Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR(for Smart Cab) › 2015.06–2016.03
RM3250E _59 Vehicle Exterior _038077 DOOR / HATCH _0186371 REAR DOOR(for Smart Cab) A

DOOR / HATCH  REAR DOOR(for Smart Cab)  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 67003C 1.INSTALL REAR DOOR PANEL CUSHION

a.
B414959

Attach the claw to install a new rear door panel cushion.


Hide 67897H 2.INSTALL REAR DOOR CUSHION

a.
B414958

Attach the claw to install a new rear door cushion.


Hide 67837C 3.INSTALL REAR DOOR DUST PROOF SEAL

a.
B414957

Attach the claw to install 2 new rear door dust proof seals.


Hide 67872F 4.INSTALL ACCESS PANEL WEATHERSTRIP LH

a.
B414960

Attach the clip.


b.
B414961

Attach the clip.


c.

Attach the clip and remove the peeling paper from double-sided tape and press the double-sided tape to the rear side of the access door panel.

B414962C01
0,0 0,0 false
V100155

Double-sided Tape - -



d.
B414963C01
0,0 0,0 false
V100155

Double-sided Tape


Remove the peeling paper from double-sided tape and press the double-sided tape to the upper side of the access door panel.


e.

Remove the peeling paper from double-sided tape and press the double-sided tape to the corner of the access door panel.

B414964C01
0,0 0,0 false
V100155

Double-sided Tape - -



f.
B414965C01
2.156,3.271 2.375,3.271 2.375,3.271 2.51,3.073 true 2.542,2.531 2.615,2.396 2.615,2.396 2.698,2.396 false 2.74,2.313 3.052,2.51 0.313,0.198 10 false *b 1.948,3.156 2.26,3.354 0.313,0.198 10 false *a
*a Mold Portion
*b Lower Corner Portion
V113147

Install in this Direction


Insert the mold portion to the lower corner portion to install a new access panel weatherstrip LH.


Hide 68640E 5.INSTALL ACCESS PANEL CHECK ASSEMBLY LH

a.

Apply MP grease to the sliding area of the access panel check assembly LH.


b.

When reusing a bolt:

i.

Clean the threads of the bolt (B) with non-residue solvent.


ii.

Apply adhesive to the threads of the bolt (B).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




c.
B414955C02
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


Install the access panel check assembly LH with the 2 bolts (A) and bolt (B).

Torque:
Bolt (A) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt (B) : 30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 69410D 6.INSTALL ACCESS PANEL LOCK STRIKER PLATE ASSEMBLY

a.
B414954

Using a T40 "TORX" socket wrench, install the access panel lock striker plate assembly with the 2 screws

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 84233 7.INSTALL FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

Hide 69780C 8.INSTALL ACCESS PANEL LOCK CANCEL LEVER ASSEMBLY LH

a.

Apply MP grease to the rotating and sliding areas of the access panel lock cancel lever assembly LH.


b.

When reusing a screw:

i.

Clean the threads of the screw with non-residue solvent.


ii.

Apply adhesive to the threads of the screw.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.




c.
B414953

Install the access panel lock cancel lever assembly LH with the 2 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 62742 9.INSTALL QUARTER WINDOW WEATHERSTRIP LH

a.

Remove any non-drying sealer on the body with non-residue solvent.


b.
B414966C01
3.01,1 2.885,1 2.885,1 2.76,0.688 false 2.469,1.51 2.469,1.177 2.469,1.177 2.667,1.177 false 2.708,1.094 3.021,1.292 0.313,0.198 10 false *a 3.052,0.917 3.365,1.115 0.313,0.198 10 false *b
*a Paint Mark
*b Mark Position


Align the paint mark with the position on the access panel LH flange and install a new quarter window weatherstrip LH.

NOTICE:
·

Always align the paint mark when installing the part. If the paint mark position is out of place, coolant leaks may occur.

·

After the installation, check that the corners are properly installed.



HINT:

To easily install the weatherstrip, first install the area with the paint mark as shown in the illustration. Then install the part toward the corners and push any excess length into the corners.



Hide 69640D 11.INSTALL ACCESS PANEL LOCK REMOTE CONTROL ASSEMBLY LH

a.

Apply MP grease to the rotating and sliding areas of the access panel lock remote control assembly LH.


b.
B414951

Install the access panel lock remote control assembly LH with the 3 nuts.


Hide 69390D 12.INSTALL LOWER ACCESS PANEL LOCK ASSEMBLY LH

Hide 69360L 13.INSTALL UPPER ACCESS PANEL LOCK ASSEMBLY LH

Hide 69208K 14.INSTALL ACCESS PANEL INSIDE HANDLE SUB-ASSEMBLY LH

a.
B414967C01
0.635,0.365 0.75,0.229 0.75,0.229 0.896,0.229 true 0.604,1.823 0.781,1.823 0.781,1.823 0.906,1.656 true 0.479,1.729 0.677,1.927 0.198,0.198 10 true *1 0.875,0.146 1.073,0.344 0.198,0.198 10 true *1
*1 Snap
V100135

Bolt
V100136

Nut
V100137

Order of Installation
V113147

Install in this Direction


Install the nut, bolt and access panel inside handle sub-assembly LH.


b.

Attach the snap as shown in the illustration.


Hide 16.INSTALL SCREW GROMMET

a.
B414949

Attach the claw to install 3 new screw grommets.


Hide 67674A 17.INSTALL REAR DOOR FRAME GARNISH LH

a.
B414968

Attach the clip to install the rear door frame garnish LH.


b.
B414946C02
0,0 0,0 false
V100135

Screw
V100136

Clip


Install the clip and 3 screws.


Hide 73220 18.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 73178A 19.INSTALL SEAT BELT ANCHOR COVER CAP

a.
B408997C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the guide and claw to install the seat belt anchor cover cap as shown in the illustration.


Hide 67604 20.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B414970C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Attach the guide as shown in the illustration.


b.
B414971

Attach the claw and clip to install the rear door trim board sub-assembly LH.


c.
B414941

Connect the front seat outer belt floor anchor with the bolt.


Hide 73233 21.INSTALL LAP BELT OUTER ANCHOR COVER

a.
B414940

Attach the claw to install the lap belt outer anchor cover.


Hide 22.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION