Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM3250E _51 Engine / Hybrid System _037981 1GR-FE ENGINE CONTROL _0176666 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off after the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A280176E48
0.948,3.438 2.719,3.698 1.771,0.26 10 false : CAN Communication Line 5.615,2.146 6,2.396 0.385,0.25 10 false ECM 0.75,2.292 2.615,2.594 1.865,0.302 10 false Combination Meter Assembly 5.281,2.146 5.698,2.333 0.417,0.188 10 false G88 0.74,2.125 1.042,2.323 0.302,0.198 10 false G9 2.042,1.604 2.417,1.76 0.375,0.156 10 false CANL 4.771,1.604 5.146,1.76 0.375,0.156 10 false CANL 2.042,0.885 2.479,1.052 0.438,0.167 10 false CANH 4.76,0.906 5.198,1.083 0.438,0.177 10 false CANH 4.49,0.719 4.688,0.875 0.198,0.156 10 false 31 4.49,1.417 4.677,1.604 0.188,0.188 10 false 25 2.521,0.729 2.896,0.958 0.375,0.229 10 false 36 2.531,1.427 2.896,1.76 0.365,0.333 10 false 35

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result:
MIL Condition Proceed to
Illuminates → Turns off Ignition switch to ON → engine is started A
Other than above - B




A

B

2.CHECK COMMUNICATION BETWEEN GTS AND ECM
2.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check the communication between the GTS and ECM.

HINT:

It can be checked using the "Engine and ECT" item of the Data List.



Result:
Result Proceed to
Communication is possible A
Communication is not possible B



A

3.CHECK WHETHER DTC OUTPUT RECURS

B

3.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check if any DTCs have been detected. Note down any DTCs.

Result:
Result Proceed to
DTCs are not output A
DTCs are output B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.




A

4.PERFORM ACTIVE TEST USING GTS (CHECK ENGINE INDICATOR)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

4.PERFORM ACTIVE TEST USING GTS (CHECK ENGINE INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Check Engine Indicator.

Body Electrical > Combination Meter > Active Test
Tester Display
Check Engine Indicator
50004 122 150

e.

Check the status of the MIL while performing the Active Test.

Result:
Result Proceed to
Changes A
Does not change B




A

B

REPLACE COMBINATION METER ASSEMBLY