Home › Vehicle Interior › SEAT BELT › REAR NO. 1 SEAT INNER BELT ASSEMBLY(for 60/40 Split Seat Type 60 Side)
RM33K0E _58 Vehicle Interior _043554 SEAT BELT _0229925 REAR NO. 1 SEAT INNER BELT ASSEMBLY(for 60/40 Split Seat Type 60 Side) A

SEAT BELT  REAR NO. 1 SEAT INNER BELT ASSEMBLY(for 60/40 Split Seat Type 60 Side)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·
B394717

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.

·

Replace any other damaged parts as necessary.



PROCEDURE

Hide 73330C 1.INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY RH

a.

w/ Seat Belt Warning System:

i.
B427428C01
1.917,0.896 2.5,0.573 true 1.427,1.542 1.042,1.625 false 2.573,0.5 2.885,0.656 0.313,0.156 10 false *a 0.844,1.542 1.156,1.698 0.313,0.156 10 false *b
*a Band
*b Wire Harness


Connect the rear center seat lap type belt assembly RH to the band as shown in the illustration.


ii.
B427429C01
1.542,1.073 1.25,0.521 1.25,0.521 0.948,0.521 true 1.417,1.083 0.99,1.438 true 0.813,1.396 1.125,1.552 0.313,0.156 10 false *a 0.75,0.438 1.063,0.594 0.313,0.156 10 false *b
*a Slit
*b Wire Harness


Pass the wire harness through the slit.


iii.
B427430

Pass the rear center seat lap type belt assembly RH through the hole of the rear seat cushion cover with pad LH as shown in the illustration.


iv.
B427431C01
1.688,2.021 1.396,1.792 true 1.208,3.469 0.521,3.365 true 1.177,3.729 0.698,4.125 true 1.74,2.031 2.052,2.188 0.313,0.156 10 false *a 0.531,4.125 0.844,4.281 0.313,0.156 10 false *b 0.344,3.229 0.656,3.385 0.313,0.156 10 false *c
*a Protruding Part
*b Wire Harness
*c Anchor Part


Install the rear center seat lap type belt assembly RH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

The anchor part of the rear center seat lap type belt assembly RH must not overlap the protruding part.


NOTICE:
·

The anchor part of the rear center seat lap type belt assembly RH must not overlap the protruding part.

·

Pass the wire harness underneath the anchor part.




v.

Attach the clamp.

B421276



b.

w/o Seat Belt Warning System:

i.
B409116C01
1.365,1.885 1.865,1.74 true 1.906,1.615 2.219,1.771 0.313,0.156 10 false *a
*a Protruding Part
V113147

Install in this Direction


Pass the rear center seat lap type belt assembly RH through the hole of the rear seat cushion cover with pad LH as shown in the illustration.


ii.

Install the rear center seat lap type belt assembly RH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

The anchor part of the rear center seat lap type belt assembly RH must not overlap the protruding part.



iii.
B409117C01
1.625,1.135 0.906,0.646 true 0.708,0.531 1.021,0.688 0.313,0.156 10 true *a
*a Band
V113147

Install in this Direction


Connect the rear center seat lap type belt assembly RH to the band as shown in the illustration.



Hide 73340C 2.INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY LH

a.
B409121C01
0,0 0,0 false
V113147

Install in this Direction


Pass the rear center seat lap type belt assembly LH through the hole of the rear seat cushion cover with pad LH as shown in the illustration.


b.

w/ Seat Belt Warning System:

i.
B409119C01
2.333,1.74 2.604,1.104 2.604,1.104 2.823,1.104 true 2.885,0.979 3.198,1.135 0.313,0.156 10 true *a
*a Protruding Part


Install the rear center seat lap type belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

The anchor part of the rear No. 1 seat inner belt assembly LH must not overlap the protruding part.



ii.

Attach the clamp.

B427432C01
0,0 0,0 false
V100135

Connector
V100136

A


NOTICE:

Pass the wire harness through the frame hole as shown in illustration A.



iii.

Connect the connector.


iv.
B421280C01
0,0 0,0 false
V113147

Install in this Direction


While closing the back of the seat cushion cover with pad as shown in the illustration, pull out the rear seat lock assembly installation part of the rear No. 1 seat lock cable assembly and the rear center seat lap type belt assembly LH from the slit.



c.

w/o Seat Belt Warning System:

i.
B409119C01
2.333,1.74 2.604,1.104 2.604,1.104 2.823,1.104 true 2.885,0.979 3.198,1.135 0.313,0.156 10 true *a
*a Protruding Part


Install the rear center seat lap type belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

The anchor part of the rear No. 1 seat inner belt assembly LH must not overlap the protruding part.



ii.
B403787C01
0,0 0,0 false
V113147

Install in this Direction


While closing the back of the seat cushion cover with pad as shown in the illustration, pull out the rear seat lock assembly installation part of the rear No. 1 seat lock cable assembly from the slit.



d.
B403790C01
0,0 0,0 false
V113147

Install in this Direction


Close the fasteners as shown in the illustration.


e.

Push in the closed fasteners as shown in the illustration.

B410991C01
0,0 0,0 false
V113147

Install in this Direction - -



f.
B403788

Roll up the No. 1 fold seat stopper band assembly toward the rear end of the seat cushion with pad and push it into the seat cushion with pad in the direction indicated by the arrow shown in the illustration.


g.
B403755

While sliding the part in the direction indicated by the arrow shown in the illustration, install the J hook.


Hide 72170 3.INSTALL REAR SEAT OUTER TRACK ASSEMBLY LH

Hide 72190 4.INSTALL REAR SEAT INNER TRACK ASSEMBLY LH

Hide 72201B 5.INSTALL SEAT TRACK HANDLE SUB-ASSEMBLY LH

Hide 72618 11.INSTALL REAR SEATBACK LOCK STRIKER PROTECTOR

Hide 72616A 12.INSTALL REAR SEATBACK LOCK STRIKER COVER LH

Hide 72618 13.INSTALL REAR SEATBACK LOCK STRIKER PROTECTOR

Hide 72616A 14.INSTALL REAR SEATBACK LOCK STRIKER COVER LH

Hide 72526E 15.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH