Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR DOOR SPEAKER(for Smart Cab)
RM3250E _56 Audio / Visual / Telematics _038052 AUDIO / VIDEO _0182783 REAR DOOR SPEAKER(for Smart Cab) A

AUDIO / VIDEO  REAR DOOR SPEAKER(for Smart Cab)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 86160B 1.INSTALL REAR SPEAKER ASSEMBLY

a.

Install a nose piece to an air riveter or hand riveter. Then insert the mandrel part of a new φ4 mm waterproof rivet into the nose piece.


b.
E322688

Using an air riveter or hand riveter, install the rear speaker assembly with 3 new rivets.

NOTICE:
·
B171664C14
1.229,1.104 1.083,1.635 1.083,1.635 1.24,2.198 false 1.083,1.635 0.813,1.635 false 1.792,0.896 2.031,1.635 2.031,1.635 1.75,2.521 true 2.031,1.635 2.313,1.635 false 2.26,0.604 2.563,0.813 0.302,0.208 10 false *a 2.26,2.448 2.583,2.688 0.323,0.24 10 false *b 2.365,1.531 2.677,1.729 0.313,0.198 10 false *1 0.573,1.552 0.844,1.74 0.271,0.188 10 false *2
*1 Mandrel
*2 Riveter
*a INCORRECT
*b CORRECT


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B172390C15
0.719,0.104 1.021,0.104 false 0.802,1.146 1,1.146 false 0.802,2.438 1,2.438 false 2.313,0.563 2.646,0.792 0.333,0.229 10 false *a 2.313,2.76 2.625,2.99 0.313,0.229 10 false *b 1.052,2.365 1.354,2.635 0.302,0.271 10 false *1 2.313,1.573 2.625,1.823 0.313,0.25 10 false *a 1.052,1.073 1.333,1.26 0.281,0.188 10 false *1 1.052,0.031 1.365,0.24 0.313,0.208 10 false *1
*1 Riveter
*a INCORRECT
*b CORRECT


Confirm that the rivets are seated properly against the speaker.

·

Do not tilt the riveter when installing the rivet to the speaker.

·

Do not leave any space between the rivet head and speaker.

·
B172391C14
0.729,0.646 0.927,0.646 false 0.719,2.156 0.927,2.156 false 2.292,1.042 2.615,1.281 0.323,0.24 10 false *a 2.292,2.469 2.635,2.688 0.344,0.219 10 false *b 0.979,0.563 1.292,0.792 0.313,0.229 10 false *1 0.979,2.073 1.271,2.281 0.292,0.208 10 false *1
*1 Riveter
*a INCORRECT
*b CORRECT


Do not leave any space between the speaker and door. Firmly hold together the 2 items while installing the rivet.




c.

Connect the connector.


Hide 67674A 2.INSTALL REAR DOOR FRAME GARNISH LH

Hide 67604 3.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 73220 4.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 73233 5.INSTALL OUTER LAP BELT ANCHOR COVER

Hide 73178A 6.INSTALL SEAT BELT ANCHOR COVER CAP

Hide 7.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).