Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › from 2016.07
RM33K0E _58 Vehicle Interior _043548 THEFT DETERRENT / KEYLESS ENTRY _0224644 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Ignition Switch Circuit  


DESCRIPTION

The body ECU determines the ignition switch position (LOCK, ACC, ON) based on signals from the IG or ACC circuit.

WIRING DIAGRAM

B405276E04
0.01,0.573 1.844,0.771 1.833,0.198 10 false from Battery 3.854,3.083 5.906,3.625 2.052,0.542 10 false Instrument Panel Junction Block Assembly 5.917,3.094 7.156,3.615 1.24,0.521 10 false A 5.917,3.25 7.156,3.771 1.24,0.521 10 false Body ECU 5.927,2.688 7.156,3.24 1.229,0.552 10 false GND 5.927,1.896 7.156,2.448 1.229,0.552 10 false IG 5.729,1.792 7.156,2.344 1.427,0.552 10 false 7 5.729,2.604 7.156,3.156 1.427,0.552 10 false 1 4.396,2.698 5.625,3.25 1.229,0.552 10 false 2J 4.438,2.521 5.667,3.073 1.229,0.552 10 false 5 3.677,1.896 4.906,2.448 1.229,0.552 10 false 2D 3.656,1.323 4.885,1.875 1.229,0.552 10 false 2D 3.708,1.719 4.938,2.271 1.229,0.552 10 false 5 3.708,1.135 4.938,1.688 1.229,0.552 10 false 7 3.667,0.604 4.896,1.156 1.229,0.552 10 false 2E 3.708,0.417 4.938,0.969 1.229,0.552 10 false 1 4.573,0.75 5.802,1.302 1.229,0.552 10 false IG1 NO.4 1.073,1.094 3.375,1.615 2.302,0.521 10 false Ignition or Starter Switch Assembly 1.083,0.927 3.385,1.448 2.302,0.521 10 false G133 1.438,0.49 3.74,1.01 2.302,0.521 10 false AM1 2.177,0.5 4.479,1.021 2.302,0.521 10 false IG1 2.479,0.49 4.781,1.01 2.302,0.521 10 false 8 1.281,0.5 3.583,1.021 2.302,0.521 10 false 5

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

w/ Door control Battery:

As the door control battery is installed between the vehicle battery and body ECU, first perform the inspections to confirm that there are no malfunctions in the power source circuit for the body ECU before performing this troubleshooting procedure.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PRECAUTION

·

w/ Automatic Light Control System:

If the body ECU has been replaced, it is necessary to initialize the body ECU.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)
a.

Disconnect the ignition or starter switch assembly connector.


b.
B343151E01
1.5,0.417 1.885,0.667 0.385,0.25 0.948,1.875 1.271,1.542 true 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 1.521,0.458 1.875,0.677 0.354,0.219 10 false G133 0.615,1.823 0.927,2.021 0.313,0.198 10 false AM1

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G133-5 (AM1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BODY ECU - IGNITION OR STARTER SWITCH ASSEMBLY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (BODY ECU - IGNITION OR STARTER SWITCH ASSEMBLY AND BODY GROUND)

b.

Connect the 2D, 2E and 2J instrument panel junction block assembly connectors.


c.

Disconnect the G133 ignition or starter switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G133-8 (IG1) - A-7 (IG) Always Below 1 Ω
G133-8 (IG1) - Body ground Always 10 kΩ or higher
A-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IGNITION OR STARTER SWITCH ASSEMBLY AND BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IGNITION OR STARTER SWITCH ASSEMBLY AND BODY GROUND)
a.

Disconnect the 2D, 2E and 2J instrument panel junction block assembly connectors.


b.

Disconnect the G133 ignition or starter switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G133-8 (IG1) - 2E-1 Always Below 1 Ω
2D-7 - 2D-5 Always Below 1 Ω
G133-8 (IG1) - Body ground Always 10 kΩ or higher
2D-7 - Body ground Always 10 kΩ or higher
2J-5 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR