When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for Connected Services (w/ Connected Services Function).
Check the radio automatic station search function by activating it.
Automatic station search function stops on a station.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are not installed.
Do not remove any optional components installed by the customer without his or her consent.
Optional components are installed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the antenna connector from the radio and display receiver assembly.
Turn the ignition switch to ACC with radio and display receiver assembly connector connected.
Turn on the radio and turn into AM mode.
Place a screwdriver, thin wire or other metal object on the radio and display receiver assembly and check that noise can be heard from the speakers.
Noise Occurs.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the RA radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (ANT+) - Body ground | Ignition switch ACC, radio switch on and FM or AM selected | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Remove the antenna connector from the radio and display receiver assembly.
Remove the antenna connector from the No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| RA-3 (MAIN) - 2 | Always | Below 1 Ω |
| RA-5 (ANT+) - 3 | Always | Below 1 Ω |
| RA-3 (MAIN) - Body ground | Always | 10 kΩ or higher |
| RA-5 (ANT+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to No. 1 Amplifier Antenna Assembly) |
Remove the antenna connector from the antenna cord sub-assembly.
Remove the antenna connector from the No. 1 amplifier antenna assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 - 2 | Always | Below 1 Ω |
| 3 - 3 | Always | Below 1 Ω |
| 2 - Body ground | Always | 10 kΩ or higher |
| 3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the No. 1 amplifier antenna assembly is securely installed.
The No. 1 amplifier antenna assembly is installed properly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 amplifier antenna assembly and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA>REMOVAL
Radio broadcasts can be received normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the roof antenna pole sub-assembly and check if radio broadcasts can be received normally.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA POLE>REMOVAL
Radio broadcasts can be received normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG