The ECM constantly generates 5 V power source voltage from the battery voltages supplied to the +B, +B2 (BATT) terminals to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit has a short circuit, the CPU in the ECM and sensors that are supplied power through the VC circuit are deactivated because power is not supplied from the VC circuit. When the system is in this condition, it will not start.
For the circuit diagram of the ECM power source circuit.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>ECM Power Source Circuit
Check the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
| *a | Rear view of wire harness connector (to ECM) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G87-23 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| G87-22 (+B2) - Body ground | Ignition switch ON | 11 to 14 V |
If the result is not as specified, since current is not flowing to the +B and +B2 terminals of the ECM, the system may not be started.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the throttle body with motor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
Perform "Inspection After Repair" after replacing the throttle body with motor assembly.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
A
B
Disconnect the accelerator pedal sensor assembly connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the VVT sensor (for intake camshaft of bank 1) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the VVT sensor (for intake camshaft of bank 2) connector.
Turn the ignition switch to ON.
Turn the GTS on.
Check the communication between the GTS and ECM.
It can be checked using the "Engine and ECT" item of the Data List.
| Result | Proceed to |
|---|---|
| Communication is not possible | A |
| Communication is possible | B |
A
B
Disconnect the throttle body with motor assembly connector.
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the VVT sensor (for intake camshaft of bank 1) connector.
Disconnect the VVT sensor (for intake camshaft of bank 2) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C13-2 (VCTA) - Body ground and other terminals | Always | 10 kΩ or higher |
| G88-6 (VCPA) - Body ground and other terminals | Always | 10 kΩ or higher |
| G88-3 (VCP2) - Body ground and other terminals | Always | 10 kΩ or higher |
| C15-12 (VCV1) - Body ground and other terminals | Always | 10 kΩ or higher |
| C15-6 (VCV2) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG