Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM3250E _52 Drivetrain _038037 VF2CM TRANSFER / 4WD / AWD _0184153 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

VF2CM TRANSFER / 4WD / AWD  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P17AC  Transfer Shift Motor Limit Switch Circuit  


DESCRIPTION

When the transfer switches modes, the TL1, TL2 and TL3 terminals of the limit switch are in one of the ON/OFF combinations listed in the table below.

Terminal When H2 Switching between H2 and H4 When H4 Switching between H4 and L4 When L4
TL1 ON (GND) ON (GND) OFF (OPEN) OFF (OPEN) OFF (OPEN)
TL2 OFF (OPEN) OFF (OPEN) OFF (OPEN) ON (GND) ON (GND)
TL3 OFF (OPEN) ON (GND) ON (GND) ON (GND) OFF (OPEN)

A malfunction is detected depending on the combination of the 3 circuits that make up the limit switch of the transfer shift actuator assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
P17AC Transfer Shift Motor Limit Switch Circuit
·

Diagnosis Condition: Directly after the ignition switch is turned to ON, or while switching between H2 and H4 or while switching between H4 and L4 (transfer shift motor operating) with the ignition switch turned to ON

·

Malfunction Status: The combination of TL1, TL2 and TL3 does not match the pattern

·

Malfunction Time: 0 seconds

·

Other: 1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer shift actuator assembly



WIRING DIAGRAM

C325621E02
5.417,0.302 5.729,0.5 0.313,0.198 10 false IG 4.698,0.771 5.01,0.969 0.313,0.198 10 false 11 4.969,0.792 5.427,0.99 0.458,0.198 10 false TL1 4.969,1.531 5.427,1.729 0.458,0.198 10 false TL2 4.979,2.219 5.438,2.417 0.458,0.198 10 false TL3 4.719,1.531 5.031,1.729 0.313,0.198 10 false 10 4.771,2.198 4.927,2.396 0.156,0.198 10 false 9 3.438,0.76 3.594,0.958 0.156,0.198 10 false 3 3.427,1.531 3.583,1.729 0.156,0.198 10 false 4 3.427,2.208 3.583,2.406 0.156,0.198 10 false 5 3.083,0.781 3.542,0.979 0.458,0.198 10 false TL1 3.094,1.531 3.552,1.729 0.458,0.198 10 false TL2 3.094,2.219 3.552,2.417 0.458,0.198 10 false TL3 2,2.563 2.833,2.75 0.833,0.188 10 false Limit Switch 0.99,2.198 1.146,2.396 0.156,0.198 10 false 6 1.219,2.198 1.833,2.396 0.615,0.198 10 false GND1 1.073,3.24 3.156,3.438 2.083,0.198 10 false Transfer Shift Actuator Assembly 1.083,3.052 1.542,3.25 0.458,0.198 10 false C41 4.698,3.24 6.344,3.438 1.646,0.198 10 false 4 Wheel Drive Control ECU 4.677,3.073 5.135,3.271 0.458,0.198 10 false C39

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)
a.

Disconnect the C39 4 wheel drive control ECU connector.


b.

Disconnect the C41 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-11 (TL1) - C41-3 (TL1) Always Below 1 Ω
C39-10 (TL2) - C41-4 (TL2) Always Below 1 Ω
C39-9 (TL3) - C41-5 (TL3) Always Below 1 Ω
C41-6 (GND1) - Body ground Always Below 1 Ω
C39-11 (TL1) or C41-3 (TL1) - Body ground Always 10 kΩ or higher
C39-10 (TL2) or C41-4 (TL2) - Body ground Always 10 kΩ or higher
C39-9 (TL3) or C41-5 (TL3) - Body ground Always 10 kΩ or higher
C39-11 (TL1) - C41-4 (TL2) and C41-5 (TL3) Always 10 kΩ or higher
C39-10 (TL2) - C41-3 (TL1) and C41-5 (TL3) Always 10 kΩ or higher
C39-9 (TL3) - C41-3 (TL1) and C41-4 (TL2) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK 4 WHEEL DRIVE CONTROL ECU (ECU OUTPUT VOLTAGE)
a.
C325622C06
1.5,0.313 1.875,0.563 0.375,0.25 2.198,1.573 2.729,0.917 true 1.844,1.573 2.219,0.896 true 1.635,1.573 0.917,0.99 true 0.24,0.156 0.552,0.354 0.313,0.198 10 false *a 1.552,0.354 2.01,0.552 0.458,0.198 10 false C41 0.656,0.823 1.115,1.021 0.458,0.198 10 false TL1 2.073,0.677 2.531,0.875 0.458,0.198 10 false TL2 2.656,0.719 3.115,0.917 0.458,0.198 10 false TL3
*a Front view of wire harness connector
(to Transfer Shift Actuator Assembly)


Disconnect the C41 transfer shift actuator assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C41-3 (TL1) - Body ground Ignition switch ON 10 to 14 V
C41-4 (TL2) - Body ground Ignition switch ON 10 to 14 V
C41-5 (TL3) - Body ground Ignition switch ON 10 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPLACE 4 WHEEL DRIVE CONTROL ECU