Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM3250E _52 Drivetrain _038037 VF2CM TRANSFER / 4WD / AWD _0184153 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

VF2CM TRANSFER / 4WD / AWD  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P279E  Four Wheel Drive (4WD) Range Signal Circuit Range / Performance  


DESCRIPTION

When the transfer position switch is switched, the 2-4 terminal and LO terminal change to one of the following ON/OFF combinations listed in the table below.

Terminal H2 Between H2 and H4 H4 Between H4 and L4 L4
2-4 ON OFF ON OFF OFF
LO OFF OFF ON OFF ON

This DTC is detected if the transfer position switch 2-4 terminal and LO terminal signals are simultaneously received.

DTC No. Detection Item DTC Detection Condition Trouble Area
P279E Four Wheel Drive (4WD) Range Signal Circuit Range / Performance
·

Diagnosis Condition: Ignition switch turned to ON

·

Malfunction Status: The ON/OFF combination of the 2-4 terminal and LO terminal does not match the pattern

·

Malfunction Time: 60 seconds or more

·

Other: 1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer position switch



WIRING DIAGRAM

C325754E08
0.917,2.156 2.521,2.344 1.604,0.188 10 false Transfer Position Switch 0.917,1.979 1.375,2.177 0.458,0.198 10 false G12 2.833,0.802 3.292,1 0.458,0.198 10 false 2-4 2.865,1.427 3.177,1.625 0.313,0.198 10 false LO 3.146,0.802 3.302,1 0.156,0.198 10 false 5 3.135,1.438 3.292,1.635 0.156,0.198 10 false 2 1.563,0.938 1.969,1.115 0.406,0.177 10 false H2 2.073,1.125 2.385,1.323 0.313,0.198 10 false H4 1.604,1.531 1.917,1.729 0.313,0.198 10 false L4 1,1.115 1.458,1.313 0.458,0.198 10 false GND 0.802,1.115 0.958,1.313 0.156,0.198 10 false 4 5.063,0.771 5.375,0.969 0.313,0.198 10 false 14 5.333,0.792 5.792,0.99 0.458,0.198 10 false 2-4 5.063,1.417 5.375,1.615 0.313,0.198 10 false 13 5.344,1.406 5.656,1.604 0.313,0.198 10 false LO 5.052,2.198 6.76,2.406 1.708,0.208 10 false 4 Wheel Drive Control ECU 5.063,2.031 5.521,2.229 0.458,0.198 10 false C39 5.854,0.24 6.167,0.438 0.313,0.198 10 false IG

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER POSITION SWITCH)
a.

Disconnect the C39 4 wheel drive control ECU connector.


b.

Disconnect the G12 transfer position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-14 (2-4) - G12-5 (2-4) Always Below 1 Ω
C39-13 (LO) - G12-2 (LO) Always Below 1 Ω
G12-4 (GND) - Body ground Always Below 1 Ω
C39-14 (2-4) or G12-5 (2-4) - Body ground Always 10 kΩ or higher
C39-13 (LO) or G12-2 (LO) - Body ground Always 10 kΩ or higher
C39-14 (2-4) or G12-5 (2-4) - C39-13 (LO) or G12-2 (LO) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK TRANSFER POSITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TRANSFER POSITION SWITCH
a.
C326243C02
0.125,1.573 0.5,1.823 0.375,0.25 1.427,2.104 0.865,2.74 true 1.875,2.094 2.5,2.771 true 0.219,0.385 0.531,0.583 0.313,0.198 10 false *a 0.188,1.625 0.51,1.823 0.323,0.198 10 false G12 0.76,2.75 1.219,2.948 0.458,0.198 10 false 2-4 2.469,2.802 2.781,3 0.313,0.198 10 false LO
*a Component with harness connected
(Transfer Position Switch)


Remove the transfer position switch with its connector still connected.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G12-5 (2-4) - Body ground Ignition switch ON
H2 position
Below 1.5 V
Ignition switch ON
H4 position
Below 1.5 V
Ignition switch ON
L4 position
10 to 14 V
G12-2 (LO) - Body ground Ignition switch ON
H2 position
10 to 14 V
Ignition switch ON
H4 position
Below 1.5 V
Ignition switch ON
L4 position
Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPLACE TRANSFER POSITION SWITCH