Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM3250E _54 Brake _038044 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0178882 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1268  Transfer L4 Position Switch Circuit  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area
C1268 Transfer L4 Position Switch Circuit Either of the following is detected:
1.

No signal is input to the EXI4 terminal of the skid control ECU.

2.

The skid control ECU receives an L4 abnormal status signal from the 4 wheel drive control ECU via CAN.


·

L4 detection switch (Transfer shift actuator assembly)

·

L4 detection switch circuit

·

Skid control ECU (Brake actuator assembly)

·

4 wheel drive control ECU

·

Touch select 2-4 and high-low system



WIRING DIAGRAM

C332382E01
4.135,3.844 4.594,4.042 0.458,0.198 10 false C41 4.135,4.042 6.323,4.521 2.188,0.479 10 false L4 Detection Switch (Transfer Shift Actuator Assembly) 4.375,3.104 4.635,3.302 0.26,0.198 10 false L4 4.083,3.083 4.344,3.281 0.26,0.198 10 false 9 5.604,3.135 6.063,3.333 0.458,0.198 10 false GND 6.042,3.094 6.302,3.292 0.26,0.198 10 false 10 0.979,2.344 1.438,2.542 0.458,0.198 10 false A4 0.969,2.531 2.594,2.938 1.625,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 2.25,1.938 2.708,2.135 0.458,0.198 10 false EXI4 2.708,1.792 2.969,1.99 0.26,0.198 10 false 5 4.698,2.521 6.792,2.938 2.094,0.417 10 false 4 Wheel Drive Control ECU 4.677,2.344 5.135,2.542 0.458,0.198 10 false C39 4.792,1.948 5.25,2.146 0.458,0.198 10 false 4WDL 4.5,1.802 4.729,2 0.229,0.198 10 false 3 0.938,1.24 1.604,1.635 0.667,0.396 10 false ECM 0.917,1.031 2.448,1.344 1.531,0.313 10 false C60*1, G87*2, G46*3 2.646,0.438 3.719,0.708 1.073,0.271 10 false 12*1, 8*2, 25*3 2.385,0.604 2.844,0.802 0.458,0.198 10 false L4 4.781,0.615 5.24,0.813 0.458,0.198 10 false L4 4.74,1.188 5.406,1.583 0.667,0.396 10 false TCM 4.75,1.01 5.271,1.198 0.521,0.188 10 false G89*4 0.115,3.385 2.156,3.646 2.042,0.26 10 false *1: for 1GD-FTV and 2GD-FTV 0.135,3.698 1.375,3.917 1.24,0.219 10 false *2: for 1GR-FE 0.135,4.031 1.375,4.25 1.24,0.219 10 false *3: for 2TR-FE 0.156,4.354 1.396,4.573 1.24,0.219 10 false *4: for 1KD-FTV 4.521,0.458 4.76,0.667 0.24,0.208 10 false 15

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


HINT:

When DTC U0114 is output together with DTC C1268, inspect and repair the trouble areas indicated by DTC U0114 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073


PROCEDURE

1.INSPECT TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
a.

Turn the 4WD control switch (transfer position switch) to L4, and then drive the vehicle and check that there are no problems with the touch select 2-4 and high-low system.

OK:

There are no problems with the touch select 2-4 and high-low system.


Result:
Result
OK
NG




OK

2.CHECK HARNESS AND CONNECTOR (EXI4 TERMINAL)

NG

2.CHECK HARNESS AND CONNECTOR (EXI4 TERMINAL)
a.

Connect the A4 skid control ECU (brake actuator assembly) connector.


b.

Turn the 4WD control switch (transfer position switch) to L4.


c.

Disconnect the C60*1, G87*2 or G46*3 ECM connector.

*1: for 1GD-FTV and 2GD-FTV

*2: for 1GR-FE

*3: for 2TR-FE



d.

Disconnect the G89* TCM connector.

*: for 1KD-FTV



e.

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


C306843C63
1.521,0.094 1.885,0.313 0.365,0.219 1.365,0.854 1.094,0.281 1.094,0.281 0.927,0.281 false 0.625,0.208 1.01,0.406 0.385,0.198 10 false EXI4 0.063,0.042 0.448,0.24 0.385,0.198 10 false *a 1.604,0.115 1.99,0.313 0.385,0.198 10 false A4
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A4-5 (EXI4) - Body ground
·

Ignition switch ON

·

4WD control switch (transfer position switch) set to L4


Below 1.5 V



g.

Reconnect the A4 skid control ECU (brake actuator assembly) connector.


h.

Reconnect the C60*1, G87*2 or G46*3 ECM connector.

*1: for 1GD-FTV and 2GD-FTV

*2: for 1GR-FE

*3: for 2TR-FE



i.

Reconnect the G89* TCM connector.

*: for 1KD-FTV



j.

Turn the 4WD control switch (transfer position switch) to H2 or H4.


k.

Disconnect the C60*1, G87*2 or G46*3 ECM connector.

*1: for 1GD-FTV and 2GD-FTV

*2: for 1GR-FE

*3: for 2TR-FE



l.

Disconnect the G89* TCM connector.

*: for 1KD-FTV



m.

Disconnect the A4 skid control ECU (brake actuator assembly) connector.


n.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A4-5 (EXI4) - Body ground
·

Ignition switch ON

·

4WD control switch (transfer position switch) set to H2 or H4


11 to 14 V



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EXI4 CIRCUIT)

3.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Reconnect the A4 skid control ECU (brake actuator assembly) connector.


c.

Reconnect the C60*1, G87*2 or G46*3 ECM connector.

*1: for 1GD-FTV and 2GD-FTV

*2: for 1GR-FE

*3: for 2TR-FE



d.

Reconnect the G89* TCM connector.

*: for 1KD-FTV



e.

Turn the ignition switch to ON.


f.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

g.

Turn the ignition switch off.


h.

Start the engine.


i.

Turn the 4WD control switch (transfer position switch) to H2 or H4.


j.

Turn the 4WD control switch (transfer position switch) to L4, drive the vehicle, and then check for DTCs.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is output
DTC is not output




DTC is output

DTC is not output