Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM
RM3250E _51 Engine / Hybrid System _037990 1KD-FTV ENGINE CONTROL _0184269 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0500  Vehicle Speed Sensor  


DESCRIPTION

Vehicles which are equipped with a manual transmission detect the vehicle speed using the speed sensor. The speed sensor transmits a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. The 4-pulse signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter. The signal is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of the pulse signal.

A115899E46
0.594,1.042 1.479,1.438 0.885,0.396 10 false from Wheel Speed Sensor 1.792,1.958 3.01,2.208 1.219,0.25 10 false Skid Control ECU 3.469,1.958 5.344,2.208 1.875,0.25 10 false Combination Meter Assembly 3.115,0.604 3.698,0.813 0.583,0.208 10 false 4-Pulse 5.042,0.604 5.667,0.823 0.625,0.219 10 false 4-Pulse 6.042,1.323 6.448,1.521 0.406,0.198 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A" Conditions (a), (b) and (c) are met for 8 seconds or more (2 trip detection logic):
(a) Engine coolant temperature is higher than 70°C (158°F).
(b) Injection volume is 29.73 mm3/st or more.
(c) No speed signal is input to the ECM.
Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):
(a) The fuel-cut operation is being performed.
(b) No speed signal is input to the ECM.
·

Open or short in speedometer circuit

·

Speedometer assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0500 Vehicle Speed

CONFIRMATION DRIVING PATTERN

P0500
DTC Detection Drive Pattern Drive the vehicle at 10 km/h (6.3 mph) or more

WIRING DIAGRAM

A255061E23
0.427,2.094 0.75,2.271 0.323,0.177 10 false G9 0.427,2.24 1.708,2.521 1.281,0.281 10 false Combination Meter 5.927,2.104 6.313,2.292 0.385,0.188 10 false ECM 5.354,0.792 5.688,0.958 0.333,0.167 10 false SPD 5.354,1.469 5.604,1.667 0.25,0.198 10 false E1 1.156,0.875 1.385,1.052 0.229,0.177 10 false +S 5.021,0.885 5.354,1.063 0.333,0.177 10 false G83 5.021,1.49 5.354,1.667 0.333,0.177 10 false C56 5.073,0.667 5.292,0.854 0.219,0.188 10 false 17 1.427,0.99 1.698,1.177 0.271,0.188 10 false 19 5.115,1.292 5.25,1.49 0.135,0.198 10 false 7

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.

HINT:

The vehicle speed sensor is operating normally if the speedometer reading is normal.


OK:

The vehicle speed sensor is operating normally.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (VEHICLE SPEED)

NG

3.CHECK SPEEDOMETER CIRCUIT
2.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Vehicle Speed.

Powertrain > Engine > Data List
Tester Display
Vehicle Speed
50003 234 10

e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

OK:

Vehicle speed displayed on GTS and speedometer display are equal.



Result:
Proceed to
OK
NG



OK

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

4.CHECK HARNESS AND CONNECTOR
3.CHECK SPEEDOMETER CIRCUIT
a.

Check the speedometer circuit.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction

HINT:

Inspect the brake actuator assembly and speed sensor.



Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR
a.
A127854C24
0.208,0.542 0.594,0.802 0.385,0.26 2.99,0.615 2.729,1.323 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.313,0.594 0.625,0.792 0.313,0.198 10 false G9 3.01,0.51 3.323,0.708 0.313,0.198 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the combination meter assembly connector.


Result:
Proceed to
OK
NG



OK

5.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

NG

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
5.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
a.
A205820C23
0.146,0.979 0.521,1.24 0.375,0.26 1.646,0.458 0.885,1.115 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.24,1.031 0.552,1.229 0.313,0.198 10 false G9 1.688,0.375 2.229,0.573 0.542,0.198 10 false 19 (+S) 2.885,3.583 3.198,3.781 0.313,0.198 10 false GND
*a Component with harness connected
(Combination Meter Assembly)


Move the shift lever to neutral.


b.

Jack up the vehicle.


c.

Check the voltage between the terminal of the combination meter assembly and the body ground while a wheel is turned slowly.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-19 (+S) - Body ground Ignition switch ON Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

8.REPLACE COMBINATION METER ASSEMBLY
6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-19 (+S) - G83-17 (SPD) Always Below 1 Ω
G9-19 (+S) or G83-17 (SPD) - Body ground Always 10 kΩ or higher



d.

Reconnect the combination meter assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 234

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at 10 km/h (6.3 mph) or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

g.

Confirm that the pending DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END