Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM33K0E _59 Vehicle Exterior _043558 WINDOW / GLASS _0229931 POWER WINDOW CONTROL SYSTEM U

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  TERMINALS OF ECU  


CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/ Smart Entry and Start System)


a.
B187998C07
0.969,0.188 1.354,0.49 0.385,0.302 2.094,0.167 2.479,0.469 0.385,0.302 1.083,0.25 1.396,0.448 0.313,0.198 10 false J5 2.177,0.24 2.49,0.438 0.313,0.198 10 false K14 1.438,0.25 1.75,0.448 0.313,0.198 10 false *A 2.563,0.229 2.875,0.427 0.313,0.198 10 false *B
*A for RHD
*B for LHD


Disconnect the J5*1 or K14*2 power window regulator master switch assembly connector.

·

*1: for RHD

·

*2: for LHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J5-11 (B) - J5-12 (GND) Y - W-B Power supply Always 11 to 14 V
J5-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
K14-11 (B) - K14-12 (GND) Y - W-B Power supply Always 11 to 14 V
K14-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the J5*1 or K14*2 power window regulator master switch assembly connector.

·

*1: for RHD

·

*2: for LHD



d.

Measure the voltage according to the value(s) in the table below.

for RHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
J5-15 (DOWN) - J5-12 (GND) P - W-B Driver door power window motor DOWN output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
J5-20 (UP) - J5-12 (GND) B - W-B Driver door power window motor UP output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V

for LHD
Tester Connection Wiring Color Terminal Description Condition Specified Condition
K14-15 (DOWN) - K14-12 (GND) P - W-B Driver door power window motor DOWN output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pushed halfway down (Manual operation) Below 1 V
K14-20 (UP) - K14-12 (GND) B - W-B Driver door power window motor UP output Ignition switch ON, driver door power window regulator switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, driver door power window regulator switch pulled halfway up (Manual operation) Below 1 V



CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (w/o Smart Entry and Start System)


a.
B276285N16
1.521,0.115 1.927,0.385 0.406,0.271 1.635,0.167 1.948,0.365 0.313,0.198 10 false K13

Disconnect the K13 power window regulator master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
K13-7 (B) - K13-1 (E) LA-GR - W-B IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
K13-1 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the K13 power window regulator master switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
K13-6 (U) - K13-1 (E) B - W-B Driver door power window motor up output Ignition switch ON, driver door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window switch pulled halfway up (Manual operation) Below 1 V
K13-4 (A) - K13-1 (E) SB - W-B Driver door power window motor auto up output Ignition switch ON, driver door power window fully open 11 to 14 V
Ignition switch ON, driver door power window switch fully pulled up (AUTO UP position) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Driver door power window motor auto down output Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window switch fully pushed down (AUTO DOWN position) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
K13-3 (D) - K13-1 (E) P - W-B Driver door power window motor down output Ignition switch ON, driver door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window switch pushed halfway down (Manual operation) Below 1 V
K13-10 (U) - K13-1 (E) LA-R - W-B Front passenger door power window motor up output Ignition switch ON, front passenger door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window switch pulled up (Manual operation) Below 1 V
K13-18 (D) -K13-1 (E) LA-G - W-B Front passenger door power window motor down output Ignition switch ON, front passenger door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window switch pushed down (Manual operation) Below 1 V
K13-12 (U) - K13-1 (E) LA-Y - W-B Rear door LH power window motor up output Ignition switch ON, rear LH door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window switch pulled up (Manual operation) Below 1 V
K13-13 (D) - K13-1 (E) LA-P - W-B Rear door LH power window motor down output Ignition switch ON, rear LH door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window switch pushed down (Manual operation) Below 1 V
K13-15 (U) - K13-1 (E) LA-B - W-B Rear door RH power window motor up output Ignition switch ON, rear RH door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window switch pulled up (Manual operation) Below 1 V
K13-16 (D) - K13-1 (E) LA-V - W-B Rear door RH power window motor down output Ignition switch ON, rear RH door power window switch not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window switch pushed down (Manual operation) Below 1 V



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


a.
B187997N59
1.479,0.302 1.906,0.563 0.427,0.26 1.635,0.365 1.927,0.552 0.292,0.188 10 false J8

Disconnect the J8 front power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

J8-1 (GND) - Body ground LA-W*1 - Body ground
W-B*2 - Body ground
Ground Always Below 1 Ω
J8-2 (B) - Body ground LA-GR*1 - Body ground
GR*2 - Body ground
Power supply Always 11 to 14 V


c.

Reconnect the J8 front power window regulator motor assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
J8-7 (DOWN) - J8-1 (GND) P - LA-W Power window motor DOWN input Ignition switch ON, power window master switch (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully open 11 to 14 V
J8-10 (UP) - J8-1 (GND) B - LA-W Power window motor UP input Ignition switch ON, power window master switch (driver door power window regulator switch) not pushed or pulled 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, power window master switch (driver door power window regulator switch) fully open 11 to 14 V
Ignition switch ON, driver door power window moving, power window master switch (driver door power window regulator switch) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, driver door power window fully closed 11 to 14 V



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Smart Entry and Start System)


a.
B187997N60
1.479,0.302 1.906,0.563 0.427,0.26 1.635,0.365 1.927,0.552 0.292,0.188 10 false K9

Disconnect the K9 front power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
K9-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
K9-2 (B) - Body ground GR - Body ground Power supply Always 11 to 14 V


c.

Reconnect the K9 front power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
K9-4 (AUTO) - K9-1 (GND) L - W-B Power window motor AUTO UP input Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
K9-7 (DOWN) - K9-1 (GND) P - W-B Power window motor DOWN input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pushed down (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
K9-10 (UP) - K9-1 (GND) B - W-B Power window motor UP input Ignition switch ON, power window regulator switch assembly not pushed or pulled 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, front passenger door power window fully open 11 to 14 V
Ignition switch ON, front passenger door power window moving, power window regulator switch assembly fully pulled up (Auto operation) Below 1 V
Ignition switch ON, front passenger door power window fully closed 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Smart Entry and Start System)


a.
B187997N61
1.479,0.302 1.906,0.563 0.427,0.26 1.594,0.365 1.885,0.552 0.292,0.188 10 false M4

Disconnect the M4 rear power window regulator motor assembly LH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
M4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
M4-2 (B) - Body ground L - Body ground Power supply Always 11 to 14 V


c.

Reconnect the M4 rear power window regulator motor assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
M4-4 (AUTO) - M4-1 (GND) R - W-B Power window motor AUTO UP input Ignition switch ON, rear LH door power window fully open 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for Rear LH Door) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for Rear LH Door) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
M4-7 (DOWN) - M4-1 (GND) P - W-B Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly (for Rear LH Door) not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for Rear LH Door) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for Rear LH Door) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
M4-10 (UP) - M4-1 (GND) B - W-B Power window motor UP input Ignition switch ON, rear power window regulator switch assembly (for Rear LH Door) not pushed or pulled 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for Rear LH Door) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, rear LH door power window fully open 11 to 14 V
Ignition switch ON, rear LH door power window moving, rear power window regulator switch assembly (for Rear LH Door) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear LH door power window fully closed 11 to 14 V



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (w/ Smart Entry and Start System)


a.
B187997N62
1.479,0.302 1.906,0.563 0.427,0.26 1.635,0.365 1.927,0.552 0.292,0.188 10 false L4

Disconnect the L4 rear power window regulator motor assembly RH connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
L4-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
L4-2 (B) - Body ground G - Body ground Power supply Always 11 to 14 V


c.

Reconnect the L4 rear power window regulator motor assembly RH connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
L4-4 (AUTO) - L4-1 (GND) R - W-B Power window motor AUTO UP input Ignition switch ON, rear RH door power window fully open 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for Rear RH Door) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Power window motor AUTO DOWN input Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for Rear RH Door) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
L4-7 (DOWN) - L4-1 (GND) P - W-B Power window motor DOWN input Ignition switch ON, rear power window regulator switch assembly (for Rear RH Door) not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for Rear RH Door) pushed halfway down (Manual operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for Rear RH Door) fully pushed down (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
L4-10 (UP) - L4-1 (GND) B - W-B Power window motor UP input Ignition switch ON, rear power window regulator switch assembly (for Rear RH Door) not pushed or pulled 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for Rear RH Door) pulled halfway up (Manual operation) Below 1 V
Ignition switch ON, rear RH door power window fully open 11 to 14 V
Ignition switch ON, rear RH door power window moving, rear power window regulator switch assembly (for Rear RH Door) fully pulled up (Auto operation) Below 1 V
Ignition switch ON, rear RH door power window fully closed 11 to 14 V



CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY ECU


E317657C01
0.594,3.865 0.927,4.104 0.333,0.24 1.99,3.865 2.323,4.104 0.333,0.24 3.458,3.865 3.792,4.104 0.333,0.24 4.844,3.865 5.177,4.104 0.333,0.24 6.198,3.865 6.531,4.104 0.333,0.24 0.594,5.063 0.927,5.302 0.333,0.24 1.969,5.063 2.302,5.302 0.333,0.24 3.333,5.063 3.667,5.302 0.333,0.24 4.729,5.063 5.063,5.302 0.333,0.24 6.198,5.063 6.531,5.302 0.333,0.24 0.604,6.448 0.938,6.688 0.333,0.24 1.938,6.448 2.271,6.688 0.333,0.24 3.375,6.448 3.708,6.688 0.333,0.24 4.833,6.448 5.167,6.688 0.333,0.24 6.208,6.438 6.542,6.677 0.333,0.24 3.344,7.708 3.677,7.948 0.333,0.24 0.104,0.052 0.417,0.292 0.313,0.24 12 false *1 0.75,0.938 1.063,1.135 0.313,0.198 10 false 2L 0.729,1.281 1.042,1.479 0.313,0.198 10 false 2M 0.74,1.667 1.052,1.865 0.313,0.198 10 false 2D 0.74,2.031 1.052,2.229 0.313,0.198 10 false 2K 0.729,2.375 1.042,2.573 0.313,0.198 10 false 2C 0.74,3.115 1.052,3.313 0.313,0.198 10 false 2A 1.281,3.104 1.594,3.302 0.313,0.198 10 false 2B 3.333,0.896 3.49,1.094 0.156,0.198 10 false A 6.375,0.583 6.688,0.781 0.313,0.198 10 false 2Q 6.396,0.927 6.708,1.125 0.313,0.198 10 false 2J 6.385,1.281 6.698,1.479 0.313,0.198 10 false 2P 6.385,1.656 6.698,1.854 0.313,0.198 10 false 2N 6.385,2 6.698,2.198 0.313,0.198 10 false 2G 6.396,2.375 6.708,2.573 0.313,0.198 10 false 2H 5.865,2.927 6.177,3.125 0.313,0.198 10 false 2F 6.375,2.99 6.688,3.188 0.313,0.198 10 false 2E 0.698,3.906 1.01,4.104 0.313,0.198 10 false 2L 2.063,3.906 2.375,4.104 0.313,0.198 10 false 2M 3.552,3.896 3.865,4.094 0.313,0.198 10 false 2D 4.917,3.906 5.229,4.104 0.313,0.198 10 false 2K 6.271,3.906 6.594,4.125 0.323,0.219 10 false 2C 0.667,5.094 0.979,5.292 0.313,0.198 10 false 2A 2.042,5.094 2.354,5.292 0.313,0.198 10 false 2B 3.406,5.104 3.719,5.302 0.313,0.198 10 false 2Q 4.823,5.094 5.135,5.292 0.313,0.198 10 false 2J 6.292,5.104 6.604,5.302 0.313,0.198 10 false 2P 0.688,6.479 1,6.677 0.313,0.198 10 false 2N 2.021,6.479 2.333,6.677 0.313,0.198 10 false 2G 3.458,6.479 3.771,6.677 0.313,0.198 10 false 2H 4.927,6.479 5.24,6.677 0.313,0.198 10 false 2F 6.292,6.469 6.604,6.667 0.313,0.198 10 false 2E 3.469,7.74 3.625,7.938 0.156,0.198 10 false A
*1 Instrument Panel Junction Block Assembly - -


E317658C01
2.24,3.344 2.625,3.583 0.385,0.24 4.563,3.344 4.948,3.583 0.385,0.24 0.125,0.073 0.438,0.365 0.313,0.292 12 false *1 5.76,1.531 6.219,1.729 0.458,0.198 10 false G34 5.76,2.021 6.219,2.219 0.458,0.198 10 false G33 2.292,3.375 2.75,3.573 0.458,0.198 10 false G34 4.635,3.375 5.094,3.573 0.458,0.198 10 false G33
*1 Body ECU - -


a.

Remove the body ECU from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
A-1 (GND) - Body ground None - Body ground Ground Always Below 1 Ω
A-6 (BECU) - Body ground None - Body ground Battery power supply Always 11 to 14 V
A-7 (IG) - Body ground None - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


c.

Install the body ECU to the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>INSTALLATION


d.

Measure the voltage and waveform according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
G33-14 (PCTY) - Body ground LG - Body ground Front door courtesy light switch assembly LH input Front door LH open Below 1 V
Front door LH closed Pulse generation
2L-4 (DCTY) - Body ground R - Body ground Front door courtesy light switch assembly RH input Front door RH open Below 1 V
Front door RH closed Pulse generation