Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM3250E _52 Drivetrain _038037 VF2CM TRANSFER / 4WD / AWD _0184153 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

VF2CM TRANSFER / 4WD / AWD  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P17C7  Front Differential Oil Temperature Sensor Circuit Low  


DESCRIPTION

This DTC is output when a short to ground in the oil temperature sensor is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area
P17C7 Front Differential Oil Temperature Sensor Circuit Low
·

Diagnosis Condition: Ignition switch turned to ON

·

Malfunction Status: Short to ground in the oil temperature sensor

·

Malfunction Time: 1 second or more

·

Other: 1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Oil temperature sensor



WIRING DIAGRAM

C325709E08
5.708,0.25 6.167,0.448 0.458,0.198 10 false VCC 5.01,1.25 5.323,1.448 0.313,0.198 10 false DT 4.781,1.25 4.958,1.521 0.177,0.271 10 false 5 4.75,2.052 5.063,2.25 0.313,0.198 10 false 25 5.021,2.031 5.635,2.229 0.615,0.198 10 false DGND 2.938,2.052 3.552,2.25 0.615,0.198 10 false DGND 3.438,2.063 3.594,2.26 0.156,0.198 10 false 2 1.74,2.052 2.052,2.25 0.313,0.198 10 false DT 1.51,2.042 1.667,2.24 0.156,0.198 10 false 1 1.844,2.667 2.156,2.865 0.313,0.198 10 false E1 1.833,2.865 3.469,3.042 1.635,0.177 10 false Oil Temperature Sensor 5.042,3.25 5.5,3.448 0.458,0.198 10 false C39 5.052,3.417 6.76,3.708 1.708,0.292 10 false 4 Wheel Drive Control ECU

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND OIL TEMPERATURE SENSOR - BODY GROUND)
a.

Disconnect the C39 4 wheel drive control ECU connector.


b.

Disconnect the E1 oil temperature sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-5 (DT) or E1-1 (DT) - Body ground Always 10 kΩ or higher
C39-25 (DGND) or E1-2 (DGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT OIL TEMPERATURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT OIL TEMPERATURE SENSOR
a.

Disconnect the E1 oil temperature sensor connector.


b.
C325714C02
1.302,1.865 0.74,2.563 true 2.083,1.865 2.76,2.49 true 0.125,0.156 0.438,0.354 0.313,0.198 10 false *a 0.49,2.594 1.104,2.792 0.615,0.198 10 false DGND 2.74,2.521 3.052,2.719 0.313,0.198 10 false DT
*a Component without harness connected
(Oil Temperature Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (DT) - 2 (DGND) Always 120 to 240 kΩ



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG