Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM3250E _54 Brake _038044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0178882 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1417  High Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the +BS terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or generator circuit, etc.

The DTC is canceled when the +BS terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1417 High Power Supply Voltage Malfunction Either of the following is detected:
1.

The +BS terminal voltage is 17.4 V or more for 0.8 seconds or more.

2.

When voltage at terminal +BS is 17.4 V or higher, power supply voltage of master cylinder pressure sensor is cut for 0.2 seconds or more.


·

Charging system

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector

·

ABS NO. 2 fuse

·

Battery



WIRING DIAGRAM

C307645E04
3.708,2.885 4.885,3.135 1.177,0.25 10 false Skid Control ECU 5.313,1.49 6.406,2.021 1.094,0.531 10 false Master Cylinder Pressure Sensor 3.177,0.854 3.635,1.052 0.458,0.198 10 false +BS 2.802,0.865 3.26,1.063 0.458,0.198 10 false 38 1.781,1.167 2.531,1.5 0.75,0.333 10 false ABS NO. 2 0.417,0.969 1.396,1.333 0.979,0.365 10 false from Battery 3.156,2.146 3.615,2.344 0.458,0.198 10 false GND1 2.833,2.146 3.292,2.344 0.458,0.198 10 false 25 3.104,3.271 3.563,3.469 0.458,0.198 10 false A4 3.375,3.271 5.385,3.542 2.01,0.271 10 false Brake Actuator Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

2.CHECK TERMINAL VOLTAGE (+BS TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.
C306843C60
1.531,0.104 1.896,0.333 0.365,0.229 3.25,1.781 3.25,1.583 3.25,1.583 2.75,1.26 true 0.177,1.677 0.177,1.479 0.177,1.479 0.635,1.25 true 3.115,1.823 3.427,2.021 0.313,0.198 10 false +BS 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 1.625,0.135 2.083,0.333 0.458,0.198 10 false A4 0.052,1.698 0.49,1.896 0.438,0.198 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A4 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A4-38 (+BS) - Body ground Always 11 to 14 V
A4-38 (+BS) -A4-25 (GND1) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the A4 skid control ECU (brake actuator assembly) connector.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC C1417 is not output
DTC C1417 is output



DTC C1417 is not output

DTC C1417 is output