1.INSTALL ENGINE HANGER
12361
2.INSTALL FRONT ENGINE MOUNTING INSULATOR
Perform this procedure only when replacement of the front engine mounting insulator is necessary.
Install the 2 front engine mounting insulators to the 2 front engine mounting brackets with the 2 nuts.
12391
3.INSTALL FRONT ENGINE MOUNTING HEAT INSULATOR RH
Install the front engine mounting heat insulator RH to the front engine mounting insulator with the bolt.
82121
4.INSTALL ENGINE WIRE
Install the engine wire to the engine assembly.
11000
5.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Attach the engine sling device and hang the engine assembly with the chain block.
Remove the engine assembly from the engine stand.
11000
6.INSTALL ENGINE ASSEMBLY
Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
Slowly lower the engine assembly into the engine compartment.
Install the engine assembly to the body with the 4 bolts and 4 nuts.
Make sure to tighten the side with the nut.
When installing a bolt with a claw (stopper), make sure that the claw (stopper) does not damage the body of the vehicle.
Remove the 2 bolts and 2 engine hangers.
11355
7.INSTALL REAR END PLATE
Install the rear end plate to the cylinder block with the bolt.
Connect the No. 1 water by-pass pipe to the rear end plate with the bolt.
32101
8.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)
13405
9.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
31250
10.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)
31210
11.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)
31210
12.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transmission)
35000
13.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
14.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)
37100
15.INSTALL PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
51569
16.INSTALL PROPELLER SHAFT GUARD
17410
17.INSTALL FRONT EXHAUST PIPE ASSEMBLY
18.CONNECT ENGINE WIRE
Connect the sensor bracket to the right side of the frame with the bolt.
Connect the air fuel ratio sensor connector.
Connect the wire clamp to the front engine mounting bracket LH with the bolt.
Attach the clamp.
Connect the 2 connectors to the engine room relay block.
Connect the engine wire to the engine room relay block with the nut.
Attach the 2 claws and install the No. 1 relay block cover side to the engine room relay block.
Attach the 3 claws and install the No. 1 relay block cover upper to the engine room relay block.
Attach the clamp and install the No. 2 engine wire with the bolt.
Position the No. 2 engine wire as shown in the illustration.
Attach the 2 clamps and connect the No. 2 engine wire with the 2 bolts.
Install the battery tray.
Install the battery.
Install the battery hold down clamp with the 2 nuts.
Tighten the nut and install the positive (+) battery terminal.
Position the positive (+) battery terminal as shown in the illustration.
Connect the engine room main wire to the positive (+) battery terminal with the nut.
Connect the connector to the engine room main wire.
Push the engine wire through the dash panel into the cabin.
The wire should be within the range shown in the illustration.
Connect the engine wire to the air injection control bracket with the bolt.
Attach the clamp.
Connect the air injection control driver connector.
Connect the 3 glow plug controller connectors.
Attach the 2 clamps and connect the 3 connectors to the instrument panel wire.
89661
19.INSTALL ECM
55550
20.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
23271H
21.CONNECT NO. 1 FUEL HOSE
23273C
22.CONNECT NO. 2 FUEL HOSE
17344
23.CONNECT NO. 4 AIR INJECTION SYSTEM HOSE
44774
24.CONNECT UNION TO CONNECTOR TUBE HOSE
Connect the union to connector tube hose to the intake manifold, and slide the clamp to secure the hose.
25.CONNECT PURGE LINE HOSE
Connect the purge line hose to the purge VSV, and slide the clamp to secure the hose.
28100
26.INSTALL STARTER ASSEMBLY
88320
27.CONNECT COOLER COMPRESSOR ASSEMBLY
11452
28.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Install a new O-ring and the engine oil level dipstick guide with the bolt.
15301
29.INSTALL ENGINE OIL LEVEL DIPSTICK
44320
30.CONNECT VANE PUMP ASSEMBLY
Connect the vane pump assembly with the 2 bolts.
Connect the power steering oil pressure switch connector.
31.CONNECT HEATER HOSE
Connect the heater water outlet hose to the heater radiator unit sub-assembly, and slide the clamp to secure the hose.
Connect the heater water inlet hose to the heater radiator unit sub-assembly, and slide the clamp to secure the hose.
16400
32.INSTALL RADIATOR ASSEMBLY
32941
33.CONNECT NO. 1 OIL COOLER INLET HOSE (for Automatic Transmission)
32942
34.CONNECT NO. 1 OIL COOLER OUTLET HOSE (for Automatic Transmission)
16711
35.INSTALL FAN SHROUD
16470
36.INSTALL RADIATOR RESERVOIR
17621A
37.CONNECT AIR PUMP INLET
16572
38.INSTALL RADIATOR HOSE OUTLET
16571
39.INSTALL RADIATOR HOSE INLET
16593
40.INSTALL NO. 1 RADIATOR AIR GUIDE
53294C
41.INSTALL RADIATOR SIDE DEFLECTOR LH
53293C
42.INSTALL RADIATOR SIDE DEFLECTOR RH
Use the same procedure described for the LH side.
17861
43.INSTALL INTAKE AIR CONNECTOR
17701
44.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Install the air cleaner case sub-assembly with the 3 bolts.
Attach the 3 wire harness clamps.
17801
45.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Install the air cleaner filter element sub-assembly to the air cleaner cap sub-assembly.
17705
46.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE
Install the air cleaner cap sub-assembly with air cleaner hose and tighten the hose clamp.
Attach the 4 clamps.
Connect the intake mass air flow meter connector and attach the 2 wire harness clamps.
53301
47.INSTALL HOOD SUB-ASSEMBLY
Install the hood sub-assembly to the 2 hood hinge assemblies with the 4 bolts.
Connect the washer nozzle hose to the hood sub-assembly.
Adjust the hood sub-assembly.
48.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
49.ADD ENGINE OIL
50.ADD ENGINE COOLANT
33820B
51.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)
52.INSPECT SHIFT LEVER POSITION (for Automatic Transmission)
53.ADD AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
54.ADJUST AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)
55.ADD MANUAL TRANSMISSION OIL (for Manual Transmission)
56.INSPECT FOR FUEL LEAK
57.INSPECT FOR OIL LEAK
58.INSPECT FOR COOLANT LEAK
59.INSPECT FOR EXHAUST GAS LEAK
60.INSPECT IGNITION TIMING
61.INSPECT ENGINE IDLE SPEED
62.CHECK CO/HC
22030
63.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY
53882F
64.INSTALL FRONT FENDER SEAL LH
Install the front fender seal LH with 6 new clips.
53882F
65.INSTALL FRONT FENDER SEAL RH
Install the front fender seal RH with 6 new clips.
53737B
66.INSTALL FRONT UPPER FENDER APRON SEAL LH
Install the front upper fender apron seal LH with 6 new clips.
53736
67.INSTALL FRONT UPPER FENDER APRON SEAL RH
Install the front upper fender apron seal RH with 5 new clips.
51442
68.INSTALL NO. 2 ENGINE UNDER COVER
51410
69.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY