Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART)
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P167A  Lost Communication with Injector #1  P167B  Lost Communication with Injector #2  P167C  Lost Communication with Injector #3  P167D  Lost Communication with Injector #4  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P167A Lost Communication with Injector #1 Communication between the ECM and injector assembly is lost for 4 seconds or more.
(1 trip detection logic)
·

No. 1 Injector assembly

·

Harness and connector


Comes on DTC stored
P167B Lost Communication with Injector #2 Communication between the ECM and injector assembly is lost for 4 seconds or more.
(1 trip detection logic)
·

No. 2 Injector assembly

·

Harness and connector


Comes on DTC stored
P167C Lost Communication with Injector #3 Communication between the ECM and injector assembly is lost for 4 seconds or more.
(1 trip detection logic)
·

No. 3 Injector assembly

·

Harness and connector


Comes on DTC stored
P167D Lost Communication with Injector #4 Communication between the ECM and injector assembly is lost for 4 seconds or more.
(1 trip detection logic)
·

No. 4 Injector assembly

·

Harness and connector


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P167A
P167B
P167C
P167D
Engine switch on (IG) for 3 minutes or more

MONITOR DESCRIPTION

If the ECM detects that there is a communication problem with an injector for a certain amount of time continuously, it illuminates the MIL.

A DTC is assigned for each cylinder. However, the cylinders cannot be distinguished. If there is no problem with the communication line, replace all the injector assemblies.

A379944E01
2.969,0.938 4.333,0.479 true 2.969,0.938 6.292,0.844 true 0.573,3.906 1.031,4.104 0.458,0.198 10 false ECM 1.01,2.792 1.469,2.99 0.458,0.198 10 false CINJ 4.823,1.042 6.344,1.281 1.521,0.24 10 false No. 1 Injector Assembly 5.552,2.208 7.073,2.448 1.521,0.24 10 false No. 2 Injector Assembly 5.177,3.375 6.698,3.615 1.521,0.24 10 false No. 3 Injector Assembly 4.771,4.635 6.292,4.875 1.521,0.24 10 false No. 4 Injector Assembly 1.24,0.823 3.021,1.177 1.781,0.354 10 false Stores DTC P167A, P167B, P167C, P167D 5.802,0.219 6.323,0.396 0.521,0.177 10 false CINJ 4.583,1.427 5.104,1.604 0.521,0.177 10 false CIJ2 4.208,2.656 4.729,2.833 0.521,0.177 10 false CIJ3 3.969,3.896 4.49,4.073 0.521,0.177 10 false CIJ4 2.302,1.844 3.854,2.083 1.552,0.24 10 false INJ Communication Line 1.802,3.354 3.271,3.771 1.469,0.417 10 false Stores DTC P167A, P167B, P167C, P167D

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P167A, P167B, P167C and P167D are output A
P13A1, P13A2, P13A3, P13A6, P13A7, P13A8, P13AB, P13AC, P13AD, P13B1, P13B2, P13B3, P13C3, P13C8, P13CD, P13D3 and P167A, P167B, P167C, P167D are output B




A

2.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)

B

2.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)
a.

Disconnect the injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C133-5 (CINJ) - C41-16 (CINJ) Always Below 1 Ω
C134-5 (CIJ2) - C41-16 (CINJ) Always Below 1 Ω
C135-5 (CIJ3) - C41-16 (CINJ) Always Below 1 Ω
C136-5 (CIJ4) - C41-16 (CINJ) Always Below 1 Ω
C133-5 (CINJ) or C41-16 (CINJ) - Body ground and other terminals Always 200 kΩ or higher
C134-5 (CIJ2) or C41-16 (CINJ) - Body ground and other terminals Always 200 kΩ or higher
C135-5 (CIJ3) or C41-16 (CINJ) - Body ground and other terminals Always 200 kΩ or higher
C136-5 (CIJ4) or C41-16 (CINJ) - Body ground and other terminals Always 200 kΩ or higher



d.

Reconnect the injector assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT INJECTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INJECTOR ASSEMBLY
a.

Disconnect the injector assembly connector.


A321482C01
1.208,0.583 1.438,0.792 0.229,0.208 10 false *1 2.26,1.375 2.49,1.583 0.229,0.208 10 false *a
*1 Ohmmeter
*a Component without harness connected
(Injector Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (CINJ) - 1 (EIJ1) Always 600 to 1400 kΩ
5 (CIJ2) - 1 (EIJ2) Always 600 to 1400 kΩ
5 (CIJ3) - 1 (EIJ3) Always 600 to 1400 kΩ
5 (CIJ4) - 1 (EIJ4) Always 600 to 1400 kΩ


HINT:
·

If there is an injector assembly that is outside the specified range, only replace that injector assembly.

·

Even when the resistance is within the specified range, the injector assembly may be malfunctioning. Therefore, if all of the injector assemblies are within the specified range, replace all of the injector assemblies.




c.

Reconnect the injector assembly connector.


Result:
Proceed to
NEXT



NEXT

4.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
4.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and GTS on.


c.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the engine switch off and wait for at least 30 seconds


e.

Turn the engine switch on (IG) for 3 minutes or more.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END