Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM
RM3250E _56 Audio / Visual / Telematics _038053 NAVIGATION / MULTI INFO DISPLAY _0182280 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The navigation receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Telephone microphone signal is lost.
·

Navigation receiver assembly

·

Map light assembly

·

Telephone microphone assembly

·

Harness or connector



WIRING DIAGRAM

E319203E04
0.875,0.667 1.583,1.188 0.708,0.521 10 false Telephone Microphone Assembly 1.823,0.573 2.26,0.76 0.438,0.188 10 false MCO+ 1.823,1.365 2.281,1.531 0.458,0.167 10 false MACC 1.833,0.979 2.271,1.167 0.438,0.188 10 false MCO- 2.302,0.573 2.5,0.729 0.198,0.156 10 false 14 2.313,0.99 2.51,1.146 0.198,0.156 10 false 13 2.302,1.365 2.5,1.521 0.198,0.156 10 false 15 0.563,2.5 0.813,2.677 0.25,0.177 10 false Q3 0.552,2.656 1.969,2.865 1.417,0.208 10 false Map Light Assembly 0.229,3.385 0.938,3.563 0.708,0.177 10 false *: Shielded 5.677,0.688 6.063,0.854 0.385,0.167 10 false MIN+ 5.667,1.073 6.052,1.24 0.385,0.167 10 false MIN- 5.677,1.479 6.135,1.646 0.458,0.167 10 false MACC 5.677,1.875 6.135,2.042 0.458,0.167 10 false SGND 5.469,0.594 5.604,0.75 0.135,0.156 10 false 5 5.406,1 5.604,1.156 0.198,0.156 10 false 19 5.427,2.5 5.958,2.677 0.531,0.177 10 false G113 5.469,2.646 6.667,3.01 1.198,0.365 10 false Navigation Receiver Assembly 5.49,1.385 5.625,1.542 0.135,0.156 10 false 4 5.427,1.771 5.625,1.927 0.198,0.156 10 false 18 3.406,2.021 3.552,2.156 0.146,0.135 10 false * 4.583,2.031 4.729,2.167 0.146,0.135 10 false *

CAUTION / NOTICE / HINT

NOTICE:

Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E280108C14
0.198,0.917 0.583,1.125 0.385,0.208 2.021,1.323 1.25,1.813 1.25,1.813 1.01,1.813 true 2.167,1.333 2.25,1.896 2.25,1.896 2.406,1.896 true 2.156,1.083 2.292,0.292 2.292,0.292 2.448,0.292 true 0,0 0.313,0.156 0.313,0.156 10 false *a 0.229,0.938 0.583,1.135 0.354,0.198 10 false G113 0.604,1.719 0.958,1.917 0.354,0.198 10 false MIN- 2.469,1.802 3.135,1.979 0.667,0.177 10 false SGND 2.542,0.198 3.031,0.365 0.49,0.167 10 false MACC
*a Component with harness connected
(Navigation Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G113-18 (SGND) - Body ground Always Below 1 Ω
G113-19 (MIN-) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G113-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G113 navigation receiver assembly connector.


b.

Disconnect the Q3 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G113-5 (MIN+) - Q3-14 (MCO+) Always Below 1 Ω
G113-19 (MIN-) - Q3-13 (MCO-) Always Below 1 Ω
G113-4 (MACC) - Q3-15 (MACC) Always Below 1 Ω
G113-5 (MIN+) - Body ground Always 10 kΩ or higher
G113-19 (MIN-) - Body ground Always 10 kΩ or higher
G113-4 (MACC) - Body ground Always 10 kΩ or higher
G113-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL


b.

Check for DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE MAP LIGHT ASSEMBLY