO. 2 SEAT ASSEMBLY LH

Hide 4.REMOVE REAR NO. 2 SEAT ASSEMBLY RH

Hide 74603 5.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY

Hide 62212 6.REMOVE FRONT PILLAR GARNISH LH

Hide 62211 7.REMOVE FRONT PILLAR GARNISH RH

Hide 67914B 8.REMOVE FRONT DOOR SCUFF PLATE LH

a.
B409855C01
2.906,1.74 3.156,1.479 true 3.083,1.323 3.302,1.479 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the front door scuff plate LH.


b.
B409857C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the front door scuff plate LH.


Hide 67913B 9.REMOVE FRONT DOOR SCUFF PLATE RH

a.
B409858C01
0.531,1.74 0.344,1.302 true 0.229,1.146 0.448,1.302 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the front door scuff plate RH.


b.
B409860C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the front door scuff plate RH.


Hide 67918E 10.REMOVE REAR DOOR SCUFF PLATE LH

a.
B409861C01
0.292,0.75 0.427,0.615 true 0.156,0.729 0.375,0.885 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the rear door scuff plate LH.


b.
B409863C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the rear door scuff plate LH.


Hide 67917C 11.REMOVE REAR DOOR SCUFF PLATE RH

a.
B409864C01
3.135,0.75 3,0.615 true 3.073,0.719 3.302,0.875 0.229,0.156 10 true *a
*a Protective Tape


Put protective tape around the rear door scuff plate RH.


b.
B409866C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and remove the rear door scuff plate RH.


Hide 73233 12.REMOVE OUTER LAP BELT ANCHOR COVER

HINT:

Use the same procedure for both outer lap belt anchor covers.


a.
B409867C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the outer lap belt anchor cover as shown in the illustration.


Hide 62414A 13.REMOVE LOWER CENTER PILLAR GARNISH LH

a.
B404564

Remove the bolt and disconnect the front seat outer belt assembly LH.


b.
B404565C01
3.083,1.5 3.323,1.667 0.24,0.167 10 false *1 0.354,1.51 0.667,1.667 0.313,0.156 10 false *2
*1 Front Door Opening Trim Weatherstrip LH
*2 Rear Door Opening Trim Weatherstrip LH


Disconnect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.


c.
B404566C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower center pillar garnish LH.


Hide 62413A 14.REMOVE LOWER CENTER PILLAR GARNISH RH

a.
B404568

Remove the bolt and disconnect the front seat outer belt assembly RH.


b.
B404569C01
0.208,1.521 0.521,1.677 0.313,0.156 10 false *1 2.927,1.51 3.24,1.667 0.313,0.156 10 false *2
*1 Front Door Opening Trim Weatherstrip RH
*2 Rear Door Opening Trim Weatherstrip RH


Disconnect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.


c.
B404570C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the lower center pillar garnish RH.


Hide 73178A 15.REMOVE SEAT BELT ANCHOR COVER CAP

HINT:

Use the same procedure for both seat belt anchor cover caps.


a.
B404572C01
0.458,0.75 1.313,0.885 true 0.281,0.625 0.594,0.781 0.313,0.156 10 false *a
*a Protective Tape


Put protective tape around the seat belt anchor cover cap.


b.
B404573C01
0.969,1.229 1.198,0.813 true 0.833,1.219 1.042,1.375 0.208,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here
V113147

Remove in this Direction


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the seat belt anchor cover cap.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 62412B 16.REMOVE UPPER CENTER PILLAR GARNISH LH

a.
B404578

Remove the bolt and disconnect the front seat outer belt assembly LH.


b.
B404580C01
2.729,1.688 3.042,1.844 0.313,0.156 10 false *1 0.229,1.708 0.542,1.865 0.313,0.156 10 false *2
*1 Front Door Opening Trim Weatherstrip LH
*2 Rear Door Opening Trim Weatherstrip LH


Disconnect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.


c.
B404579C01
0,0 0,0 false
V113146

Insert Clip Remover Here
V113147

Remove in this Direction


Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the upper center pillar garnish LH.


Hide 62411B 17.REMOVE UPPER CENTER PILLAR GARNISH RH

a.
B404582

Remove the bolt and disconnect the front seat outer belt assembly RH.


b.
B404584C01
0.49,1.698 0.802,1.854 0.313,0.156 10 false *1 2.979,1.698 3.208,1.854 0.229,0.156 10 false *2
*1 Front Door Opening Trim Weatherstrip RH
*2 Rear Door Opening Trim Weatherstrip RH


Disconnect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.


c.
B404583C01
0,0 0,0 false
V113146

Insert Clip Remover Here
V113147

Remove in this Direction


Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the upper center pillar garnish RH.


Hide 67935 18.REMOVE BACK DOOR SCUFF PLATE

a.

Put protective tape around the back door scuff plate.

B409871C01
1.177,1.771 1.021,1.26 true 0.906,1.104 1.115,1.26 0.208,0.156 10 true *a
*a Protective Tape - -



b.

Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the back door scuff plate.

B409872C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction



Hide 73233A 19.REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

HINT:

Use the same procedure for both rear No. 1 seat outer lap belt anchor covers.


a.
B409874C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the rear No. 1 seat outer lap belt anchor cover as shown in the illustration.


Hide 73233B 20.REMOVE REAR NO. 2 SEAT OUTER LAP BELT ANCHOR COVER

HINT:

Use the same procedure for both rear No. 2 seat outer lap belt anchor covers.


a.
B409880C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the rear No. 2 seat outer lap belt anchor cover as shown in the illustration.


Hide 62512 21.REMOVE QUARTER INSIDE TRIM BOARD LH

a.
B409879

Remove the bolt and disconnect the rear No. 1 seat outer belt assembly LH.


b.
B409885

Remove the bolt and disconnect the rear No. 2 seat outer belt assembly LH.


c.
B409887C01
3.083,1.573 3.344,1.729 0.26,0.156 10 false *1
*1 Rear Door Opening Trim Weatherstrip LH


Disconnect the rear door opening trim weatherstrip LH in the range shown in the illustration.


d.
B409889C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip and remove the quarter inside trim board LH.


Hide 62511 22.REMOVE QUARTER INSIDE TRIM BOARD RH

a.
B409878

Remove the bolt and disconnect the rear No. 1 seat outer belt assembly RH.


b.
B409884

Remove the bolt and disconnect the rear No. 2 seat outer belt assembly RH.


c.
B409886C01
0.198,1.708 0.51,1.865 0.313,0.156 10 false *1
*1 Rear Door Opening Trim Weatherstrip RH


Disconnect the rear door opening trim weatherstrip RH in the range shown in the illustration.


d.
B409888C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Place your hands at the position shown in the illustration and pull as shown to detach the claw and clip.


e.

Disconnect the connector and remove the quarter inside trim board RH.


Hide 73178B 23.REMOVE SEAT BELT ANCHOR COVER CAP

HINT:

Use the same procedure for both seat belt anchor cover caps.


a.
B409892C01
0.698,0.375 1.281,0.531 true 0.479,0.281 0.698,0.438 0.219,0.156 10 true *a
*a Protective Tape


Put protective tape around the seat belt anchor cover cap.


b.
B409894C01
0.854,1.135 1.271,0.719 true 0.698,1.094 0.927,1.25 0.229,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here
V113147

Remove in this Direction


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the seat belt anchor cover cap.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 62639A 24.REMOVE QUARTER PILLAR GARNISH LH

a.
B409899

Remove the bolt and disconnect the rear No. 1 seat outer belt assembly LH.


b.
B409905C01
3.042,1 3.292,1.167 0.25,0.167 10 false *1
*1 Rear Door Opening Trim Weatherstrip LH


Disconnect the rear door opening trim weatherstrip LH in the range shown in the illustration.


c.
B409901C01
0,0 0,0 false
V113146

Insert Clip Remover Here
V113147

Remove in this Direction


Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the quarter pillar garnish LH.


Hide 62638A 25.REMOVE QUARTER PILLAR GARNISH RH

a.
B409898

Remove the bolt and disconnect the rear No. 1 seat outer belt assembly RH.


b.
B409904C01
0.25,1.031 0.563,1.188 0.313,0.156 10 false *1
*1 Rear Door Opening Trim Weatherstrip RH


Disconnect the rear door opening trim weatherstrip RH in the range shown in the illustration.


c.
B409900C01
0,0 0,0 false
V113146

Insert Clip Remover Here
V113147

Remove in this Direction


Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the quarter pillar garnish RH.


Hide 73178B 26.REMOVE SEAT BELT ANCHOR COVER CAP

HINT:

Use the same procedure for both seat belt anchor cover caps.


a.
B409906C01
2.125,0.542 2.917,0.344 true 2.948,0.24 3.26,0.396 0.313,0.156 10 false *a
*a Protective Tape


Put protective tape around the seat belt anchor cover cap.


b.
B409908C01
2.385,1.188 2.094,0.656 true 2.354,1.167 2.563,1.333 0.208,0.167 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here
V113147

Remove in this Direction


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the seat belt anchor cover cap.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 62472D 27.REMOVE UPPER REAR PILLAR GARNISH LH

a.
B409913

Remove the bolt and disconnect the rear No. 2 seat outer belt assembly LH.


b.
B409915

Remove the bolt and rear seat hook.


c.
B409917C01
0,0 0,0 false
V113146

Insert Clip Remover Here
V113147

Remove in this Direction


Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the upper rear pillar garnish LH.


Hide 62471D 28.REMOVE UPPER REAR PILLAR GARNISH RH

a.
B409912

Remove the bolt and disconnect the rear No. 2 seat outer belt assembly RH.


b.
B409914

Remove the bolt and rear seat hook.


c.
B409916C01
0,0 0,0 false
V113146

Insert Clip Remover Here
V113147

Remove in this Direction


Insert a clip remover at the position shown in the illustration and pull as shown to detach the clip and remove the upper rear pillar garnish RH.


Hide 81260A 29.REMOVE MAP LIGHT ASSEMBLY

Hide 81360T 30.REMOVE SPOT LIGHT ASSEMBLY

Hide 81240 31.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 73139C 32.REMOVE REAR SEAT BELT COVER

a.
B409920C01
0,0 0,0 false
V113146

Insert Moulding Remover D Here
V113147

Remove in this Direction


Insert moulding remover D at the position shown in the illustration and pull as shown to detach the clip, claw and guide and remove the rear seat belt cover.


Hide 74325 33.REMOVE VISOR BRACKET COVER LH

a.

Open the visor assembly LH.


b.
B404635C01
0.667,1.427 1.198,1.677 true 0.458,1.292 0.688,1.448 0.229,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the visor bracket cover LH.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 74325 34.REMOVE VISOR BRACKET COVER RH

a.

Open the visor assembly RH.


b.
B404636C01
2.188,1.625 2.792,1.365 true 2.802,1.229 3.031,1.385 0.229,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the visor bracket cover RH.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 74320 35.REMOVE VISOR ASSEMBLY LH

a.
B404637

Remove the 2 screws.


b.
B404639C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull in the direction (1) shown in the illustration to disconnect the visor assembly LH from the visor holder.


c.

Pull in the direction (2) shown in the illustration to remove the visor assembly LH.


Hide 74310 36.REMOVE VISOR ASSEMBLY RH

a.
B404638

Remove the 2 screws.


b.
B404640C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Pull in the direction (1) shown in the illustration to disconnect the visor assembly RH from the visor holder.


c.

Pull in the direction (2) shown in the illustration to remove the visor assembly RH.


Hide 74348 37.REMOVE VISOR HOLDER

HINT:

Use the same procedure for both visor holders.


a.
B404621C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.


b.

Detach the claw and remove the visor holder.


Hide 74610A 38.REMOVE ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for all assist grip sub-assemblies.


a.
B410684C01
0.646,3.635 1.208,3.219 true 0.563,3.521 0.771,3.698 0.208,0.177 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the assist grip cover.

HINT:
·

Use the same procedure for both assist grip covers.

·

Tape the thin-bladed screwdriver tip before use.




b.
B410685

Pinch the clip with needle-nose pliers.

HINT:

Use the same procedure for both clips.



c.
B410686C01
0,0 0,0 false
V113147

Remove in this Direction


Hold the handle and pull as shown in the illustration to remove the assist grip sub-assembly.


d.

Using needle-nose pliers, remove the clip.


Hide 74620B 39.REMOVE REAR ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure for both rear assist grip assemblies.


a.
B410689C01
0.531,4.042 1.156,3.271 true 0.396,4.01 0.615,4.167 0.219,0.156 10 true *a
*a Protective Tape
V113146

Insert Thin-bladed Screwdriver Here


Insert a thin-bladed screwdriver at the position shown in the illustration and detach the claw and remove the assist grip cover.

HINT:
·

Use the same procedure for both assist grip covers.

·

Tape the thin-bladed screwdriver tip before use.




b.
B410690

Pinch the clip with needle-nose pliers.

HINT:

Use the same procedure for both clips.



c.
B410691C01
0,0 0,0 false
V113147

Remove in this Direction


Hold the handle and pull as shown in the illustration to remove the rear assist grip assembly.


d.

Using needle-nose pliers, remove the clip.


Hide 63310 40.REMOVE ROOF HEADLINING ASSEMBLY

a.
B409922

Disconnect the connector and detach the clamp from the front pillar LH.


b.
B409923

Disconnect the connector and detach the clamp from the front pillar RH.


c.
B409924

Disconnect the connector from the rear pillar RH.


d.

Disconnect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.

B409925C01
2.24,1.552 2.448,1.708 0.208,0.156 10 true *1 4.708,1.531 4.938,1.688 0.229,0.156 10 true *2
*1 Front Door Opening Trim Weatherstrip LH *2 Rear Door Opening Trim Weatherstrip LH



e.

Disconnect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.

B409926C01
5.031,1.531 5.26,1.688 0.229,0.156 10 true *1 2.573,1.552 2.781,1.708 0.208,0.156 10 true *2
*1 Front Door Opening Trim Weatherstrip RH *2 Rear Door Opening Trim Weatherstrip RH



f.
B409927

Using a clip remover, remove the 2 clips.


g.
B409928C01
0,0 0,0 false
V113147

Remove in this Direction


Turn the roof headlining assembly diagonally and bend slightly to remove it from the back door.

NOTICE:
·

Make sure wrinkles do not form in the roof headlining assembly during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.




Hide 66423 41.REMOVE FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B409930

Detach the claw and remove the front side rail spacer LH.


Hide 66413B 42.REMOVE FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

a.
B409931

Detach the claw and remove the front side rail spacer RH.


Hide 66424 43.REMOVE REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B409932

Detach the claw and remove the rear side rail spacer LH.


Hide 66414A 44.REMOVE REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

a.
B409933

Detach the claw and remove the rear side rail spacer RH.


Hide 66425A 45.REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

a.
B409934

Detach the claw and remove the rear No. 2 side rail spacer LH.


Hide 66415A 46.REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

a.
B409935

Detach the claw and remove the rear No. 2 side rail spacer RH.