Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR(for 2TR-FBE) › from 2016.07
RM33K0E _58 Vehicle Interior _043555 HEATING / AIR CONDITIONING _0267652 COMPRESSOR(for 2TR-FBE) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 2TR-FBE)  INSTALLATION  


PROCEDURE

Hide 1.INSPECT COMPRESSOR OIL

a.
E321437

When replacing the compressor assembly with magnet clutch with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor assembly with magnet clutch before installation.

Standard:

(Oil capacity inside the new compressor assembly with magnet clutch: 150 to 165 cc (5.07 to 5.58 fl.oz)) - (Remaining oil amount in the removed compressor assembly with magnet clutch) = (Oil amount to be removed from the new compressor)


NOTICE:
·

If a new compressor assembly with magnet clutch is installed without removing some oil, there will be too much oil in the system due to the oil remaining in the pipes of the vehicle. Excessive oil in the system prevents heat exchange in the refrigeration cycle and causes ineffective cooling.

·

If the amount of oil remaining in the old compressor assembly with magnet clutch is too small, check the air conditioning system for oil leaks.

·

Be sure to use ND-OIL 8 or equivalent compressor oil. If any compressor oil other than ND-OIL 8 is used, compressor assembly with magnet clutch insulation performance may decrease, resulting in a leak of electric power.




Hide 2.INSTALL COMPRESSOR ASSEMBLY WITH MAGNET CLUTCH

a.
E321426

Using an E8 "TORX" socket wrench, temporarily install the compressor assembly with magnet clutch with the stud bolt.


b.

Tighten the stud bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.
E321425C02
1.833,1.938 2.063,2.135 0.229,0.198 10 true (2) 0.865,1.844 1.094,2.042 0.229,0.198 10 true (4) 1.479,0.563 1.708,0.76 0.229,0.198 10 true (3) 2.729,0.604 2.958,0.802 0.229,0.198 10 true (1)
V100135

Bolt
V100136

Nut


Tighten the 2 nuts and 2 bolts in the order shown in the illustration to install the compressor assembly with magnet clutch.

Torque:
Bolt, Nut : 24.5 N*m (250 kgf*cm, 18 ft.*lbf)


d.
E321424

Attach the clamp.


e.

Connect the connector.


Hide 88704 3.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.
E321423

Remove the vinyl tape from the suction hose sub-assembly and compressor assembly with magnet clutch.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.

Connect the suction hose sub-assembly to the compressor assembly with magnet clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.
E321422

Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose and compressor assembly with magnet clutch.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 1 cooler refrigerant discharge hose.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.

NOTICE:

Keep the O-ring and O-ring fitting surfaces free of foreign matter.



d.

Connect the No. 1 cooler refrigerant discharge hose to the compressor assembly with magnet clutch with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 53737B 5.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with 6 new clips.


Hide 6.INSTALL FRONT WHEEL LH

Hide 16572 7.INSTALL RADIATOR HOSE OUTLET

Hide 16361A 9.INSTALL FAN AND GENERATOR V BELT

Hide 12. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 51410 15.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY