Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM33K0E _59 Vehicle Exterior _043558 WINDOW / GLASS _0229931 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Remote Up / Down Function does not Operate  


DESCRIPTION

When the ignition switch ON, the power window regulator master switch assembly sends remote up and down signals to each power window regulator motor assembly via LIN communication.

CAUTION / NOTICE / HINT

NOTICE:
·

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
·

*1: for RHD

·

*2: for LHD


a.

Disconnect the G33 body ECU connector.


b.

Disconnect the J5*1 or K14*2 power window regulator master switch connector.


c.

Disconnect the K9*1 front power window regulator motor assembly LH connector.


d.

Disconnect the J8*1 front power window regulator motor assembly RH connector.


e.

Disconnect the M4 rear power window regulator motor assembly LH connector.


f.

Disconnect the L4 rear power window regulator motor assembly RH connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-3 (LIN2) - J5-17 (LIN1)*1 Always Below 1 Ω
G33-3 (LIN2) - K14-17 (LIN1)*2 Always Below 1 Ω
G33-3 (LIN2) - K9-9 (LIN)*1 Always Below 1 Ω
G33-3 (LIN2) - J-9 (LIN)*2 Always Below 1 Ω
G33-3 (LIN2) - M4-9 (LIN) Always Below 1 Ω
G33-3 (LIN2) - L4-9 (LIN) Always Below 1 Ω
G33-3 (LIN2) - Body ground Always 10 kΩ or higher
J5-17 (LIN1) - Body ground*1 Always 10 kΩ or higher
K14-17 (LIN1) - Body ground*2 Always 10 kΩ or higher
K9-9 (LIN) - Body ground*1 Always 10 kΩ or higher
J8-9 (LIN) - Body ground*2 Always 10 kΩ or higher
M4-9 (LIN) - Body ground Always 10 kΩ or higher
L4-9 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Replace the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Check that the remote up and down functions using the power window regulator master switch assembly can operate all the power windows.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK

OK:

Remote up and down functions are normal.



Result:
Proceed to
OK
NG



OK

END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG