The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the body ECU removal/installation are shown below.
| Replacement Part or Procedure | Necessary Procedures | Effects/Inoperative when not Performed | Link |
|---|---|---|---|
| Replacement of body ECU | Initialize automatic light control system | Automatic light control system | ( )
|
1.INSPECT INJ RELAY (INJ)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the INJ relay.
2.INSPECT A/F HTR RELAY (A/F HTR)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
If the result is not as specified, replace the A/F HTR relay.
82730
3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
Remove the body ECU from the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
Inspect the EFI-MAIN NO. 1 relay.
Before performing the relay inspections for the relays of instrument panel junction block assembly, inspect the EFI-MAIN NO. 1 and EFI NO. 1 fuses.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2B-1 - 2G-5 | Battery voltage not applied to terminals 2P-9 and 2J-5 | 10 kΩ or higher |
| Battery voltage applied to terminals 2P-9 and 2J-5 | Below 1 Ω | |
| 2B-1 - 2K-3 | Battery voltage not applied to terminals 2P-9 and 2J-5 | 10 kΩ or higher |
| Battery voltage applied to terminals 2P-9 and 2J-5 | Below 1 Ω | |
| 2B-1 - 2K-4 | Battery voltage not applied to terminals 2P-9 and 2J-5 | 10 kΩ or higher |
| Battery voltage applied to terminals 2P-9 and 2J-5 | Below 1 Ω | |
| 2B-1 - 2N-1 | Battery voltage not applied to terminals 2P-9 and 2J-5 | 10 kΩ or higher |
| Battery voltage applied to terminals 2P-9 and 2J-5 | Below 1 Ω |
If the result is not as specified, replace the instrument panel junction block assembly.
Inspect the C/OPN NO. 1 relay.
Before performing the relay inspections for the relays of instrument panel junction block assembly, inspect the EFI-MAIN NO. 1 and IG2 NO. 1 fuses and EFI-MAIN NO. 1 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2B-1 - 2K-5 | Battery voltage applied to terminals 2P-9 and 2J-5 and battery voltage not applied to terminals 2G-1 and 2P-8 | 10 kΩ or higher |
| Battery voltage applied to terminals 2P-9 and 2J-5, and 2G-1 and 2P-8 | Below 1 Ω |
If the result is not as specified, replace the instrument panel junction block assembly.
Install the body ECU to the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>INSTALLATION
Install the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>INSTALLATION