Home › Drivetrain › AC60E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FBE) › from 2016.07
RM33K0E _52 Drivetrain _043591 AC60E AUTOMATIC TRANSMISSION / TRANSAXLE _0276855 AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FBE) C

AC60E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FBE)  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) One of the following conditions is met:
(A) Any 2 or more of the following signals are ON simultaneously (2 trip detection logic):
·

One of the following conditions is met

·

P input signal is ON

·

N input signal is ON

·

NSW input signal is ON


·

R input signal

·

D input signal


(B) Any of the following signals is ON for 2.0 seconds or more with the shift lever in S (2 trip detection logic):
·

P input signal

·

N input signal

·

NSW input signal

·

R input signal


(C) All signals are OFF simultaneously for NSW, P, R, N and D (2 trip detection logic).
·

Open or short in park/neutral position switch assembly circuit

·

Transmission control switch (transmission floor shift assembly)

·

Park/neutral position switch assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicate a problem with the park/neutral position switch assembly and the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.

For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends a signal to the ECM according to the shift lever position (P, R, N, D or S). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C325301E02
0.406,2.271 1.75,2.458 1.344,0.188 10 false from IG1 NO. 1 Fuse 0.552,0.917 1.74,1.146 1.188,0.229 10 false to ST NO. 1 Relay 0.354,4.76 1.698,4.948 1.344,0.188 10 false from IG1 NO. 4 Fuse 5.667,6.094 6.125,6.292 0.458,0.198 10 false ECM 2.594,5.458 4.375,5.698 1.781,0.24 10 false Transmission Control Switch 2.208,3.792 4.635,4 2.427,0.208 10 false Park/Neutral Position Switch Assembly 4.938,3.177 5.396,3.375 0.458,0.198 10 false G56 4.938,2.573 5.396,2.771 0.458,0.198 10 false C16 4.938,1.969 5.396,2.167 0.458,0.198 10 false G56 4.938,1.385 5.396,1.583 0.458,0.198 10 false C16 4.938,0.927 5.396,1.125 0.458,0.198 10 false C15 4.938,4.76 5.396,4.958 0.458,0.198 10 false C16 2.208,3.625 2.667,3.823 0.458,0.198 10 false C22 2.615,5.271 3.073,5.469 0.458,0.198 10 false I1 3.49,4.646 3.646,4.844 0.156,0.198 10 false S 2.521,4.625 2.698,4.833 0.177,0.208 10 false 4 3.729,4.646 3.896,4.854 0.167,0.208 10 false 5 4.99,4.583 5.229,4.75 0.24,0.167 10 false 30 5.281,4.667 5.438,4.865 0.156,0.198 10 false S 3.74,0.813 3.917,1.021 0.177,0.208 10 false 4 2.51,0.823 2.677,1.031 0.167,0.208 10 false 5 2.75,0.833 2.917,1.042 0.167,0.208 10 false L 3.51,0.813 3.677,1.021 0.167,0.208 10 false B 2.781,4.625 3.042,4.813 0.26,0.188 10 false IG 3.469,1.26 3.729,1.448 0.26,0.188 10 false PL 3.458,1.854 3.719,2.042 0.26,0.188 10 false RL 3.448,2.448 3.708,2.635 0.26,0.188 10 false NL 3.458,3.052 3.719,3.24 0.26,0.188 10 false DL 2.74,2.167 3,2.354 0.26,0.188 10 false RB 2.51,2.177 2.688,2.385 0.177,0.208 10 false 2 3.729,1.271 3.906,1.479 0.177,0.208 10 false 6 3.74,1.844 3.917,2.052 0.177,0.208 10 false 1 3.74,2.438 3.917,2.646 0.177,0.208 10 false 9 3.729,3.052 3.906,3.26 0.177,0.208 10 false 7 4.969,0.719 5.198,0.917 0.229,0.198 10 false 15 4.979,1.188 5.208,1.385 0.229,0.198 10 false 25 5.021,1.76 5.25,1.958 0.229,0.198 10 false 8 4.979,2.365 5.208,2.563 0.229,0.198 10 false 24 4.979,2.969 5.208,3.167 0.229,0.198 10 false 18 5.281,1.25 5.542,1.438 0.26,0.188 10 false P 5.292,1.854 5.552,2.042 0.26,0.188 10 false R 5.302,2.438 5.563,2.625 0.26,0.188 10 false N 5.302,3.052 5.563,3.24 0.26,0.188 10 false D 5.281,0.802 5.781,0.99 0.5,0.188 10 false NSW 5.969,0.625 6.469,0.813 0.5,0.188 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON.*1

2.

Wait with the shift lever in each position (P, R, N and D) for 60 seconds or more.*2

3.

Wait for 2 seconds or more with the shift lever in S.*3

4.

Turn the ignition switch off.

5.

Perform steps (*1) through (*3) again.



DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed.

Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal Park/neutral position switch status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Shift SW Status (P Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Sports Mode Selection SW Sport mode select switch status ON or OFF
·

ON: Shift lever in S, "+" or "-"

·

OFF: Shift lever not in S, "+" or "-"


-
Shift SW Status (D Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in D, S, "+" or "-"

·

OFF: Shift lever not in D, S, "+" or "-"


When the shift lever position displayed on the GTS differs from the actual position, adjustment of the park/neutral position switch or the shift cable may be incorrect.
Powertrain > Engine and ECT > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Sports Mode Selection SW
Shift SW Status (D Range)
50003 234 147,125,126,127,133,128


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
a.
C321062C06
0.396,0.969 0.813,1.229 0.417,0.26 1.927,1.667 1.802,1.115 true 0.479,1.01 0.938,1.208 0.458,0.198 10 false C22 1.875,1.74 2.333,1.938 0.458,0.198 10 false RB 0.156,0.094 0.615,0.292 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C22-2 (RB) - Body ground Ignition switch ON 11 to 14 V
C22-2 (RB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE)
a.
C321062C07
0.396,0.979 0.813,1.24 0.417,0.26 2.542,1.563 2.135,1.083 true 0.479,1.031 0.938,1.229 0.458,0.198 10 false C22 2.583,1.615 3.042,1.813 0.458,0.198 10 false B 0.156,0.094 0.615,0.292 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C22-4 (B) - Body ground Ignition switch ON 11 to 14 V
C22-4 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712C86
0.896,1.688 1.313,1.271 true 2.5,1.542 2.104,1.26 true 2.188,1.625 1.969,1.292 true 1.719,1.594 1.719,1.292 true 0.76,0.771 1.26,0.969 true 1.021,0.469 1.583,0.938 true 2.26,0.458 1.885,0.969 true 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.573,0.667 0.885,0.865 0.313,0.198 10 false B 0.76,0.354 1.073,0.552 0.313,0.198 10 false RB 2.313,0.354 2.625,0.552 0.313,0.198 10 false RL 2.563,1.469 2.875,1.667 0.313,0.198 10 false L 2.177,1.667 2.49,1.865 0.313,0.198 10 false PL 1.656,1.656 1.969,1.854 0.313,0.198 10 false DL 0.76,1.688 1.073,1.885 0.313,0.198 10 false NL
*a Component without harness connected
(Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 5 (L) Shift lever in P or N Below 1 Ω
2 (RB) - 6 (PL) Shift lever in P Below 1 Ω
2 (RB) - 1 (RL) Shift lever in R Below 1 Ω
2 (RB) - 9 (NL) Shift lever in N Below 1 Ω
2 (RB) - 7 (DL) Shift lever in D, S, "+" or "-" Below 1 Ω
4 (B) - 5 (L) Shift lever not in P or N 10 kΩ or higher
2 (RB) - 6 (PL) Shift lever not in P 10 kΩ or higher
2 (RB) - 1 (RL) Shift lever not in R 10 kΩ or higher
2 (RB) - 9 (NL) Shift lever not in N 10 kΩ or higher
2 (RB) - 7 (DL) Shift lever not in D, S, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)

NG

4.CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)
a.
C267936C23
0.229,0.979 0.583,1.24 0.354,0.26 2.646,1.875 2,1.406 true 2.719,1.802 3.031,2 0.313,0.198 10 false IG 0.354,1.031 0.667,1.229 0.313,0.198 10 false I1 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I1-4 (IG) - Body ground Ignition switch ON 11 to 14 V
I1-4 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.
C277025C33
0.802,1.802 1.219,1.385 true 1.615,1.781 1.479,1.396 true 1.573,1.833 1.885,2.031 0.313,0.198 10 false IG 0.74,1.823 1.052,2.021 0.313,0.198 10 false S 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Transmission Control Switch)


Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω
4 (IG) - 5 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)

NG

REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, TRANSMISSION CONTROL SWITCH - ECM)
a.
C325710C01
1.563,0.219 1.917,0.427 0.354,0.208 2.01,0.219 2.365,0.427 0.354,0.208 0.552,2.729 1.365,1.792 true 0.823,3.042 1.427,1.792 true 1.396,2.74 1.49,1.875 true 2.208,3.052 2.573,1.708 true 2.833,2.771 2.635,1.76 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 1.615,0.25 1.885,0.438 0.271,0.188 10 false C16 2.063,0.25 2.396,0.427 0.333,0.177 10 false G56 0.635,3.094 1.063,3.281 0.427,0.188 10 false 24 (N) 0.344,2.781 0.75,2.969 0.406,0.188 10 false 25 (P) 1.219,2.792 1.667,2.99 0.448,0.198 10 false 30 (S) 2.083,3.104 2.396,3.281 0.313,0.177 10 false 8 (R) 2.698,2.833 3.094,3 0.396,0.167 10 false 18 (D)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C16-25 (P) - Body ground
·

Ignition switch ON

·

Shift lever in P


11 to 14 V
G56-8 (R) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V*
C16-24 (N) - Body ground
·

Ignition switch ON

·

Shift lever in N


11 to 14 V
G56-18 (D) - Body ground
·

Ignition switch ON

·

Shift lever in D, S, "+" or "-"


11 to 14 V
C16-30 (S) - Body ground
·

Ignition switch ON

·

Shift lever in S, "+" or "-"


11 to 14 V
C16-25 (P) - Body ground
·

Ignition switch ON

·

Shift lever not in P


Below 1 V
G56-8 (R) - Body ground
·

Ignition switch ON

·

Shift lever not in R


Below 1 V
C16-24 (N) - Body ground
·

Ignition switch ON

·

Shift lever not in N


Below 1 V
G56-18 (D) - Body ground
·

Ignition switch ON

·

Shift lever not in D, S, "+" or "-"


Below 1 V
C16-30 (S) - Body ground
·

Ignition switch ON

·

Shift lever not in S, "+" or "-"


Below 1 V


HINT:

*: The voltage will drop slightly due to lighting up of the back up light.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the C22 park/neutral position switch assembly connector.


b.

Disconnect the C15 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C22-4 (B) - C15-15 (NSW) Always Below 1 Ω
C22-4 (B) - Body ground Always 10 kΩ or higher
C15-15 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR