Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for 2WD)
RM3250E _53 Suspension _038041 FRONT SUSPENSION _0182539 FRONT LOWER SUSPENSION ARM(for 2WD) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for 2WD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43340A 1.INSTALL FRONT LOWER BALL JOINT ASSEMBLY LH

a.
C237856N02
1.594,0.177 2.115,0.177 2.115,0.177 2.625,0.844 true 2.448,2.323 2.75,2.323 false 2.75,2.323 2.906,1.938 false 1.208,0.115 1.615,0.323 0.406,0.208 10 false SST 2.031,2.24 2.438,2.448 0.406,0.208 10 false SST

Using SST and press, press in a new lower ball joint.

SST
09226-10010  
09631-32020  


b.

Install a new snap ring.

NOTICE:

Make sure the snap ring is securely installed in the groove.



Hide 48654F 2.INSTALL FRONT LOWER NO. 1 ARM BUSH LH

a.
C322838N01
2.323,1.188 1.854,0.823 1.854,0.823 2.344,0.823 true 2.313,2.552 2.021,2.813 2.021,2.813 1.865,2.813 true 1.542,0.74 2,0.938 0.458,0.198 10 false SST 1.573,2.719 2.031,2.917 0.458,0.198 10 false SST

Using SST and a press, install a new front lower No. 1 arm bush LH.

SST
09710-14013  (09710-00021)
09710-20011  (09710-06041)
09950-60010  (09951-00610)


Hide 48655E 3.INSTALL FRONT LOWER NO. 2 ARM BUSH LH

a.
C322837C01
0.385,3.979 1.052,3.167 1.052,3.167 0.396,3.479 true 0.635,1.74 0.344,1.344 0.344,1.344 0.677,1.219 true 0.042,1.25 0.5,1.448 0.458,0.198 10 false SST 1.125,3.063 1.583,3.26 0.458,0.198 10 false *a
*a Bush Positioning Protrusion


Using SST and a press, press in a new front lower No. 2 arm bush LH.

SST
09710-14013  (09710-00021)
09950-60010  (09951-00650)

NOTICE:

Press the bush while making sure the bush positioning protrusions are perpendicular to the lower arm as shown in the illustration.



Hide 48626 4.INSTALL FRONT LOWER BALL JOINT ATTACHMENT LH

a.

Install the front lower ball joint attachment LH with the nut and a new cotter pin.

Torque:
140 N*m (1428 kgf*cm, 103 ft.*lbf)


Hide 48069 5.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

C322831C01
0.906,0.76 2.917,0.531 2.917,0.531 2.667,0.771 true 0.469,0.656 0.656,0.656 0.656,0.656 0.708,0.854 true 2.5,1.25 2.417,1.49 2.417,1.49 2.229,1.49 true 3,0.427 3.313,0.625 0.313,0.198 10 true *a 0.135,0.583 0.448,0.781 0.313,0.198 10 true *1 2.021,1.427 2.25,1.625 0.229,0.198 10 true *2
*1 No. 1 Camber Adjusting Cam
*2 No. 2 Camber Adjusting Cam
*a Matchmark


a.

Temporarily install the front lower No. 1 suspension arm sub-assembly LH, and No. 1 and No. 2 camber adjusting cams with the 2 camber adjusting cams and 2 nuts.


b.

Align the matchmarks on the No. 1 camber adjusting cam and No. 2 camber adjusting cam with the corresponding matchmarks on the vehicle frame.


c.
C322830

Install the front lower ball joint attachment LH with the 2 bolts.

Torque:
160 N*m (1632 kgf*cm, 118 ft.*lbf)


Hide 48304 6.INSTALL FRONT NO. 1 SPRING BUMPER SUB-ASSEMBLY

a.
C322839C01
2.26,0.979 2.49,0.771 2.49,0.771 2.677,0.771 true 2.729,0.688 3.188,0.885 0.458,0.198 10 true SST 2.177,1.677 2.635,1.875 0.458,0.198 10 true *a
*a Torque Wrench Fulcrum Length


Using SST, install the front No. 1 spring bumper sub-assembly to the front lower No. 1 suspension arm sub-assembly LH.

SST
09922-10010  

Torque:
Specified tightening torque : 31 N*m (316 kgf*cm, 23 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 112.5 mm (4.4291 in.)) + torque wrench (fulcrum length of 300 mm (11.8110 in.)): 22.5 N*m (229 kgf*cm, 17 ft.*lbf)




Hide 7.TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Temporarily install the front shock absorber with coil spring with the bolt and nut.


Hide 48810 8.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.

Connect the front stabilizer link assembly LH to the front lower No. 1 suspension arm sub-assembly LH with the nut.

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud in place.



Hide 89543 9.CONNECT FRONT SPEED SENSOR LH (w/ ABS)

a.
C326177

Connect the front speed sensor LH with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 51410 10.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY (w/ Engine Under Cover Assembly)

Hide 11.INSTALL FRONT WHEEL

Hide 48069 13.TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Tighten the 2 nuts.

Torque:
210 N*m (2141 kgf*cm, 155 ft.*lbf)


Hide 14.TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

a.

Fix the nut in place and tighten the bolt.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)

NOTICE:

Do not tighten the nut.



Hide 15.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT