Home › Engine / Hybrid System › 1TR-FE ENGINE MECHANICAL › ENGINE UNIT
RM3250E _51 Engine / Hybrid System _037998 1TR-FE ENGINE MECHANICAL _0184012 ENGINE UNIT A

1TR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 83530 2.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89422 4.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 12108 5.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap sub-assembly.


b.

Remove the gasket from the oil filler cap sub-assembly.


Hide 12204 6.REMOVE PCV VALVE SUB-ASSEMBLY

Hide 11301M 7.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11301M 8.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 11301K 9.REMOVE CRANKSHAFT POSITION SENSOR

Hide 11101J 10.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Intake Side)

Hide 11101J 11.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Exhaust Side)

Hide 11201 12.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12233 13.REMOVE NO. 1 VENTILATION CONNECTOR

a.
A340619

Remove the 2 bolts and No. 1 ventilation connector from the cylinder head cover sub-assembly.


Hide 16321 14.REMOVE WATER INLET

Hide 16331A 15.REMOVE THERMOSTAT

Hide 13471 16.REMOVE CRANKSHAFT PULLEY

Hide 12144 17.REMOVE OIL PAN COVER SILENCER

Hide 12102A 18.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15104 19.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 12101 20.REMOVE OIL PAN SUB-ASSEMBLY

Hide 11421 21.REMOVE OIL PAN STUD BOLT

NOTICE:

If a oil pan stud bolt is deformed or its threads are damaged, replace it.


Hide 16620D 22.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 11302 23.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 16100 24.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 11303A 25.REMOVE TIMING CHAIN CASE OIL SEAL

Hide 26.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A336450C01
0.427,2 0.594,2 0.594,2 0.885,2.323 true 2.896,2.031 2.76,2.031 2.76,2.031 2.49,2.365 true 2.885,3.75 2.75,3.75 2.75,3.75 1.771,3.917 true 1.833,4.031 2.063,4.302 2.063,4.302 2.063,4.417 true 2.698,0.938 2.052,1.083 2.052,1.083 2.708,0.698 true 1.125,0.573 1.333,1.281 1.333,1.281 1,0.781 true 2.927,3.646 3.125,3.875 0.198,0.229 10 false *1 1.281,1.302 1.479,1.51 0.198,0.208 10 true *a 1.052,0.042 1.24,0.24 0.188,0.198 10 true *b 1.76,3.313 1.958,3.5 0.198,0.188 10 true *c 1.865,0.99 2.063,1.198 0.198,0.208 10 true *a 2.938,1.917 3.135,2.125 0.198,0.208 10 true *a 0.229,1.885 0.427,2.094 0.198,0.208 10 true *a 1.979,4.427 2.177,4.635 0.198,0.208 10 true *a
*1 Crankshaft Pulley Set Key
*a Timing Mark
*b Approximately 13°
*c Approximately 30°


Temporarily install the crankshaft pulley bolt.


b.

Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

HINT:

If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.



c.

Remove the crankshaft pulley bolt.


Hide 11204 27.REMOVE CYLINDER HEAD COVER CONNECTOR SUB-ASSEMBLY

a.
A336454

Remove the 2 bolts and cylinder head cover connector sub-assembly.


b.

Remove the No. 2 camshaft bearing cap oil hole gasket and 3 No. 3 camshaft bearing cap oil hole gaskets from the No. 1 camshaft bearing cap.


Hide 13566B 28.REMOVE TIMING CHAIN GUIDE

a.
A336451C01
0.646,1.729 0.875,1.729 0.875,1.729 1.552,1.063 true 0.438,1.625 0.635,1.813 0.198,0.188 10 false *1
*1 O-Ring


Remove the 2 bolts, timing chain guide and O-ring.


Hide 13540 29.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
A101303C25
1.854,1.531 2.104,1.708 2.104,1.708 2.24,1.708 true 2.323,0.781 2.552,0.344 2.552,0.344 2.677,0.344 true 0.563,1.854 0.563,1.521 false 2.26,1.615 2.49,1.792 0.229,0.177 10 false *b 0.5,1.875 0.698,2.063 0.198,0.188 10 false *c 2.729,0.25 2.917,0.458 0.188,0.208 10 false *a
*a Plunger
*b Stopper Plate
*c Hexagon Wrench


·

When the No. 1 chain tensioner assembly is removed, do not rotate the crankshaft.

·

When the chain is removed and the camshaft needs to be rotated, rotate the crankshaft 90° to the right.



a.

Move the stopper plate upward to release the lock and push the plunger deep into the tensioner.


b.

Move the stopper plate downward to set the lock and insert a hexagon wrench into the stopper plate hole.


c.
A340032

Remove the bolt, nut, No. 1 chain tensioner assembly and gasket.


Hide 13559 30.REMOVE CHAIN TENSIONER SLIPPER

a.
A340034

Remove the bolt and chain tensioner slipper.


Hide 13561 31.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A340036

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13506 32.REMOVE CHAIN SUB-ASSEMBLY

Hide 13521 33.REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET

a.
A353227

Remove the crankshaft timing gear or sprocket from the crankshaft.


Hide 19315A 34.REMOVE CRANK POSITION SENSOR ROTOR

a.
A353228

Remove the crank position sensor rotor from the crankshaft.


Hide 13471A 35.REMOVE CRANKSHAFT PULLEY SET KEY

a.

Remove the 2 crankshaft pulley set keys from the crankshaft.


Hide 13516 36.REMOVE OIL JET

a.

Remove the bolt, oil jet and gasket.


Hide 13801 40.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 41.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 13050 43.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13050 44.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 45.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13070A 46.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11101 47.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 15678A 49.REMOVE OIL CONTROL VALVE FILTER

a.
A101413

Using an 8 mm hexagon wrench, remove the screw plug.


b.

Remove the oil control valve filter and gasket.


Hide 15601 50.REMOVE OIL FILTER SUB-ASSEMBLY

Hide 15600A 51.REMOVE OIL FILTER UNION

a.
A349767

Using a 27 mm socket wrench, remove the oil filter union.


Hide 15609 52.REMOVE OIL FILTER BRACKET SUB-ASSEMBLY

a.
A349768C01
2.25,1.833 2.083,1.833 2.083,1.833 1.917,1.167 true 1.396,1 1.25,0.417 1.25,0.417 1.083,0.417 true 2.583,0.25 2.417,0.25 2.417,0.25 2.25,0.698 true 2.25,1.75 2.5,1.917 0.25,0.167 10 true *1 0.917,0.333 1.167,0.5 0.25,0.167 10 true *2 2.583,0.167 2.833,0.333 0.25,0.167 10 true *3
*1 Union Bolt
*2 Nut
*3 Oil Filter Bracket Straight Screw Plug


Remove the union bolt, gasket and O-ring.


b.

Remove the nut, oil filter bracket sub-assembly and O-ring.


c.

Remove the oil filter bracket straight screw plug and gasket from the oil filter bracket sub-assembly.


Hide 11381 53.REMOVE REAR ENGINE OIL SEAL RETAINER

a.

Remove the 6 bolts.


b.
A349769C01
0.5,1.75 0.667,1.75 0.667,1.75 1.531,1.115 true 0.333,1.677 0.646,1.833 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip taped, pry out the rear engine oil seal retainer.

HINT:

Tape the screwdriver tip before use.



Hide 11381A 54.REMOVE REAR ENGINE OIL SEAL

a.
A346836C01
1.74,1.958 0.75,1.958 0.75,1.958 1.052,1.531 true 1.76,1.052 2.146,0.844 2.146,0.844 2.323,0.844 true 2.354,0.74 2.552,0.948 0.198,0.208 10 false *a 0.542,1.854 0.74,2.063 0.198,0.208 10 false *b
*a Protective Tape
*b Wooden Blocks


Place the rear engine oil seal retainer on wooden blocks.


b.

Using a screwdriver with its tip taped and a hammer, tap out the rear engine oil seal.

HINT:

Tape the screwdriver tip before use.