Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › from 2016.07
RM33K0E _51 Engine / Hybrid System _054512 2TR-FBE ENGINE CONTROL _0269966 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P2440  Secondary Air Injection System Switching Valve Stuck Open Bank1  


DESCRIPTION

Refer to DTC P2431.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P2431

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2440 Secondary Air Injection System Switching Valve Stuck Open Bank1 Air pressure sensor detects pulsation of exhaust gas despite ECM commanding air switching valve to close, while engine running (1 trip detection logic)
·

Air switching valve

·

Open or short in air switching valve circuit

·

Air pressure sensor

·

Air pressure sensor circuit

·

Air injection control driver

·

ECM


Comes on DTC stored

HINT:

Air switching valve normal operation:

When the air switching valve is open, exhaust gas pulsation occurs in the secondary air passage.

When the air switching valve is closed, exhaust gas pulsation does not occur in the secondary air passage.


MONITOR DESCRIPTION

Air switching valve of the secondary air injection system.

If either of the following conditions occurs, the ECM interprets it as a malfunction of the secondary air injection system, and illuminates the MIL and stores a DTC:

·

Exhaust gas pulsation is detected by the air pressure sensor despite the ECM commanding the air switching valve to close.

·

Exhaust gas pulsation is not detected by the air pressure sensor despite the ECM commanding the air switching valve to open.


MONITOR STRATEGY

Required Sensors/Components Air pressure sensor
Frequency of Operation Once per drive cycle

TYPICAL MALFUNCTION THRESHOLDS

P2440 Air valve is stuck open:
P2440 Air valve is stuck open -
One of the following conditions is met A or B
A: Conditions 1 (AIR OFF) (Case1) -
B: Cumulative pressure pulsation (Case2) 80 kPa (600.05 mmHg) or higher

HINT:

Refer to "Data List / Active Test" [Air Pump Pressure (Absolute) and Air Pump Pulsation Pressure].

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST


CONFIRMATION DRIVING PATTERN

HINT:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON and turn the GTS on.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON and turn the GTS on.

8.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

9.

Start the engine after the GTS initialization is finished.

10.

Perform the System Check operation by pressing Next.

11.

Perform the following to confirm the secondary air injection system pending DTCs: Press Exit button.

12.

Check for pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

After the "Air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

14.

Input the DTC: P2440.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

Refer to the following pages.

·

Secondary air injection system air pressure sensor circuit.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P2431

·

Secondary air injection system air switching valve circuit.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P0412


CAUTION / NOTICE / HINT

HINT:
·

By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, Pending Codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read DTCs.

Result:
Result Proceed to
DTC P2440 is output A
DTC P2440 and P0412 are output B
DTC P2440 and other DTCs (except P0412) are output C



If any DTCs other than P2440 are output, troubleshoot those DTCs first.


A

2.INSPECT AIR PUMP ASSEMBLY

B

GO TO AIR SWITCHING VALVE INSPECTION PROCEDURE

C

2.INSPECT AIR PUMP ASSEMBLY

Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (SECONDARY AIR INJECTION SYSTEM OPERATION)

NG

3.PERFORM ACTIVE TEST USING GTS (SECONDARY AIR INJECTION SYSTEM OPERATION)
a.
A349023

Perform a visual check.

i.

Start the engine and warm it up.


ii.

Turn the ignition switch off.


iii.

Disconnect the NO. 4 air injection system hose.


iv.

Connect the GTS to the DLC3.


v.

Turn the ignition switch to ON and turn the GTS on.


vi.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

Powertrain > Engine and ECT > Utility
Tester Display
Secondary Air Injection Check
50005 234 26
HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



vii.

Start the engine.


viii.

Perform the secondary air injection system intrusive operation while the engine is idling.


ix.

Place your hand near the air switching valve port and check that the exhaust gas pressure pulsates when the ASV is turned on.

CAUTION:

To avoid the danger of being burned by the exhaust gas, bring your hand close to the valve port slowly.



x.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: CLOSE.

Powertrain > Engine and ECT > Utility
Tester Display
Secondary Air Injection Check
50005 234 26

xi.

Check that the exhaust gas does not pulsate when the ASV is turned off.


xii.

Turn the ignition switch off.

NOTICE:
·

This secondary air injection Check only allows technicians to operate the AIR system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



OK:
Air Pump Operation ASV Operation Exhaust Gas Pulsation
ON OFF Not detected
ON ON Detected



xiii.

Reconnect the NO. 4 air injection system hose.



Result:
Proceed to
OK
NG


HINT:

REFERENCE:

If the air pump operation is confirmed as normal, the air-fuel ratio detected in front of three-way catalytic converter changes in response to the secondary air pumped into the exhaust port when the air pump operates.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P2445



OK

4.INSPECT VACUUM HOSES (AIR SWITCHING VALVE - AIR PRESSURE SENSOR)

NG

6.INSPECT NO. 4 INTAKE PIPE (BLOCKAGES AND LEAKAGES)
4.INSPECT VACUUM HOSES (AIR SWITCHING VALVE - AIR PRESSURE SENSOR)
OK:

No blockage and no deformation in vacuum hose.


Result:
Proceed to
OK
NG



OK

5.INSPECT AIR PRESSURE SENSOR

NG

REPAIR OR REPLACE VACUUM HOSE

5.INSPECT AIR PRESSURE SENSOR
a.
A349022

Connect a pressure gauge to the air pressure sensor as shown in the illustration.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute).


f.

Check that the pressure displayed on the GTS fluctuates when applying the pressure to the air pressure sensor with the pressure gauge.

OK:

Pressure fluctuates in response to pressure applied with pressure gauge.


HINT:

The GTS displays the air pump pressure (Air Pump Pressure (Absolute)) as absolute pressure.



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT NO. 4 INTAKE PIPE (BLOCKAGES AND LEAKAGES)
a.
A349024

Check that the No. 4 intake pipe is securely connected to both the exhaust manifold and the air switching valve.


b.

Inspect the No. 4 intake pipe for blockages and damage.


OK:

No blockages or damage on No. 4 intake pipe.


Result:
Proceed to
OK
NG



OK

7.INSPECT AIR SWITCHING VALVE ASSEMBLY

NG

REPLACE NO. 4 INTAKE PIPE

7.INSPECT AIR SWITCHING VALVE ASSEMBLY
a.

Inspect the air switching valve assembly.

Click hereEngine / Hybrid System>2TR-FBE EMISSION CONTROL>AIR SWITCHING VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

8.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)

NG

8.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)
a.
A115629C01
0.115,1.271 0.49,1.635 0.375,0.365 0.188,3.563 0.594,3.906 0.406,0.344 2.052,1.646 2.385,2.177 true 1.052,1.656 0.76,2.146 true 1.375,3.688 1.094,4.26 true 0.208,0.219 0.521,0.417 0.313,0.198 10 false *a 0.198,1.365 0.51,1.563 0.313,0.198 10 false C6 0.26,3.635 0.719,3.833 0.458,0.198 10 false A25 2.354,2.229 2.667,2.427 0.313,0.198 10 false +B 0.688,2.229 0.844,2.427 0.156,0.198 10 false E 0.969,4.292 1.583,4.49 0.615,0.198 10 false BATT
*a Front view of wire harness connector
(to Air Injection Control Driver)


Disconnect the air injection control driver connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A25-1 (BATT) - Body ground Always 11 to 14 V
C6-5 (+B) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C6-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE AIR INJECTION CONTROL DRIVER POWER SOURCE CIRCUIT

9.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
a.

Disconnect the ECM connector.


b.

Disconnect the air injection control driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G57-5 (AIRV) - C6-3 (SIV) Always Below 1 Ω
G57-5 (AIRV) or C6-3 (SIV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.PERFORM ACTIVE TEST USING GTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.PERFORM ACTIVE TEST USING GTS
a.

Disconnect the air injection control driver connector.


b.
A229922C19
0.302,2.458 0.76,2.75 0.458,0.292 1.365,2.604 1.177,3.052 true 1.521,2.615 1.479,3.073 true 1.667,2.625 1.875,3.083 true 1.844,2.615 2.271,3.083 true 0.875,0.781 1.188,0.979 0.313,0.198 10 false DI 0.792,1.135 1.25,1.333 0.458,0.198 10 false SIV 2.375,0.781 2.99,0.979 0.615,0.198 10 false AIDI 2.365,1.167 2.979,1.365 0.615,0.198 10 false AIRV 1.073,3.135 1.229,3.333 0.156,0.198 10 false E 1.427,3.156 1.74,3.354 0.313,0.198 10 false DI 1.792,3.156 2.25,3.354 0.458,0.198 10 false SIV 2.219,3.146 2.677,3.344 0.458,0.198 10 false SIP 0.427,2.521 0.74,2.719 0.313,0.198 10 false C6 0.656,0.26 0.969,0.458 0.313,0.198 10 false *1 2.542,0.135 2.854,0.333 0.313,0.198 10 false *2 0.438,2.063 0.75,2.26 0.313,0.198 10 false *a
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)


Connect terminals DI and SIV of the wire harness connector for the air injection control driver.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

Powertrain > Engine and ECT > Utility
Tester Display
Secondary Air Injection Check
50005 234 26
HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



g.

Start the engine.


h.

Perform the secondary air injection system intrusive operation while the engine is idling.


i.

Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is on and off.


j.

Turn the ignition switch off.

NOTICE:
·

Do not perform the System Check operation repeatedly as it may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




Standard Voltage:
Tester Connection Condition Specified Condition
C6-3 (SIV) - C6-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
AIR PUMP: OFF, ASV: CLOSE 11 to 14 V


k.
A229922C20
0.281,2.354 0.615,2.646 0.333,0.292 1.365,2.635 1.198,3.083 true 1.51,2.615 1.417,3.115 true 1.677,2.635 1.708,3.125 true 1.854,2.615 2.104,3.094 true 2.385,0.802 3,1 0.615,0.198 10 false AIDI 2.375,1.156 2.99,1.354 0.615,0.198 10 false AIRP 0.875,0.771 1.188,0.969 0.313,0.198 10 false DI 0.792,1.135 1.25,1.333 0.458,0.198 10 false SIP 1.104,3.167 1.26,3.365 0.156,0.198 10 false E 1.375,3.177 1.688,3.375 0.313,0.198 10 false DI 1.635,3.188 2.094,3.385 0.458,0.198 10 false SIV 2.01,3.188 2.469,3.385 0.458,0.198 10 false SIP 0.354,2.417 0.667,2.615 0.313,0.198 10 false C6 0.646,0.198 0.958,0.396 0.313,0.198 10 false *1 2.542,0.125 2.854,0.323 0.313,0.198 10 false *2 0.354,1.875 0.667,2.073 0.313,0.198 10 false *a
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)


Connect terminals DI and SIP of the wire harness connector for the air injection control driver.


l.

Connect the GTS to the DLC3.


m.

Turn the ignition switch to ON.


n.

Turn the GTS on.


o.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV: OPEN.

Powertrain > Engine and ECT > Utility
Tester Display
Secondary Air Injection Check
50005 234 26
HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



p.

Start the engine.


q.

Perform the secondary air injection system intrusive operation while the engine is idling.


r.

Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is on and off.


s.

Turn the ignition switch off.

NOTICE:
·

Do not perform the System Check operation repeatedly as it may cause the damage in the system. If necessary, leave an interval of several minutes between System Check operations.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




Standard Voltage:
Tester Connection Condition Specified Condition
C6-4 (SIP) - C6-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
AIR PUMP: OFF, ASV: CLOSE 11 to 14 V


Result:
Proceed to
OK
NG



OK

11.REPLACE AIR INJECTION CONTROL DRIVER

NG

11.REPLACE AIR INJECTION CONTROL DRIVER
a.

Replace the air injection control driver.

Click hereEngine / Hybrid System>2TR-FBE EMISSION CONTROL>AIR INJECTION DRIVER>REMOVAL

Result:
Proceed to
NEXT




NEXT

12.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440)
12.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Clear DTCs (if stored).


g.

Turn the ignition switch off and wait for at least 30 seconds.


h.

Turn the ignition switch to ON.


i.

Enter the following menus: Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

Powertrain > Engine and ECT > Utility
Tester Display
Secondary Air Injection Check
50005 234 26

j.

Start the engine after the GTS initialization is finished.


k.

Perform the System Check operation by pressing Next.


l.

After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.


m.

Check pending DTCs.


n.

Turn the ignition switch off.

OK:

No pending DTC output.


NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




Result:
Proceed to
OK
NG



OK

END

NG