To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.
1.PERFORM SPARK TEST
To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.
Check for DTCs.
Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
If a DTC is output, perform troubleshooting procedures for that DTC.
Check if sparks occur.
Remove the 4 ignition coil assemblies and 4 spark plugs.
Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL
Disconnect the 4 injector connectors.
Install the spark plug to the ignition coil assembly and connect the ignition coil connector.
Ground the spark plug.
Visually check that sparks occur while the engine is being cranked.
When performing the inspection, be sure to ground the hexagonal portion or the threaded portion of the spark plug.
Do not crank the engine for more than 2 seconds.
If an ignition coil assembly is struck or dropped, replace it with a new one.
If a spark plug is struck or dropped, replace it with a new one.
2.PERFORM IGNITION COIL AND SPARK TEST
Perform "Inspection After Repair" after replacing a spark plug or ignition coil assembly.
Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
Spark test procedure.
Check that the wire harness side connector of the ignition coil assembly is securely connected.
| Result | Proceed to |
|---|---|
| NG | Connect securely |
| OK | Go to next step |
Perform a spark test on the malfunctioning ignition coil assembly.
Replace the ignition coil assembly with a normal one.
Perform the spark test again.
| Result | Proceed to |
|---|---|
| OK | Replace ignition coil assembly |
| NG | Go to next step |
Inspect the spark plug.
If there is a cylinder in which ignition does not occur, interchange the spark plug of that cylinder and the spark plug of a cylinder in which ignition properly occurs.
Check that sparks occur in the cylinder in which the properly functioning spark plug was installed.
If an ignition coil assembly is struck or dropped, replace it with a new one.
If a spark plug is struck or dropped, replace it with a new one.
Check the camshaft position sensor.
Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>P0340
Check the crankshaft position sensor.
Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>P0335
Connect the 4 injector connectors.
Install the 4 ignition coil assemblies and 4 spark plugs.
Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION
Clear DTCs.
Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
19100P
3.INSPECT SPARK PLUG
Do not use a wire brush for cleaning.
Do not attempt to adjust the electrode gap of a used spark plug.
Perform "Inspection After Repair" after replacing a spark plug.
Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| *a | Body Ground |
Check the electrode.
Using a megohmmeter, measure the insulation resistance.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Spark plug (Terminal part) - Body ground | Always | 10 MΩ or higher |
If a megohmmeter is not available, perform the following simple inspection instead.
Alternative inspection method:
Quickly accelerate the engine to 4000 rpm 5 times.
Remove the spark plug.
Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
Check the spark plug for any damage on its threads and insulator.
If there is damage, replace the spark plug. If not, reinstall the spark plug.
| Manufacturer | Product |
|---|---|
| DENSO | FK20HR-A8 |
Check the spark plug electrode gap.
1.1 mm (0.0433 in.)
If the gap is more than the maximum, replace the spark plug.
0.7 to 0.8 mm (0.0276 to 0.0315 in.)
When adjusting the gap of a new spark plug, bend only the base of the ground electrode. Do not touch the tip. Never attempt to adjust the gap of a used plug.
Clean the spark plugs.
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.
588 kPa (6.0 kgf/cm2, 85 psi)
20 seconds or less
Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.