Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › from 2016.07
RM33K0E _58 Vehicle Interior _043548 THEFT DETERRENT / KEYLESS ENTRY _0224643 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  


DESCRIPTION

When the communication line (EFIO-IMI) between the transponder key ECU assembly and ECM is stuck on HI output, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation The communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck on HI output (1 trip detection logic*).
·

Harness or connector

·

ECM

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait 6 seconds.



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A -

WIRING DIAGRAM

B418872E03
4.917,1.885 7.156,2.198 2.24,0.313 10 false G136 4.917,2.073 7.156,2.385 2.24,0.313 10 false Transponder Key ECU Assembly 1.302,1.917 3.542,2.229 2.24,0.313 10 false ECM 1.292,0.51 3.531,0.823 2.24,0.313 10 false +B 1.979,0.833 4.219,1.146 2.24,0.313 10 false IMI 2.365,0.948 4.604,1.26 2.24,0.313 10 false G56 2.719,0.948 4.958,1.26 2.24,0.313 10 false G129 3.146,0.948 5.385,1.26 2.24,0.313 10 false G50 2.396,0.719 4.635,1.031 2.24,0.313 10 false 10 2.813,0.719 5.052,1.052 2.24,0.333 10 false 30 3.198,0.719 5.438,1.052 2.24,0.333 10 false 16 2.427,1.188 4.667,1.5 2.24,0.313 10 false *1 2.823,1.188 5.063,1.5 2.24,0.313 10 false *2 3.229,1.188 5.469,1.5 2.24,0.313 10 false *3 2.698,1.688 4.938,2 2.24,0.313 10 false *1: for 2TR-FE, 2TR-FBE 2.708,1.938 4.948,2.25 2.24,0.313 10 false *2: for 1KD-FTV 2.719,2.198 4.958,2.51 2.24,0.313 10 false *3: for 1GD-FTV 4.76,0.854 7,1.188 2.24,0.333 10 false 13 5.021,0.865 7.156,1.188 2.135,0.323 10 false EFIO

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CLEAR DTC

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B279A is not output.



Result:
Result Proceed to
B279A is not output A
B279A is output B



A

B

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM AND BODY GROUND)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the G136 transponder key ECU assembly connector.


b.

Disconnect the G56*1, G129*2 or G50*3 ECM connector.

*1: for 2TR-FE, 2TR-FBE

*2: for 1KD-FTV

*3: for 1GD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 2TR-FE, 2TR-FBE
Tester Connection Condition Specified Condition
G136-13 (EFIO) - G56-10 (IMI) Always Below 1 Ω
G56-10 (IMI) - Body ground Always 10 kΩ or higher
G136-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1KD-FTV
Tester Connection Condition Specified Condition
G136-13 (EFIO) - G129-30 (IMI) Always Below 1 Ω
G129-30 (IMI) - Body ground Always 10 kΩ or higher
G136-13 (EFIO) - Body ground Always 10 kΩ or higher

for 1GD-FTV
Tester Connection Condition Specified Condition
G136-13 (EFIO) - G50-16 (IMI) Always Below 1 Ω
G50-16 (IMI) - Body ground Always 10 kΩ or higher
G136-13 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.REGISTER KEY
6.REGISTER KEY
a.

Register the key.

HINT:

refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

7.REGISTER ECU COMMUNICATION ID
7.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts with the key.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG (for 2TR-FE)
NG (for 2TR-FBE)
NG (for 1KD-FTV)
NG (for 1GD-FTV)



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG (for 2TR-FE)

NG (for 2TR-FBE)

NG (for 1KD-FTV)

NG (for 1GD-FTV)