Home › Engine / Hybrid System › 1GD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART)
RM33K0E _51 Engine / Hybrid System _043518 1GD-FTV ENGINE CONTROL _0245023 ECD SYSTEM(for i-ART) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P13A1  Fuel Pressure Sensor Circuit Low #1(Sub CPU)  P13A2  Fuel Pressure Sensor Circuit High #1(Sub CPU)  P13A3  Fuel Pressure Sensor Circuit Range/Performance #1  P13A6  Fuel Pressure Sensor Circuit Low #2(Sub CPU)  P13A7  Fuel Pressure Sensor Circuit High #2(Sub CPU)  P13A8  Fuel Pressure Sensor Circuit Range/Performance #2  P13AB  Fuel Pressure Sensor Circuit Low #3(Sub CPU)  P13AC  Fuel Pressure Sensor Circuit High #3(Sub CPU)  P13AD  Fuel Pressure Sensor Circuit Range/Performance #3  P13B1  Fuel Pressure Sensor Circuit Low #4(Sub CPU)  P13B2  Fuel Pressure Sensor Circuit High #4(Sub CPU)  P13B3  Fuel Pressure Sensor Circuit Range/Performance #4  P13E1  Fuel Pressure Sensor Circuit Low #1(Main CPU)  P13E2  Fuel Pressure Sensor Circuit High #1(Main CPU)  P13E6  Fuel Pressure Sensor Circuit Low #4(Main CPU)  P13E7  Fuel Pressure Sensor Circuit High #4(Main CPU)  


DESCRIPTION

A fuel pressure sensor, which is built into the injector assembly, converts the fuel pressure to an electrical signal which is sent to the ECM. Based on this signal, the ECM controls the fuel supply pump assembly and maintains the fuel pressure in the common rail assembly at the target pressure. A semiconductor is used in the fuel pressure sensor. The semiconductor changes its internal resistance value according to the fuel pressure, and as a result, the output voltage is proportional to the fuel pressure.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P13A1 Fuel Pressure Sensor Circuit Low #1(Sub CPU) Sub CPU Side:
The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13A2 Fuel Pressure Sensor Circuit High #1(Sub CPU) Sub CPU Side:
The output voltage of the fuel pressure sensor is 4.84 V or higher for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13A3 Fuel Pressure Sensor Circuit Range/Performance #1 The output of the fuel pressure sensor differs by 33 MPa or more compared to other cylinders for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13A6 Fuel Pressure Sensor Circuit Low #2(Sub CPU) Sub CPU Side:
The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13A7 Fuel Pressure Sensor Circuit High #2(Sub CPU) Sub CPU Side:
The output voltage of the fuel pressure sensor is 4.84 V or higher for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13A8 Fuel Pressure Sensor Circuit Range/Performance #2 The output of the fuel pressure sensor differs by 33 MPa or more compared to other cylinders for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13AB Fuel Pressure Sensor Circuit Low #3(Sub CPU) Sub CPU Side:
The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13AC Fuel Pressure Sensor Circuit High #3(Sub CPU) Sub CPU Side:
The output voltage of the fuel pressure sensor is 4.84 V or higher for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13AD Fuel Pressure Sensor Circuit Range/Performance #3 The output of the fuel pressure sensor differs by 33 MPa or more compared to other cylinders for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13B1 Fuel Pressure Sensor Circuit Low #4(Sub CPU) Sub CPU Side:
The output voltage of the fuel pressure sensor is 0.55 V or less for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13B2 Fuel Pressure Sensor Circuit High #4(Sub CPU) Sub CPU Side:
The output voltage of the fuel pressure sensor is 4.84 V or higher for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13B3 Fuel Pressure Sensor Circuit Range/Performance #4 The output of the fuel pressure sensor differs by 33 MPa or more compared to other cylinders for 0.5 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13E1 Fuel Pressure Sensor Circuit Low #1(Main CPU) Main CPU Side:
The fuel pressure sensor output voltage of injector #1 and/or #4 is below 0.5 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13E2 Fuel Pressure Sensor Circuit High #1(Main CPU) Main CPU Side:
The fuel pressure sensor output voltage of injector #1 and/or #4 is higher than 4.85 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13E6 Fuel Pressure Sensor Circuit Low #4(Main CPU) Main CPU Side:
The fuel pressure sensor output voltage of injector #1 and/or #4 is below 0.5 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13E7 Fuel Pressure Sensor Circuit High #4(Main CPU) Main CPU Side:
The fuel pressure sensor output voltage of injector #1 and/or #4 is higher than 4.85 V for 3 seconds or more.
(1 trip detection logic)
·

Open or short in fuel pressure sensor (built into injector assembly) circuit

·

Fuel pressure sensor (built into injector assembly)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P13A1
P13A2
P13A6
P13A7
P13AB
P13AC
P13B1
P13B2
·

Fuel Pressure #1

·

Fuel Pressure #2

·

Fuel Pressure #3

·

Fuel Pressure #4


P13E1
P13E2
P13E6
P13E7
P13A3
P13A8
P13AD
P13B3

HINT:
·

Check Common Rail Pressure and compare it to Target Common Rail Pressure in the Data List by entering the following menus: Powertrain / Engine / Data List / Common Rail Pressure, Target Common Rail Pressure. Under stable conditions, the difference between Common Rail Pressure and Target Common Rail Pressure is 5000 kPa or less.

·

For more information on the fuel pressure sensor and common rail system, refer to System Description (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>SYSTEM DESCRIPTION).

·

If DTC P13A1, P13A2, P13A6, P13A7, P13AB, P13AC, P13B1, P13B2, P13E1, P13E2, P13E6 and/or P13E7 is stored, the following symptom may appear:

·

Lack of power due to accelerator restriction performed by fail-safe function


·

If DTC P13A1, P13A2, P13A6, P13A7, P13AB, P13AC, P13B1, P13B2, P13E1, P13E2, P13E6 and/or P13E7 is stored, "Common Rail Pressure" always displays -53000 kPa or 255992 kPa.



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P13A1
P13A2
P13A6
P13A7
P13AB
P13AC
P13B1
P13B2
Engine switch on (IG) for 1 second or more
P13E1
P13E2
P13E6
P13E7
Engine switch on (IG) for 8 seconds or more
P13A3
P13A8
P13AD
P13B3
After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds

MONITOR DESCRIPTION

A379943E01
1.365,4.906 3.552,5.333 true 3.75,2.448 4.135,0.458 4.135,0.458 4.281,0.458 true 1.344,5.417 1.802,5.615 0.458,0.198 10 false ECM 4.719,3.552 6.396,3.792 1.677,0.24 10 false No. 2 Injector Assembly 4.688,3.865 6.615,4.094 1.927,0.229 10 false No. 3 Injector Assembly 4.677,4.177 6.604,4.406 1.927,0.229 10 false No. 4 Injector Assembly 5.531,4.781 7.063,5.063 1.531,0.281 10 false No. 1 Injector Assembly 4.385,0.292 6.635,1.313 2.25,1.021 10 false Stores P13A1, P13A2, P13A6, P13A7, P13AB, P13AC, P13B1, P13B2, P13E1, P13E2, P13E6, P13E7 1.104,1.073 2.125,1.292 1.021,0.219 10 false Main CPU 0.958,1.729 1.417,1.927 0.458,0.198 10 false #1 1.115,2.552 2.375,2.75 1.26,0.198 10 false Sub CPU 1.74,2.896 2.198,3.094 0.458,0.198 10 false #1 1.74,3.531 2.198,3.729 0.458,0.198 10 false #2 1.74,3.854 2.198,4.052 0.458,0.198 10 false #3 1.74,4.167 2.198,4.365 0.458,0.198 10 false #4 3.625,5.302 6.167,5.521 2.542,0.219 10 false Stores P13E1, P13E2, P13E6, P13E7 2.25,2.365 2.594,2.542 0.344,0.177 10 false 5 V 2.781,2.698 3.125,2.875 0.344,0.177 10 false VIJ1 2.781,3.021 3.125,3.198 0.344,0.177 10 false PIJ1 2.781,3.333 3.125,3.51 0.344,0.177 10 false EIJ1 2.76,3.656 3.104,3.833 0.344,0.177 10 false PIJ2 2.75,3.969 3.094,4.146 0.344,0.177 10 false PIJ3 2.75,4.292 3.146,4.469 0.396,0.177 10 false PIJ4 0.958,1.385 1.417,1.583 0.458,0.198 10 false #4

P13A1, P13A2, P13A6, P13A7, P13AB, P13AC, P13B1, P13B2, P13E1, P13E2, P13E6 and/or P13E7 (Open or short in fuel pressure sensor circuit):

If the fuel pressure sensor output voltage is outside of the standard range due to an open or short in the fuel pressure sensor circuit, DTCs are stored.

If a DTC is stored, the ECM enters fail-safe mode, and engine output is limited only if 2 or more circuits are malfunctioning. The ECM continues operating in fail-safe mode until the engine switch is turned off.

The No. 1 injector assembly and No. 4 injector assembly have separate circuits inside the ECU and a fuel pressure sensor value is input to both the Main CPU and Sub CPU.

HINT:

When there is an open circuit in EIJ or VIJ, DTC P13E2 and P13A2 are output at the same time.

If only one of them are output, there may be an open in the internal circuit of the ECM.



WIRING DIAGRAM

A379947E02
1.875,5.292 2.49,5.49 0.615,0.198 10 false C135 1.865,5.469 4.833,5.708 2.969,0.24 10 false Fuel Pressure Sensor (No. 3 Injector Assembly) 1.885,7.146 2.5,7.344 0.615,0.198 10 false C136 1.875,7.313 4.844,7.552 2.969,0.24 10 false Fuel Pressure Sensor (No. 4 Injector Assembly) 1.865,3.458 2.479,3.656 0.615,0.198 10 false C134 1.885,1.604 2.5,1.802 0.615,0.198 10 false C133 1.875,1.76 4.844,2 2.969,0.24 10 false Fuel Pressure Sensor (No. 1 Injector Assembly) 1.854,3.615 4.823,3.854 2.969,0.24 10 false Fuel Pressure Sensor (No. 2 Injector Assembly) 2.896,0.875 3.51,1.073 0.615,0.198 10 false PIJ1 2.896,1.26 3.51,1.458 0.615,0.198 10 false EIJ1 2,0.885 2.615,1.083 0.615,0.198 10 false CINJ 5.885,0.469 6.5,0.667 0.615,0.198 10 false VIJ1 5.885,0.854 6.5,1.052 0.615,0.198 10 false PIJ1 5.865,7.76 6.479,7.958 0.615,0.198 10 false CINJ 2,2.729 2.615,2.927 0.615,0.198 10 false CIJ2 2,4.615 2.615,4.813 0.615,0.198 10 false CIJ3 1.99,6.458 2.604,6.656 0.615,0.198 10 false CIJ4 2.896,0.469 3.51,0.667 0.615,0.198 10 false VIJ1 5.875,1.271 6.49,1.469 0.615,0.198 10 false EIJ1 2.896,3.115 3.51,3.313 0.615,0.198 10 false EIJ2 2.885,4.969 3.5,5.167 0.615,0.198 10 false EIJ3 2.875,6.823 3.49,7.021 0.615,0.198 10 false EIJ4 2.896,2.719 3.51,2.917 0.615,0.198 10 false PIJ2 2.885,4.573 3.5,4.771 0.615,0.198 10 false PIJ3 2.875,6.427 3.49,6.625 0.615,0.198 10 false PIJ4 2.906,2.333 3.521,2.531 0.615,0.198 10 false VIJ2 2.885,4.156 3.5,4.354 0.615,0.198 10 false VIJ3 2.885,6.021 3.5,6.219 0.615,0.198 10 false VIJ4 5.896,2.344 6.51,2.542 0.615,0.198 10 false VIJ2 5.885,2.719 6.5,2.917 0.615,0.198 10 false PIJ2 5.885,3.115 6.5,3.313 0.615,0.198 10 false EIJ2 5.885,4.188 6.5,4.385 0.615,0.198 10 false VIJ3 5.875,4.583 6.49,4.781 0.615,0.198 10 false PIJ3 5.875,4.99 6.49,5.188 0.615,0.198 10 false EIJ3 5.885,6.042 6.5,6.24 0.615,0.198 10 false VIJ4 5.875,6.448 6.49,6.646 