Home › Engine / Hybrid System › 1TR-FE FUEL › FUEL INJECTOR
RM3250E _51 Engine / Hybrid System _037999 1TR-FE FUEL _0182609 FUEL INJECTOR A

1TR-FE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>1TR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A346782C01
2.635,1.427 2.885,1.229 2.885,1.229 3.042,1.229 false 3.083,1.135 3.292,1.323 0.208,0.188 10 false *1
*1 O-Ring


Apply a light coat of gasoline or spindle oil to new O-rings, and then install one to each fuel injector assembly.


b.

Apply a light coat of gasoline or spindle oil to the contact surfaces of the fuel delivery pipe and the O-ring of the fuel injector assembly.


c.
A346783C01
0,0 0,0 false
V100135

Turn
V100136

Push


Apply a light coat of gasoline or spindle oil to the O-ring again, and then install the fuel injector assembly to the fuel delivery pipe by turning it right and left.

NOTICE:

Make sure that the O-ring is not cracked or jammed when installing it.



d.

Check that the fuel injector assembly rotates smoothly.

If the fuel injector assembly does not rotate, replace the O-ring.


Hide 23814B 2.INSTALL FUEL DELIVERY PIPE WITH FUEL INJECTOR ASSEMBLY

a.
A346784C01
0.323,0.583 0.323,0.271 0.323,0.271 0.427,0.271 false 0.74,0.677 0.74,0.854 false 0.458,0.167 0.656,0.354 0.198,0.188 10 false *1 0.688,0.875 0.896,1.052 0.208,0.177 10 false *2
*1 O-Ring
*2 Spacer


Apply a light coat of gasoline or spindle oil to new O-rings, and then install one to each spacer.


b.

Install the 4 spacers to the cylinder head.


c.

Install 4 new injector vibration insulators to the cylinder head.


d.

Install the 2 No. 1 delivery pipe spacers to the cylinder head.


e.

Install the fuel delivery pipe together with the 4 fuel injector assemblies, and then temporarily install the fuel delivery pipe with the 2 bolts.

NOTICE:

Do not drop the fuel injector assemblies when installing the fuel delivery pipe.



f.

Check that the fuel injector assemblies rotate smoothly.

If any fuel injector assembly does not rotate, replace its O-ring.


g.

Tighten the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


h.

Install the vacuum hose.


i.

Connect the purge VSV connector.


j.

Connect the 4 fuel injector connectors.


k.

Connect the 4 wire harness clamps.


Hide 23270 3.INSTALL FUEL PRESSURE PULSATION DAMPER ASSEMBLY

Hide 23273H 4.CONNECT NO. 2 FUEL HOSE

a.

Connect the No. 2 fuel hose.


Hide 23271H 5.CONNECT NO. 1 FUEL HOSE

a.

Connect the No. 1 fuel hose.

Click hereEngine / Hybrid System>1TR-FE FUEL>FUEL SYSTEM>PRECAUTION


Hide 22030 6.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 8.INSPECT FOR FUEL LEAK

a.

Make sure that there are no fuel leaks after performing maintenance on the fuel system.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON and turn the GTS on.

NOTICE:

Do not start the engine.



iii.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

iv.

Check that there are no leaks from the fuel system.

If there are fuel leaks, repair or replace parts as necessary.


v.

Turn the ignition switch off.


vi.

Disconnect the GTS from the DLC3.