Home › Drivetrain › AC60F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)
RM3250E _52 Drivetrain _038031 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0178581 AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)  P2759  Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU)  


DESCRIPTION

Refer to the system description for DTC P2757.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)>P2757

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2759 Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while driving (1 trip detection logic).
·

Open or short in shift solenoid valve SLU circuit

·

Shift solenoid valve SLU

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

When an open or short in a shift solenoid valve SLU circuit is detected, the ECM determines there is a malfunction. The ECM will illuminate the MIL and store this DTC.

WIRING DIAGRAM

C311453E46
1.49,1.729 5.156,1.927 3.667,0.198 10 false Shift Solenoid Valve SLU 5.167,1.135 5.781,1.333 0.615,0.198 10 false SLU+ 5.167,2.115 5.781,2.313 0.615,0.198 10 false SLU- 4.969,2.115 5.583,2.313 0.615,0.198 10 false 1 4.969,1.135 5.583,1.333 0.615,0.198 10 false 2 3.906,1.135 4.521,1.333 0.615,0.198 10 false 21 3.906,2.115 4.521,2.313 0.615,0.198 10 false 22 1.26,1.344 1.875,1.542 0.615,0.198 10 false 1 1.271,2.125 1.885,2.323 0.615,0.198 10 false 2 3.438,1.135 4.052,1.333 0.615,0.198 10 false SLU+ 3.448,2.115 4.063,2.313 0.615,0.198 10 false SLU- 5.75,0.781 6.365,0.979 0.615,0.198 10 false 12 V 1.813,2.719 2.271,2.917 0.458,0.198 10 false C42 1.823,2.885 4.427,3.083 2.604,0.198 10 false Transmission Wire 5.573,3.021 5.885,3.219 0.313,0.198 10 false C54 5.573,3.198 6.031,3.396 0.458,0.198 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 2TR-FE)>INITIALIZATION


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLU)
a.
C319326C08
2.104,1.75 2.281,1.375 true 2.635,1.781 2.438,1.375 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 1.958,1.792 2.427,1.99 0.469,0.198 10 false SLU- 2.531,1.823 3,2.083 0.469,0.26 10 false SLU+
*a Component without harness connected
(Transmission Wire)


Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
21 (SLU+) - 22 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
21 (SLU+) - Body ground Always 10 kΩ or higher
22 (SLU-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLU
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C325711C18
1.552,0.198 1.896,0.417 0.344,0.219 2.333,2.74 2,1.635 true 1.271,2.74 1.917,1.635 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 1.594,0.24 1.938,0.438 0.344,0.198 10 false C54 2.073,2.792 2.76,2.979 0.688,0.188 10 false 1 (SLU-) 0.927,2.781 1.677,2.979 0.75,0.198 10 false 2 (SLU+)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C54-2 (SLU+) - C54-1 (SLU-) 20°C (68°F) 5.0 to 5.6 Ω
C54-2 (SLU+) - Body ground Always 10 kΩ or higher
C54-1 (SLU-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLU
a.
C201747C15
1.49,0.875 0.635,0.646 false 1.781,0.865 2.479,0.625 false 1.49,3.125 0.635,2.896 false 1.781,3.125 2.479,2.885 false 2.542,0.552 2.719,0.75 0.177,0.198 10 false 1 0.51,0.563 0.688,0.76 0.177,0.198 10 false 2 1.177,4.198 1.385,4.406 0.208,0.208 10 false (-) 1.917,4.208 2.146,4.406 0.229,0.198 10 false (+) 2.563,2.792 2.74,2.99 0.177,0.198 10 false 1 0.49,2.813 0.667,3.01 0.177,0.198 10 false 2 0.135,0.135 0.354,0.344 0.219,0.208 10 false *1
*1 Shift Solenoid Valve SLU


Remove shift solenoid valve SLU.

Click hereDrivetrain>AC60F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG