Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM3250E _51 Engine / Hybrid System _037981 1GR-FE ENGINE CONTROL _0176666 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0230  Fuel Pump Primary Circuit  


DESCRIPTION

The FUEL PMP/AIR PMP HTR relay switches the fuel pump speed according to the engine conditions. The fuel pump operates when the ECM receives the STA signal and NE signal. The FUEL PMP/AIR PMP HTR relay is turned on while the engine is idling or operating at low load. This causes current to flow through the fuel pump resistor to the fuel pump. The fuel pump then operates at low speed. The FUEL PMP/AIR PMP HTR relay is turned off while the engine is cranking or operating at high load. The fuel pump then operates at normal speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0230 Fuel Pump Primary Circuit Open or short in FUEL PMP/AIR PMP HTR relay circuit
(1 trip detection logic)
·

Open or short in FUEL PMP/AIR PMP HTR relay circuit

·

FUEL PMP/AIR PMP HTR relay

·

ECM


- DTC stored

MONITOR DESCRIPTION

This DTC is designed to detect a malfunction in the FUEL PMP/AIR PMP HTR relay circuit. When the system is normal, battery voltage is applied to the FPR terminal of the ECM while the FUEL PMP/AIR PMP HTR relay is off. If battery voltage is not applied to the FPR terminal while the FUEL PMP/AIR PMP HTR relay is off, the ECM interprets this as a malfunction. The ECM then illuminates the MIL and stores a DTC.

WIRING DIAGRAM

A353941E01
4.646,0.365 5.333,0.542 0.688,0.177 10 false NE Signal 4.573,0.792 5.333,1 0.76,0.208 10 false STA Signal 5.99,0.24 6.448,0.438 0.458,0.198 10 false NE+ 6,0.667 6.458,0.865 0.458,0.198 10 false STA 5.667,0.167 5.979,0.365 0.313,0.198 10 false 16 5.677,0.604 5.99,0.802 0.313,0.198 10 false 28 5.635,0.365 6.094,0.563 0.458,0.198 10 false C15 5.635,0.802 6.094,1 0.458,0.198 10 false G88 5.958,2.198 6.417,2.396 0.458,0.198 10 false MREL 5.625,2.219 6.083,2.417 0.458,0.198 10 false G88 5.667,2 5.979,2.198 0.313,0.198 10 false 36 4.813,2.625 5.479,2.99 0.667,0.365 10 false EFI-MAIN NO.1 3.823,1.708 4.458,2.052 0.635,0.344 10 false EFI-MAIN NO.1 3.563,4.073 4.417,4.24 0.854,0.167 10 false C/OPN NO.1 4.635,3.271 5.271,3.615 0.635,0.344 10 false IG2 NO.1 3.188,2.031 3.573,2.375 0.385,0.344 10 false AM2 NO.2 3.052,1.563 3.365,1.76 0.313,0.198 10 false 2B 3.094,1.365 3.25,1.563 0.156,0.198 10 false 1 0.729,1.708 1.5,1.906 0.771,0.198 10 false J/B-B 3.052,2.688 3.365,2.885 0.313,0.198 10 false 2G 3.094,2.49 3.25,2.688 0.156,0.198 10 false 6 5.198,2.219 5.51,2.417 0.313,0.198 10 false 2P 5.229,2 5.406,2.229 0.177,0.229 10 false 9 5.021,4.771 5.333,4.969 0.313,0.198 10 false 2P 5.302,4.75 5.479,4.979 0.177,0.229 10 false 8 4.51,4.771 4.823,4.969 0.313,0.198 10 false 2K 4.302,4.75 4.479,4.979 0.177,0.229 10 false 5 5.625,5.458 6.083,5.656 0.458,0.198 10 false G87 5.99,5.333 6.448,5.531 0.458,0.198 10 false FC 5.708,5.25 5.885,5.479 0.177,0.229 10 false 5 5.99,7.104 6.448,7.302 0.458,0.198 10 false FPR 5.625,7.24 6.083,7.438 0.458,0.198 10 false G87 5.708,7.01 5.885,7.24 0.177,0.229 10 false 4 6.354,8.01 6.813,8.208 0.458,0.198 10 false ECM 2.927,5.01 4.542,5.427 1.615,0.417 10 false Instrument Panel Junction Block Assembly 4.854,6.24 5.938,6.594 1.083,0.354 10 false FUEL PMP/AIR PMP HTR 3.052,3.417 3.365,3.615 0.313,0.198 10 false 2G 3.094,3.208 3.25,3.406 0.156,0.198 10 false 1 1.594,6.031 2.729,6.229 1.135,0.198 10 false Ignition Switch*1 2.229,5.469 2.688,5.667 0.458,0.198 10 false IG2 1.615,5.458 2.073,5.656 0.458,0.198 10 false AM2 0.354,5.74 1.49,6.094 1.135,0.354 10 false STRG LOCK/AM2 NO.1 0.354,6.865 1.385,7.052 1.031,0.188 10 false FL MAIN 3.0W 0.479,8.094 1.021,8.313 0.542,0.219 10 false Battery 1.844,7.99 3.219,8.188 1.375,0.198 10 false Fuel Pump 2.323,7.24 2.667,7.5 0.344,0.26 10 false A53 1.844,7.813 2.083,8.052 0.24,0.24 10 false O6 2.313,7.417 3.688,7.615 1.375,0.198 10 false Fuel Pump Resistor 1.583,5.875 1.885,6.063 0.302,0.188 10 false G1 1.146,4.542 2.656,4.917 1.51,0.375 10 false Certification ECU (Smart Key ECU Assembly)*2 1.146,4.375 1.5,4.594 0.354,0.219 10 false G69 0.823,4.302 1.135,4.5 0.313,0.198 10 false 20 0.604,4.531 0.99,4.76 0.385,0.229 10 false IG1D 1.406,3.781 1.563,3.979 0.156,0.198 10 false 1 1.406,3.281 1.563,3.479 0.156,0.198 10 false 5 2.208,3.302 2.365,3.5 0.156,0.198 10 false 3 2.208,3.792 2.365,3.99 0.156,0.198 10 false 2 3.688,7.896 5.604,8.313 1.917,0.417 10 false *1: w/o Entry and Start System *2: w/ Entry and Start System 1.729,4.177 2.188,4.375 0.458,0.198 10 false IG2*2 2.563,5.448 2.719,5.646 0.156,0.198 10 false 3 1.417,5.458 1.573,5.656 0.156,0.198 10 false 4 4.656,5.885 4.813,6.083 0.156,0.198 10 false 2 4.094,5.896 4.25,6.094 0.156,0.198 10 false 3 4.646,6.729 4.802,6.927 0.156,0.198 10 false 1 4.01,6.719 4.167,6.917 0.156,0.198 10 false 4 4.365,6.719 4.542,6.948 0.177,0.229 10 false 5 3.229,6.958 3.385,7.156 0.156,0.198 10 false 1 2.51,6.948 2.667,7.146 0.156,0.198 10 false 2 1.635,7.49 1.792,7.688 0.156,0.198 10 false 4 1.615,8.354 1.792,8.583 0.177,0.229 10 false 5 1.406,7.698 1.563,7.896 0.156,0.198 10 false B 1.406,8.167 1.563,8.365 0.156,0.198 10 false E

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT FUEL PUMP RELAY (FUEL PMP/AIR PMP HTR)
a.

Inspect the FUEL PMP/AIR PMP HTR relay.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (FUEL PMP/AIR PMP HTR RELAY)

NG

REPLACE RELAY (FUEL PMP/AIR PMP HTR)

2.CHECK TERMINAL VOLTAGE (FUEL PMP/AIR PMP HTR RELAY)
A348211C01
0.5,0.427 0.813,0.583 0.313,0.156 10 false *1 0.229,2.24 0.542,2.396 0.313,0.156 10 false *2
*1 Engine Room Relay Block Assembly
*2 FUEL PMP/AIR PMP HTR


a.

Remove the FUEL PMP/AIR PMP HTR relay from the Engine Room Relay Block Assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
FUEL PMP/AIR PMP HTR relay terminal 2 - Body ground Cranking 11 to 14 V
FUEL PMP/AIR PMP HTR relay terminal 2 - Body ground Ignition switch ON 0 to 3 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FUEL PMP/AIR PMP HTR RELAY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (FUEL PMP/AIR PMP HTR RELAY - ECM)
a.

Remove the FUEL PMP/AIR PMP HTR relay from the Engine Room Relay Block Assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FUEL PMP/AIR PMP HTR relay terminal 1 - G87-4 (FPR) Always Below 1 Ω
FUEL PMP/AIR PMP HTR relay terminal 1 or G87-4 (FPR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PMP/AIR PMP HTR RELAY - ECM)