Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2015.06–2016.03
RM3250E _58 Vehicle Interior _038068 METER / GAUGE / DISPLAY _0184171 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

w/ ABS:

The combination meter assembly receives vehicle speed signals from the brake actuator assembly (skid control ECU) via the CAN communication line. The wheel speed sensors output voltages that vary according to the vehicle speed. The brake actuator assembly (skid control ECU) supplies power to the wheel speed sensors. The brake actuator assembly (skid control ECU) calculates the vehicle speed based on the pulses of the voltage.


w/o ABS:

The combination meter assembly receives vehicle speed signals from the speedometer sensor. The wheel speed sensors output voltages that vary according to the vehicle speed. The speedometer sensor calculates the vehicle speed based on the pulses of the voltage.


WIRING DIAGRAM

E255800E18
4.771,2.563 6.99,2.813 2.219,0.25 10 false Combination Meter Assembly 1.146,2.552 2.813,2.99 1.667,0.438 10 false Brake Actuator Assembly (Skid Control ECU) 0.802,3.375 3.563,3.656 2.76,0.281 10 false : CAN Communication Line 0.083,0.104 2.844,0.385 2.76,0.281 12 false w/ ABS:

E322205E01
5.479,3.031 6.719,3.385 1.24,0.354 10 false Combination Meter Assembly 1.313,3.031 2.927,3.417 1.615,0.385 10 false C62 1.313,3.198 2.927,3.583 1.615,0.385 10 false Speedometer Sensor 3.885,2.083 5.5,2.469 1.615,0.385 10 false 2 3.885,1.365 5.5,1.75 1.615,0.385 10 false 3 3.896,0.823 5.51,1.208 1.615,0.385 10 false 1 3.49,0.833 4.073,1.188 0.583,0.354 10 false MS5 5.354,0.938 5.938,1.292 0.583,0.354 10 false MS5 4.938,0.948 5.521,1.302 0.583,0.354 10 false G10 5.344,1.365 5.927,1.719 0.583,0.354 10 false SI 3.625,1.375 4.208,1.729 0.583,0.354 10 false SI 3.531,2.073 4.115,2.427 0.583,0.354 10 false SE 4.979,1.458 5.563,1.813 0.583,0.354 10 false G9 4.99,1.281 5.573,1.635 0.583,0.354 10 false 18 4.99,0.76 5.573,1.115 0.583,0.354 10 false 14 0.135,0.073 1.042,0.594 0.906,0.521 12 false w/o ABS:

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, make sure to replace it with a new one.

·

If the vehicle speed is outside the allowable range when tested, perform the operation check.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK



HINT:

Before starting the following inspection, check tire size and tire air pressure.


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ ABS A
w/o ABS B



A

2.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)

B

9.CHECK COMBINATION METER ASSEMBLY
2.CHECK FOR DTC (CAN COMMUNICATION SYSTEM)

Result:
Result Proceed to
OK (w/ VSC) A
OK (w/o VSC) B
NG C



A

3.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)

B

8.CHECK FOR DTC (ANTI-LOCK BRAKE SYSTEM)

C

3.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)

NG

4.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Speed Meter Operation Speedometer
·

OFF, 0, 40, 80, 120, 160 or 200 (km/h) (for km/h)

·

OFF, 0, 40, 80 or 100 (mph) (for mph)


There is a deviation in the values displayed on the speedometer display (Control range → Speedometer)
for km/h (Type A)
·

