Home › Engine / Hybrid System › 2TR-FBE INTAKE / EXHAUST › EXHAUST MANIFOLD › from 2016.07
RM33K0E _51 Engine / Hybrid System _054516 2TR-FBE INTAKE / EXHAUST _0267064 EXHAUST MANIFOLD A

2TR-FBE INTAKE / EXHAUST  EXHAUST MANIFOLD  INSTALLATION  


PROCEDURE

Hide 17141 1.INSTALL EXHAUST MANIFOLD

a.
A384259

Install a new gasket.


b.
A346102N01
1.448,0.021 1.604,0.219 0.156,0.198 10 true 1 2.24,1.25 2.396,1.448 0.156,0.198 10 true 2 2.885,0.375 3.042,0.573 0.156,0.198 10 true 3 1.302,1.229 1.458,1.427 0.156,0.198 10 true 5 3.083,1.323 3.24,1.521 0.156,0.198 10 true 4 0.115,0.854 0.271,1.052 0.156,0.198 10 true 6 2.906,0.073 3.063,0.271 0.156,0.198 10 true 8 0.49,0.021 0.646,0.219 0.156,0.198 10 true 7

Install the exhaust manifold with 8 new nuts, and tighten the nuts in the order shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 17118 2.INSTALL MANIFOLD STAY

a.
A345967N01
0.698,1.708 0.854,1.906 0.156,0.198 10 true A 0.708,0.708 0.865,0.906 0.156,0.198 10 true B 2.521,1.063 2.677,1.26 0.156,0.198 10 true C

Install the manifold stay with the 3 bolts.

Torque:
for bolt A : 71.5 N*m (729 kgf*cm, 53 ft.*lbf)
for bolt B : 44 N*m (449 kgf*cm, 32 ft.*lbf)
for bolt C : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 17410 3.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

40 mm (1.57 in.)


If the free length is less than the minimum, replace the compression spring.


b.
A076194C38
2.031,1.583 1.594,1.885 1.594,1.885 1.479,1.885 true 2.438,0.979 3.042,0.979 true 1.271,1.781 1.49,1.958 0.219,0.177 10 false *1 3.104,0.875 3.323,1.052 0.219,0.177 10 false *a
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap on a new gasket until its surface is flush with the exhaust manifold.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the front exhaust pipe assembly, do not push in the gasket with the front exhaust pipe assembly.




c.

Install the front exhaust pipe assembly to the No. 1 exhaust pipe support.


d.

Connect the front exhaust pipe assembly to the exhaust manifold with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


e.

Install a new gasket and connect the front exhaust pipe assembly to the tail exhaust pipe assembly with the 2 bolts and 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


f.

Connect the heated oxygen sensor connector and attach the 4 wire harness clamps.


g.

Connect the air fuel ratio sensor connector and attach the 3 wire harness clamps.


Hide 25710 4.INSTALL AIR SWITCHING VALVE ASSEMBLY