0.615,0.198 10 false PIJ4 5.875,6.833 6.49,7.031 0.615,0.198 10 false EIJ4 5.5,0.469 6.115,0.667 0.615,0.198 10 false C40 5.5,0.865 6.115,1.063 0.615,0.198 10 false C40 5.5,1.26 6.115,1.458 0.615,0.198 10 false C40 5.563,0.281 6.177,0.479 0.615,0.198 10 false 28 5.563,0.677 6.177,0.875 0.615,0.198 10 false 18 5.563,1.083 6.177,1.281 0.615,0.198 10 false 19 5.5,2.313 6.115,2.51 0.615,0.198 10 false C41 5.5,2.708 6.115,2.906 0.615,0.198 10 false C41 5.5,3.115 6.115,3.313 0.615,0.198 10 false C41 5.5,4.177 6.115,4.375 0.615,0.198 10 false C41 5.49,4.573 6.104,4.771 0.615,0.198 10 false C41 5.49,4.969 6.104,5.167 0.615,0.198 10 false C41 5.49,6.031 6.104,6.229 0.615,0.198 10 false C41 5.49,6.427 6.104,6.625 0.615,0.198 10 false C41 5.5,6.823 6.115,7.021 0.615,0.198 10 false C41 5.49,7.729 6.104,7.927 0.615,0.198 10 false C41 6.219,8.26 6.833,8.458 0.615,0.198 10 false ECM 5.563,2.125 6.177,2.323 0.615,0.198 10 false 24 5.542,7.563 6.156,7.76 0.615,0.198 10 false 16 5.552,2.521 6.167,2.719 0.615,0.198 10 false 29 5.563,2.927 6.177,3.125 0.615,0.198 10 false 30 5.552,3.979 6.167,4.177 0.615,0.198 10 false 33 5.552,4.396 6.167,4.594 0.615,0.198 10 false 26 5.552,4.792 6.167,4.99 0.615,0.198 10 false 25 5.552,5.844 6.167,6.042 0.615,0.198 10 false 22 5.552,6.24 6.167,6.438 0.615,0.198 10 false 23 5.542,6.635 6.156,6.833 0.615,0.198 10 false 21 3.26,0.594 3.438,0.813 0.177,0.219 10 false 2 3.26,0.99 3.438,1.208 0.177,0.219 10 false 4 3.26,1.396 3.438,1.615 0.177,0.219 10 false 1 1.792,1 1.969,1.219 0.177,0.219 10 false 5 1.813,2.844 1.99,3.063 0.177,0.219 10 false 5 1.802,4.719 1.979,4.938 0.177,0.219 10 false 5 1.802,6.563 1.979,6.781 0.177,0.219 10 false 5 3.26,2.427 3.438,2.646 0.177,0.219 10 false 2 3.24,4.302 3.417,4.521 0.177,0.219 10 false 2 3.26,6.135 3.438,6.354 0.177,0.219 10 false 2 3.26,3.229 3.438,3.448 0.177,0.219 10 false 1 3.25,5.115 3.427,5.333 0.177,0.219 10 false 1 3.25,6.938 3.427,7.156 0.177,0.219 10 false 1 3.26,2.833 3.438,3.052 0.177,0.219 10 false 4 3.25,4.688 3.427,4.906 0.177,0.219 10 false 4 3.26,6.531 3.438,6.75 0.177,0.219 10 false 4 4.74,0.313 4.917,0.531 0.177,0.219 10 false * 4.719,2.156 4.896,2.375 0.177,0.219 10 false * 4.729,4.01 4.906,4.229 0.177,0.219 10 false * 4.698,5.854 4.875,6.073 0.177,0.219 10 false * 0.521,8.135 1.292,8.344 0.771,0.208 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
"Fuel pressure sensor circuit DTC" and "Injector Internal EEPROM Malfunction circuit DTC" are output* A
Except above B


HINT:
·

*: Fuel pressure sensor circuit DTC and Injector Internal EEPROM Malfunction circuit DTC:

Fuel pressure sensor circuit DTC: P13A3, P13A8, P13AD, P13B3.

Injector Internal EEPROM Malfunction circuit DTC: P168A, P168B, P168C, P168D.

·

When there is an injector internal EEPROM malfunction, fuel pressure sensor circuit range/performance and fuel temperature sensor circuit range/performance DTCs are output at the same time.

For example, when P168A is output, P13A3 and P13C3 are output together.





A

GO TO INTERNAL EEPROM MALFUNCTION CIRCUIT

B

2.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
2.CHECK ECM (FUEL PRESSURE SENSOR VOLTAGE)
a.
A378120C07
1.813,0.521 2.208,0.792 0.396,0.271 1.26,0.521 1.656,0.792 0.396,0.271 0.573,2.583 1.615,1.635 true 1.948,1.635 2.583,0.594 2.583,0.594 2.708,0.594 true 2.313,2.583 1.906,1.688 true 2.719,0.156 2.635,0.156 2.635,0.156 1.865,1.635 true 1.781,1.688 1.646,3.083 1.646,3.083 1.51,3.083 true 1.823,1.635 1.99,3.073 1.99,3.073 2.135,3.073 true 1.99,1.625 2.5,0.938 2.5,0.938 2.604,0.938 true 1.188,2.583 1.656,1.688 true 1.333,0.583 1.792,0.781 0.458,0.198 10 false C40 1.885,0.594 2.344,0.792 0.458,0.198 10 false C41 0.333,2.594 0.979,2.823 0.646,0.229 10 false 19 (EIJ1) 0.99,2.604 1.635,2.813 0.646,0.208 10 false 28 (VIJ1) 2.115,2.594 2.76,2.802 0.646,0.208 10 false 30 (EIJ2) 2.781,0.083 3.375,0.281 0.594,0.198 10 false 24 (VIJ2) 2.208,2.99 2.854,3.219 0.646,0.229 10 false 25 (EIJ3) 2.75,0.521 3.365,0.74 0.615,0.219 10 false 22 (VIJ4) 0.948,3 1.594,3.208 0.646,0.208 10 false 33 (VIJ3) 2.646,0.865 3.292,1.094 0.646,0.229 10 false 21 (EIJ4) 0.271,0.188 0.729,0.385 0.458,0.198 10 false *a
*a Component with harness connected
(ECM)


Disconnect the injector assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C40-28 (VIJ1) - C40-19 (EIJ1) Engine switch on (IG) 4.5 to 5.5 V
C41-24 (VIJ2) - C41-30 (EIJ2) Engine switch on (IG) 4.5 to 5.5 V
C41-33 (VIJ3) - C41-25 (EIJ3) Engine switch on (IG) 4.5 to 5.5 V
C41-22 (VIJ4) - C41-21 (EIJ4) Engine switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)

NG

6.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)
a.

Disconnect the injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C133-2 (VIJ1) - C40-28 (VIJ1) Always Below 1 Ω
C133-4 (PIJ1) - C40-18 (PIJ1) Always Below 1 Ω
C133-1 (EIJ1) - C40-19 (EIJ1) Always Below 1 Ω
C134-2 (VIJ2) - C41-24 (VIJ2) Always Below 1 Ω
C134-4 (PIJ2) - C41-29 (PIJ2) Always Below 1 Ω
C134-1 (EIJ2) - C41-30 (EIJ2) Always Below 1 Ω
C135-2 (VIJ3) - C41-33 (VIJ3) Always Below 1 Ω
C135-4 (PIJ3) - C41-26 (PIJ3) Always Below 1 Ω
C135-1 (EIJ3) - C41-25 (EIJ3) Always Below 1 Ω
C136-2 (VIJ4) - C41-22 (VIJ4) Always Below 1 Ω
C136-4 (PIJ4) - C41-23 (PIJ4) Always Below 1 Ω
C136-1 (EIJ4) - C41-21 (EIJ4) Always Below 1 Ω
C133-4 (PIJ1) or C40-18 (PIJ1) - Body ground and other terminals Always 10 kΩ or higher
C133-1 (EIJ1) or C40-19 (EIJ1) - Body ground and other terminals Always 10 kΩ or higher
C134-4 (PIJ2) or C41-29 (PIJ2) - Body ground and other terminals Always 10 kΩ or higher
C134-1 (EIJ2) or C41-30 (EIJ2) - Body ground and other terminals Always 10 kΩ or higher
C135-4 (PIJ3) or C41-26 (PIJ3) - Body ground and other terminals Always 10 kΩ or higher
C135-1 (EIJ3) or C41-25 (EIJ3) - Body ground and other terminals Always 10 kΩ or higher
C136-4 (PIJ4) or C41-23 (PIJ4) - Body ground and other terminals Always 10 kΩ or higher
C136-1 (EIJ4) or C41-21 (EIJ4) - Body ground and other terminals Always 10 kΩ or higher



d.

Reconnect the injector assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
a.

Replace the injector assembly of the cylinder relevant to the DTC.

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 61
HINT:

Perform the following when there are DTCs which are not cleared.

1.

Turn the engine switch off for 30 seconds or more.

2.

Turn the engine switch on (IG) for 8 seconds or more.

3.

Enter the following menus: Powertrain / Engine / Trouble Codes / Clear.

4.

Check that all DTCs have been cleared.




c.

Turn the engine switch off and wait for at least 30 seconds.


d.

Turn the engine switch on (IG) for 8 seconds or more.


e.

Start the engine.


f.

After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END