40 → 41.7 to 46.2

·

80 → 83.4 to 88.4

·

120 → 125.1 to 130.6

·

160 → 166.2 to 173.2

·

180 → 186.9 to 194.5


for km/h (Type B)
·

40 → 41.4 to 45.9

·

80 → 82.7 to 87.7

·

120 → 124.1 to 129.1

·

160 → 165.4 to 170.4


for km/h (Type C)
·

40 → 41.0 to 45.5

·

80 → 82 to 87

·

120 → 123.1 to 128.1

·

160 → 164.1 to 169.1


for km/h (Type D)
·

40 → 40.5 to 45

·

80 → 81 to 86

·

120 → 121.4 to 126.4

·

160 → 161.9 to 166.9


for km/h (Type E)
·

40 → 40.6 to 45.1

·

80 → 81.3 to 86.3

·

120 → 121.9 to 126.9

·

160 → 162.5 to 167.5


for mph
·

40 → 42 to 44.5

·

80 → 83.1 to 87.1


Body Electrical > Combination Meter > Active Test
Tester Display
Speed Meter Operation
50004 122 1
OK:

Speedometer indication is normal.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (VEHICLE SPEED METER)

NG

REPLACE COMBINATION METER ASSEMBLY

5.READ VALUE USING GTS (VEHICLE SPEED METER)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Meter Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed -
Body Electrical > Combination Meter > Data List
Tester Display
Vehicle Speed Meter
50003 122 8
HINT:
·

When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.

·

When the Data List values of the ECUs do not match, a signal output error of the brake actuator assembly (skid control ECU) or an internal malfunction of the combination meter assembly is suspected.



OK:

Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

6.READ VALUE USING GTS (VEHICLE SPEED)
6.READ VALUE USING GTS (VEHICLE SPEED)
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Normal Condition Reference Value Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Almost the same as actual vehicle speed -
Chassis > ABS/VSC/TRC > Data List
Tester Display
Vehicle Speed
50003 105 42
OK:

Vehicle speed displayed on the GTS is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



Result:
Proceed to
OK
NG



OK

7.CHECK COMBINATION METER ASSEMBLY

NG

7.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly with a new one.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Check that the operation of the speedometer returns to normal.

OK:

The operation of the speedometer returns to normal.



Result:
Proceed to
OK
NG



OK

END (COMBINATION METER ASSEMBLY IS DEFECTIVE)

NG

8.CHECK FOR DTC (ANTI-LOCK BRAKE SYSTEM)
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)

NG

9.CHECK COMBINATION METER ASSEMBLY
a.
E200403C12
1.521,0.26 1.917,0.479 0.396,0.219 1.052,1.125 0.771,0.865 0.771,0.865 0.615,0.865 true 0.406,0.76 0.708,1.073 0.302,0.313 10 false SI 1.625,0.281 1.99,0.469 0.365,0.188 10 false G9 1.333,4.094 1.458,4.24 0.125,0.146 10 false A 2.969,3.51 3.427,3.885 0.458,0.375 10 false GND 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.094,2.448 0.406,2.604 0.313,0.156 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


Remove the combination meter assembly with the connector(s) still connected.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Connect an oscilloscope to terminal G9-18 (SI) and body ground.


c.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection G9-18 (SI) - Body ground
Tool Setting 5 V/DIV, 20 ms./DIV
Vehicle Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by A in the illustration narrows.


OK:

The waveform displayed is as shown in the illustration.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

10.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
10.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the C62 speedometer sensor connector.


b.

Disconnect the G9 and G10 combination meter assembly connectors.


c.

Measure the resistance according to the value (s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C62-1 (MS5) - G10-14 (MS5) Always Below 1 Ω
C62-3 (SI) - G9-18 (SI) Always Below 1 Ω
C62-2 (SE) - Body ground Always Below 1 Ω
C62-1 (MS5) or G10-14 (MS5) - Body ground Always 10 kΩ or higher
C62-3 (SI) or G9-9 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.
E323259C01
1.458,0.333 1.927,0.573 0.469,0.24 0.688,1.052 0.896,1.052 0.896,1.052 1.313,1.354 true 0.198,0.188 0.51,0.344 0.313,0.156 10 false *a 1.563,0.354 1.875,0.51 0.313,0.156 10 false C62 0.375,0.958 0.833,1.302 0.458,0.344 10 false MS5
*a Front view of wire harness connector
(to Speedometer Sensor)


Disconnect the speedometer sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C62-1 (MS5) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY