Home › Drivetrain › VF2CM TRANSFER / 4WD / AWD › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM
RM3250E _52 Drivetrain _038037 VF2CM TRANSFER / 4WD / AWD _0184153 TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM C

VF2CM TRANSFER / 4WD / AWD  TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM  P17A9  Transfer Shift Motor Control Circuit Low  


DESCRIPTION

This DTC is output when a short to ground in the transfer shift motor and A.D.D. shift motor* drive circuit is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area
P17A9 Transfer Shift Motor Control Circuit Low
·

Diagnosis Condition: Directly after the ignition switch is turned to ON, or while the ignition switch is turned to ON (transfer shift motor not operating)

·

Malfunction Status: Short to ground in the transfer shift motor and A.D.D. shift motor* drive circuits

·

Malfunction Time: 0.5 seconds or more (after the ignition switch is turned to ON, 0.05 seconds or more)

·

Other: 1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Transfer shift actuator assembly

·

A.D.D. actuator (differential motor actuator assembly)*



*: w/ A.D.D. Actuator


WIRING DIAGRAM

C326380E02
1.938,2.063 2.396,2.26 0.458,0.198 10 false TM1 1.969,2.75 2.427,2.948 0.458,0.198 10 false TM2 0.802,2.438 1.635,2.75 0.833,0.313 10 false Transfer Shift Motor 0.406,3.354 0.865,3.552 0.458,0.198 10 false C41 0.448,3.563 2.542,3.74 2.094,0.177 10 false Transfer Shift Actuator Assembly 2.302,2.083 2.458,2.281 0.156,0.198 10 false 2 4.167,2.083 4.323,2.281 0.156,0.198 10 false 8 4.385,2.083 4.844,2.281 0.458,0.198 10 false TM1 4.188,2.75 4.344,2.948 0.156,0.198 10 false 7 4.365,2.75 4.823,2.948 0.458,0.198 10 false TM2 4.156,4.865 4.313,5.063 0.156,0.198 10 false 2* 4.365,4.854 4.823,5.052 0.458,0.198 10 false DM1 4.146,5.521 4.302,5.719 0.156,0.198 10 false 6* 4.365,5.51 4.823,5.708 0.458,0.198 10 false DM2 1.948,4.844 2.406,5.042 0.458,0.198 10 false DM1 2.313,4.844 2.469,5.042 0.156,0.198 10 false 1 1.948,5.51 2.406,5.708 0.458,0.198 10 false DM2 2.323,5.521 2.479,5.719 0.156,0.198 10 false 2 0.49,6.177 0.948,6.375 0.458,0.198 10 false C7 0.5,6.375 3.167,6.76 2.667,0.385 10 true A.D.D. Actuator (Differential Motor Actuator Assembly)* 4.333,7.438 4.792,7.635 0.458,0.198 10 false C40 4.667,7.427 6.365,7.625 1.698,0.198 10 false 4 Wheel Drive Control ECU 6.177,5.875 6.49,6.073 0.313,0.198 10 false IG 5.521,0.76 5.833,0.958 0.313,0.198 10 false IG 5.49,2.417 5.927,2.604 0.438,0.188 10 false RY1-1 5.49,3.104 6.26,3.302 0.771,0.198 10 false RY1-2 5.469,5.188 6.24,5.385 0.771,0.198 10 false RY2-1 5.469,5.865 6.24,6.063 0.771,0.198 10 false RY2-2 0.833,5.177 1.604,5.615 0.771,0.438 10 false A.D.D. Shift Motor 2.323,2.76 2.479,2.958 0.156,0.198 10 false 1 3.135,4.875 3.292,5.073 0.156,0.198 10 false * 3.146,5.563 3.302,5.76 0.156,0.198 10 false * 0.427,7.219 1.885,7.427 1.458,0.208 10 false *: w/ A.D.D. Actuator

PROCEDURE

1.CHECK ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR OR A.D.D. SHIFT MOTOR)
a.

Disconnect the C40 4 wheel drive control ECU connector.


b.
C142292C07
1.563,0.635 1.948,0.917 0.385,0.281 1.719,2.26 2.094,2.885 true 1.969,2.25 2.625,2.896 true 1.365,2.25 1.073,2.802 true 1.417,1.771 1.125,1.063 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 2.5,2.927 2.958,3.125 0.458,0.198 10 false TM1 1.99,2.938 2.448,3.135 0.458,0.198 10 false TM2 0.99,0.865 1.448,1.063 0.458,0.198 10 false DM1 0.885,2.865 1.344,3.063 0.458,0.198 10 false DM2 1.635,0.698 2.094,0.896 0.458,0.198 10 false C40 1.292,0.854 1.604,1.052 0.313,0.198 10 false *A 1.198,2.854 1.51,3.052 0.313,0.198 10 false *A
*A w/ A.D.D. Actuator
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Transfer shift actuator assembly side:
Tester Connection Condition Specified Condition
C40-8 (TM1) or C40-7 (TM2) - Body ground Always 10 kΩ or higher

A.D.D. actuator (differential motor actuator assembly) side (w/ A.D.D. Actuator):
Tester Connection Condition Specified Condition
C40-2 (DM1) or C40-6 (DM2) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK A
NG (transfer shift actuator assembly side) B
NG (A.D.D. actuator (differential motor actuator assembly) side) (w/ A.D.D. Actuator) C



A

REPLACE 4 WHEEL DRIVE CONTROL ECU

B

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)

C

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the C40 4 wheel drive control ECU connector.


b.

Disconnect the C41 transfer shift actuator assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C40-8 (TM1) or C41-2 (TM1) - Body ground Always 10 kΩ or higher
C40-7 (TM2) or C41-1 (TM2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU AND DIFFERENTIAL MOTOR ACTUATOR ASSEMBLY - BODY GROUND)
a.

Disconnect the C40 4 wheel drive control ECU connector.


b.

Disconnect the C7 A.D.D. actuator (differential motor actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C40-2 (DM1) or C7-1 (DM1) - Body ground Always 10 kΩ or higher
C40-6 (DM2) or C7-2 (DM2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR