Home › Engine / Hybrid System › 1TR-FE FUEL › FUEL TANK(for Short Wheelbase)
RM3250E _51 Engine / Hybrid System _037999 1TR-FE FUEL _0182614 FUEL TANK(for Short Wheelbase) A

1TR-FE FUEL  FUEL TANK(for Short Wheelbase)  INSTALLATION  


PROCEDURE

Hide 77213B 1.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.
A349940C01
1.063,0.75 1.323,0.552 1.323,0.552 1.5,0.552 true 0.573,1.104 0.719,1.104 0.719,1.104 1,0.875 true 1.531,0.458 1.781,0.656 0.25,0.198 10 false *a 0.385,1.01 0.563,1.219 0.177,0.208 10 false *b 0.458,2.917 0.854,3.156 0.396,0.24 10 false 180°
*a Protrusion
*b Paint Mark (Red)


Install the fuel tank to filler pipe hose to the fuel tank assembly, and tighten the clamp to secure the hose.

HINT:

Make sure the hose clamp is oriented as shown in the illustration.



Hide 77020A 2.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 77651B 3.INSTALL FUEL TANK CUSHION

a.

Install the 3 fuel tank cushions to the fuel tank assembly.


Hide 77697 4.INSTALL NO. 1 FUEL TANK HEAT INSULATOR

a.

Install the No. 1 fuel tank heat insulator with the 3 No. 2 fuel tank brackets.


Hide 77001A 5.INSTALL FUEL TANK ASSEMBLY

a.

Set the fuel tank assembly on an engine lifter and raise the fuel tank assembly.

NOTICE:

Do not allow the fuel tank assembly to contact the vehicle, especially the differential.



b.

Fold back approximately half of each cushion so that the wire harness can be installed in the step below.


c.

Attach the wire harness to the 6 clamps and connect the fuel sender gauge connector.

NOTICE:

Be careful not to cut the wire harness.



d.

Install the 3 fuel tank bands with the 3 fuel tank band pins and 3 clips.


e.

Connect the 3 fuel tank bands with the 3 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


Hide 77213B 6.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A349939C01
0.823,0.896 1.156,0.479 1.156,0.479 1.302,0.479 true 0.385,1.375 0.521,1.375 0.521,1.375 0.76,1.042 true 0.208,1.281 0.396,1.51 0.188,0.229 10 false *a 1.344,0.385 1.552,0.594 0.208,0.208 10 false *b 0.99,2.063 1.26,2.313 0.271,0.25 10 false 55° 0.177,2.229 0.51,2.469 0.333,0.24 10 false 125° 1.292,0.865 1.49,1.063 0.198,0.198 10 false *c 0.094,0.823 0.281,1.021 0.188,0.198 10 false *d
*a Protrusion
*b Paint Mark (Yellow)
*c 0 to 3 mm (0 to 0.118 in.)
*d 2 to 7 mm (0.0787 to 0.276 in.)


Connect the fuel tank to filler pipe hose to the fuel tank filler pipe sub-assembly, and tighten the clamp to secure the hose.

HINT:

Make sure the hose clamp is oriented as shown in the illustration.



Hide 7.CONNECT FUEL TANK BREATHER HOSE

a.
A349938C01
0.813,1.031 1.083,1.26 1.083,1.26 1.229,1.26 true 1.26,1.167 1.5,1.354 0.24,0.188 10 false *a 0.823,1.771 1.052,1.969 0.229,0.198 10 false *b 0.365,1.906 0.719,2.125 0.354,0.219 10 false 120°
*a Paint Mark
*b Top of Vehicle


Connect the fuel tank breather hose to the fuel tank filler pipe sub-assembly, and slide the clamp to secure the hose.

HINT:

Make sure the hose clamp is oriented as shown in the illustration.



Hide 8.CONNECT FUEL TUBE

NOTICE:

Before installing the tube connectors to the pipes, check the connectors for damage and foreign matter.


a.

Connect the fuel tank main tube sub-assembly, fuel tank return tube and vent line tube.

Click hereEngine / Hybrid System>1TR-FE FUEL>FUEL SYSTEM>PRECAUTION


Hide 77289B 9.INSTALL NO. 3 FUEL TUBE CLAMP

a.

Install the No. 3 fuel tube clamp to the fuel tube.


Hide 77641A 10.INSTALL NO. 1 FUEL TANK PROTECTOR

a.

Install the fuel tank protector to the fuel tank assembly with the 5 nuts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 77310A 11.INSTALL FUEL TANK CAP ASSEMBLY

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION