Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM
RM3250E _51 Engine / Hybrid System _037981 1GR-FE ENGINE CONTROL _0176666 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, an STA signal is sent to the ECM from ignition switch*1 or certification ECU (smart key ECU assembly)*2. When the STA and NE signals are received by the ECM, Tr1 inside the ECM turns on and current flows through the coil of the C/OPN NO.1 relay. As a result, the relay switches on and the fuel pump operates with power from the FUEL PMP/AIR PMP HTR relay. While the NE signal is being sent (while the engine is running), the fuel pump continues to operate since Tr1 in the ECM continues to stay on (the C/OPN NO.1 relay is on). The speed of the fuel pump is regulated at two speeds (high and low) according to the state of the engine (cranking, light load or heavy load). When Tr2 inside the ECM is off, the fuel pump operates at high speed. When Tr2 turns on during idling or light loads, current flows to the fuel pump through the fuel pump resistor and the fuel pump operates at low speed.

*1: w/o Entry and Start System

*2: w/ Entry and Start System

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (OPERATE C/OPN NO.1 RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check the relay operation while operating it using the GTS.

Standard:

Operating noise can be heard from the relay.



Result:
Proceed to
OK
NG



OK

2.INSPECT RELAY (FUEL PMP/AIR PMP HTR)

NG

7.CHECK ECM POWER SOURCE CIRCUIT
2.INSPECT RELAY (FUEL PMP/AIR PMP HTR)
a.

Inspect the relay (FUEL PMP/AIR PMP HTR).

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT TERMINAL VOLTAGE (FUEL PMP/AIR PMP HTR RELAY TERMINAL)

NG

REPLACE RELAY (FUEL PMP/AIR PMP HTR)

3.INSPECT TERMINAL VOLTAGE (FUEL PMP/AIR PMP HTR RELAY TERMINAL)
A348211C01
0.5,0.427 0.813,0.583 0.313,0.156 10 false *1 0.229,2.24 0.542,2.396 0.313,0.156 10 false *2
*1 Engine Room Relay Block Assembly
*2 FUEL PMP/AIR PMP HTR


a.

Remove the FUEL PMP/AIR PMP HTR relay from the engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
FUEL PMP/AIR PMP HTR relay terminal 2 - Body ground Cranking 11 to 14 V
FUEL PMP/AIR PMP HTR relay terminal 3 - Body ground Cranking 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL PUMP RESISTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (C/OPN NO.1 RELAY - FUEL PMP/AIR PMP HTR RELAY, EFI-MAIN NO.1 RELAY)

4.INSPECT FUEL PUMP RESISTOR

Inspect fuel pump resistor.

Click hereEngine / Hybrid System>1GR-FE FUEL>FUEL PUMP RESISTOR>INSPECTION

Result:
Result Proceed to
OK A
NG B



A

5.INSPECT FUEL PUMP

B

5.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>1GR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PMP/AIR PMP HTR RELAY - FUEL PUMP RESISTOR, FUEL PUMP, ECM)

NG

6.CHECK HARNESS AND CONNECTOR (FUEL PMP/AIR PMP HTR RELAY - FUEL PUMP RESISTOR, FUEL PUMP, ECM)
a.

Remove the FUEL PMP/AIR PMP HTR relay from the engine room relay block assembly.


b.

Disconnect the fuel pump resistor connector.


c.

Disconnect the fuel pump connector.


d.

Disconnect the ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FUEL PMP/AIR PMP HTR relay terminal 5 - A53-1 Always Below 1 Ω
A53-2 - O6-4 Always Below 1 Ω
FUEL PMP/AIR PMP HTR relay terminal 4 - O6-4 Always Below 1 Ω
O6-5 - Body ground Always Below 1 Ω
FUEL PMP/AIR PMP HTR relay terminal 1 - G87-4 (FPR) Always Below 1 Ω
FUEL PMP/AIR PMP HTR relay terminal 5 or A53-1 - Body ground Always 10 kΩ or higher
A53-2 or O6-4 - Body ground Always 10 kΩ or higher
FUEL PMP/AIR PMP HTR relay terminal 4 or O6-4 - Body ground Always 10 kΩ or higher
FUEL PMP/AIR PMP HTR relay terminal 1 or G87-4 (FPR) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Click here


7.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
OK
NG



OK

8.INSPECT RELAY (C/OPN NO.1)

NG

REPAIR OR REPLACE ECM POWER SOURCE CIRCUIT

8.INSPECT RELAY (C/OPN NO.1)

Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (C/OPN NO.1 RELAY - ECM)

NG

REPLACE RELAY (C/OPN NO.1)

9.CHECK HARNESS AND CONNECTOR (C/OPN NO.1 RELAY - ECM)
a.

Disconnect the instrument panel junction block connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2P-8 - G87-5 (FC) Always Below 1 Ω
2P-8 or G87-5 (FC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR