Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS
RM33K0E _59 Vehicle Exterior _043558 WINDOW / GLASS _0229938 BACK DOOR GLASS A

WINDOW / GLASS  BACK DOOR GLASS  REMOVAL  


PROCEDURE

Hide 67939B 1.REMOVE CENTER BACK DOOR GARNISH

Hide 67938A 2.REMOVE BACK DOOR SIDE GARNISH LH

Hide 67937B 3.REMOVE BACK DOOR SIDE GARNISH RH

Hide 74811D 4.REMOVE DOOR PULL HANDLE

Hide 67750 5.REMOVE BACK DOOR TRIM BOARD ASSEMBLY

Hide 67847A 6.REMOVE BACK DOOR SERVICE HOLE COVER (w/ Cover)

Hide 85292A 7.REMOVE REAR WIPER ARM HEAD CAP

Hide 8.REMOVE REAR WIPER ARM AND BLADE ASSEMBLY

Hide 85110R 9.REMOVE REAR WIPER MOTOR ASSEMBLY

Hide 85143R 10.REMOVE REAR WIPER MOTOR GROMMET

Hide 64886B 11.REMOVE BACK DOOR GLASS CHANNEL LH

Hide 64885C 12.REMOVE BACK DOOR GLASS CHANNEL RH

HINT:

Use the same procedure as for the LH side.


Hide 13.REMOVE REAR SPOILER ASSEMBLY

Hide 68131 14.REMOVE BACK DOOR GLASS

NOTICE:
·

Be careful not to damage the back door glass when cutting as the back door glass spacers are installed to the back door glass.


·

The back door glass may fall while performing this procedure. Therefore, use suction cups to hold the back door glass from the outside of the vehicle.



a.
B409218C01
0,0 0,0 false
V100155

Protective Tape


Put protective tape on the back door panel around the back door glass.

NOTICE:

When separating the back door glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.



b.
B409219C01
1.771,0.51 2.188,0.198 false 2.198,0.115 2.51,0.271 0.313,0.156 10 false *a
*a Matchmark


When reusing back door glass:

i.

Place adhesive tape on the back door glass and body panel and use a pen to place matchmarks for installation.


ii.

Install the suction cups to the back door glass.



c.
B409220C01
0,0 0,0 false
V100135

Bolt
V100136

Connector


Detach the clamp and claw.


d.

Disconnect the connector and remove the bolt.


e.
B409221C01
0.563,0.677 1,0.313 true 2.875,0.677 2.469,0.354 true 0.396,1.323 0.75,1.688 true 3.021,1.323 2.646,1.75 true 0.125,1.385 0.219,1.854 0.219,1.854 0.26,1.594 false 1.094,0.229 1.406,0.385 0.313,0.156 10 false *1 0.833,1.719 1.156,1.875 0.323,0.156 10 false *2 0.167,1.896 0.479,2.052 0.313,0.156 10 false *a 2.458,1.719 2.771,1.917 0.313,0.198 10 false *2 2.292,0.25 2.604,0.448 0.313,0.198 10 false *1
*1 Back Window Glass Clip
*2 Back Window Glass Spacer
*a Piano Wire


Insert a piano wire (approximately 0.6 mm) at the locations shown in the illustration.


f.

Tie objects that can serve as handles (for example, wooden blocks) to the wire ends.


g.

Pull on the ends of the piano wire alternately and leave the back door glass spacers when cutting through the adhesive.

NOTICE:
·

Do not forcefully brush the piano wire against the back door glass.


·

Be careful as the piano wire will break if it crosses itself.




h.

Using suction cups, remove the back door glass.

NOTICE:

Make sure that the back door glass does not fall.