Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2016.07
RM33K0E _51 Engine / Hybrid System _054512 2TR-FBE ENGINE CONTROL _0269966 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P16A0  Delivery Heater Control Module Circuit/Open  P16A2  Delivery Heater Control Module System Voltage  


DESCRIPTION

The glow system consists of the glow plug controller, glow plugs and ECM. The ECM has heater operation permission judgment and target duty calculation functions. The heater operation permission judgment function uses the engine coolant temperature and ethanol concentration to determine whether a heater operation is necessary. The target duty calculation function calculates the heater duty ratio according to the engine coolant temperature and fuel flow amount during startup and sends the result to the glow plug controller.

The glow plug controller contains a self-diagnosis function. When the glow plug controller detects an internal malfunction, it sends a signal indicating the malfunction to the ECM. When the ECM receives this signal, it stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P16A0 Delivery Heater Control Module Circuit/Open When the glow plugs are on, the ECM detects that there is no output from the glow plug control unit for 3 seconds even though the ECM outputs an SI signal ("ON" command signal) (1 trip detection logic).
·

Open or short circuit in ground wire

·

Open or short circuit in battery wire

·

Open in SI wire

·

SI wire short circuit to ground or battery

·

Open in DI wire

·

DI wire short circuit to ground or battery

·

Low battery voltage

·

Glow plug controller

·

ECM


Does not come on DTC stored
P16A2 Delivery Heater Control Module System Voltage The glow plug controller recognizes the battery voltage as being 18.4 V or higher 3 times or more when the glow plugs are on (1 trip detection logic). Glow plug controller Does not come on DTC stored

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Clear the DTCs.

3.

Turn the ignition switch off for 30 seconds or more.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Using the GTS, switch the ECM from normal mode to check mode.

7.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P16A0 or P16A2.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A385053E02
1.385,0.51 1.698,0.708 0.313,0.198 10 false SI 1.385,0.927 1.698,1.125 0.313,0.198 10 false DI 1.26,1.354 1.719,1.552 0.458,0.198 10 false GL1 1.25,1.99 1.708,2.188 0.458,0.198 10 false GL2 1.24,2.615 1.698,2.813 0.458,0.198 10 false GL3 1.26,3.302 1.719,3.5 0.458,0.198 10 false GL4 1.323,3.885 1.635,4.083 0.313,0.198 10 false +B 1.188,4.354 1.802,4.552 0.615,0.198 10 false BATT 1.219,4.813 1.677,5.01 0.458,0.198 10 false GND 1.604,0.531 2.063,0.729 0.458,0.198 10 false C46 1.604,0.927 2.063,1.125 0.458,0.198 10 false C46 1.594,1.354 2.052,1.552 0.458,0.198 10 false C45 1.604,1.99 2.063,2.188 0.458,0.198 10 false C45 1.604,2.615 2.063,2.813 0.458,0.198 10 false C44 1.604,3.292 2.063,3.49 0.458,0.198 10 false C44 1.604,3.906 2.063,4.104 0.458,0.198 10 false C46 1.594,4.365 2.052,4.563 0.458,0.198 10 false A44 1.594,4.823 2.052,5.021 0.458,0.198 10 false C46 3.125,1.885 3.281,2.083 0.156,0.198 10 false 1 3.125,1.26 3.281,1.458 0.156,0.198 10 false 1 3.125,2.521 3.281,2.719 0.156,0.198 10 false 1 3.125,3.188 3.281,3.385 0.156,0.198 10 false 1 2.396,1.573 6.063,1.771 3.667,0.198 10 false No. 1 Glow Plug Assembly 2.396,2.208 6.063,2.406 3.667,0.198 10 false No. 2 Glow Plug Assembly 2.396,2.844 6.063,3.042 3.667,0.198 10 false No. 3 Glow Plug Assembly 2.385,3.5 6.052,3.698 3.667,0.198 10 false No. 4 Glow Plug Assembly 2.167,1.573 2.479,1.771 0.313,0.198 10 false g1 2.146,2.208 2.458,2.406 0.313,0.198 10 false g2 2.135,2.844 2.448,3.042 0.313,0.198 10 false g3 2.146,3.51 2.458,3.708 0.313,0.198 10 false g4 3.271,1.979 3.885,2.177 0.615,0.198 10 false GLW2 3.26,2.615 3.875,2.813 0.615,0.198 10 false GLW3 3.281,3.281 3.896,3.479 0.615,0.198 10 false GLW4 3.292,1.344 3.906,1.542 0.615,0.198 10 false GLW1 5.792,0.938 6.25,1.135 0.458,0.198 10 false G56 5.802,0.521 6.26,0.719 0.458,0.198 10 false C15 5.854,0.333 6.167,0.531 0.313,0.198 10 false 19 5.844,0.75 6.156,0.948 0.313,0.198 10 false 19 6.167,0.521 6.781,0.719 0.615,0.198 10 false GLDO 6.156,0.938 6.771,1.135 0.615,0.198 10 false GLDI 6.146,4.719 6.76,4.917 0.615,0.198 10 false GREL 3.188,5.042 3.802,5.24 0.615,0.198 10 false GLOW 2.99,4.615 3.146,4.813 0.156,0.198 10 false 1 3.74,4.635 3.896,4.833 0.156,0.198 10 false 2 2.979,4.271 3.135,4.469 0.156,0.198 10 false 3 3.74,4.26 3.896,4.458 0.156,0.198 10 false 5 5.792,4.719 6.25,4.917 0.458,0.198 10 false G57 5.885,4.521 6.042,4.719 0.156,0.198 10 false 7 1.688,0.344 1.844,0.542 0.156,0.198 10 false 3 1.688,0.75 1.844,0.948 0.156,0.198 10 false 5 1.688,1.167 1.844,1.365 0.156,0.198 10 false 1 1.688,1.802 1.844,2 0.156,0.198 10 false 2 1.677,2.417 1.833,2.615 0.156,0.198 10 false 1 1.677,3.115 1.833,3.313 0.156,0.198 10 false 2 1.677,3.719 1.833,3.917 0.156,0.198 10 false 4 1.667,4.177 1.823,4.375 0.156,0.198 10 false 1 1.667,4.635 1.823,4.833 0.156,0.198 10 false 1 0.5,5.313 3.563,5.51 3.063,0.198 10 false Glow Plug Controller 1.188,6.021 1.802,6.219 0.615,0.198 10 false GLOW 0.896,6.771 1.667,6.969 0.771,0.198 10 false J/B-B 0.656,7.875 1.729,8.073 1.073,0.198 10 false Battery 2.698,7.792 5.406,8.01 2.708,0.219 10 false Instrument Panel Junction Block Assembly 2.177,6.604 2.49,6.802 0.313,0.198 10 false 2B 2.188,6.969 2.5,7.167 0.313,0.198 10 false 2J 2.229,6.396 2.385,6.594 0.156,0.198 10 false 1 2.229,6.802 2.385,7 0.156,0.198 10 false 5 2.698,6.74 4.844,6.938 2.146,0.198 10 false EFI-MAIN NO. 1 3.688,7.271 5.833,7.469 2.146,0.198 10 false EFI-MAIN NO. 1 4.458,6.75 5.833,6.948 1.375,0.198 10 false EFI NO. 1 5.177,6.604 5.49,6.802 0.313,0.198 10 false 2N 5.167,6.958 5.479,7.156 0.313,0.198 10 false 2P 5.219,6.417 5.375,6.615 0.156,0.198 10 false 1 5.208,6.802 5.365,7 0.156,0.198 10 false 9 5.802,6.969 6.26,7.167 0.458,0.198 10 false G56 5.885,6.781 6.042,6.979 0.156,0.198 10 false 6 6.156,6.979 6.771,7.177 0.615,0.198 10 false MREL 6.333,8.198 6.792,8.396 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
P16A0 is output A
P16A2 is output B




A

2.CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)

B

9.REPLACE GLOW PLUG CONTROLLER
2.CHECK GLOW PLUG CONTROLLER (POWER SOURCE CIRCUIT)
a.
A241954C28
0.542,1 1.01,1.271 0.469,0.271 1.917,1.677 1.76,1.188 true 0.125,0.146 0.438,0.344 0.313,0.198 10 false *a 0.646,1.052 1,1.271 0.354,0.219 10 false C46 1.885,1.667 2.198,1.865 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Glow Plug Controller)


Disconnect the glow plug controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C46-4 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - BODY GROUND)
a.

Disconnect the glow plug controller connector.


b.
A241954C29
0.542,1 1.01,1.271 0.469,0.271 1.302,1.646 1.49,1.188 true 0.125,0.146 0.438,0.344 0.313,0.198 10 false *a 0.625,1.052 0.979,1.271 0.354,0.219 10 false C46 1.146,1.667 1.635,1.875 0.49,0.208 10 false GND
*a Front view of wire harness connector
(to Glow Plug Controller)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C46-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - ECM)
a.

Disconnect the glow plug controller connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C46-3 (SI) - C15-19 (GLDO) Always Below 1 Ω
C46-5 (DI) - G56-19 (GLDI) Always Below 1 Ω
C46-3 (SI) or C15-19 (GLDO) - Body ground and other terminals Always 10 kΩ or higher
C46-5 (DI) or G56-19 (GLDI) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE GLOW PLUG CONTROLLER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller.

Click hereEngine / Hybrid System>2TR-FBE FUEL>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Check for DTCs in check mode.



Result:
Proceed to
OK
NG



OK

END

NG

7.CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the glow plug controller connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C46-4 (+B) - 2N-1 Always Below 1 Ω
C46-4 (+B) or 2N-1 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK CHARGING SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK CHARGING SYSTEM
a.

Check the charging system and perform repairs as necessary.

Click herePower Source / Network>2TR-FBE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPLACE GLOW PLUG CONTROLLER
a.

Replace the glow plug controller.

Click hereEngine / Hybrid System>2TR-FBE FUEL>GLOW PLUG CONTROLLER>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Using the GTS, switch the ECM from normal mode to check mode.

Powertrain > Engine and ECT > Utility
Tester Display
Check Mode
50005 234 1

g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Confirm that the DTC is not output again.

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Check for DTCs in check mode.



Result:
Proceed to
NEXT



NEXT

END