Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM3250E _58 Vehicle Interior _038073 HEATING / AIR CONDITIONING _0184341 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1412/12  Ambient Temperature Sensor Circuit  


DESCRIPTION

The thermistor assembly (ambient temperature sensor) is installed in front of the cooler condenser assembly to detect the ambient temperature which is used to control the air conditioning system AUTO mode. This sensor is connected to the combination meter assembly and detects fluctuations in the ambient temperature. This data is used for controlling the cabin temperature. The sensor sends a signal to the air conditioning amplifier assembly via the combination meter assembly. The resistance of the thermistor assembly (ambient temperature sensor) changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. Conversely, as the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies a voltage (5 V) to the thermistor assembly (ambient temperature sensor) and reads voltage changes due to changes in the resistance of the thermistor assembly (ambient temperature sensor).

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1412/12 Ambient Temperature Sensor Circuit
·

Diagnosis condition: None

·

Malfunction state: Open or short in thermistor assembly (ambient temperature sensor) circuit

·

Malfunction Period: None (as present malfunction), memorized (4 seconds or more) (as past malfunction)


·

CAN communication system

·

Thermistor assembly (ambient temperature sensor)

·

Harness and connector

·

Air conditioning amplifier assembly

·

Combination meter assembly


Memorized (4 seconds or more) -

HINT:
·

The air conditioning amplifier assembly stores the DTC of the respective malfunction if it has occurred for the period of time indicated in the parentheses.

·

If the ambient temperature is approximately -52.9°C (-63.22°F) or less, DTC B1412/12 may be output even though the system is normal.



WIRING DIAGRAM

E316651E02
5.948,0.656 6.406,0.854 0.458,0.198 10 false TX+ 5.958,0.865 6.417,1.063 0.458,0.198 10 false TX- 5.521,1.521 5.979,1.719 0.458,0.198 10 false G33 5.552,1.698 7.104,2.281 1.552,0.583 10 false Air Conditioning Amplifier Assembly 3.229,1.625 3.688,1.823 0.458,0.198 10 false G9 3.229,1.781 5.656,2.042 2.427,0.26 10 false Combination Meter Assembly 4.708,0.646 5.167,0.844 0.458,0.198 10 false CANH 4.729,0.844 5.188,1.042 0.458,0.198 10 false CANL 4.385,0.635 4.844,0.833 0.458,0.198 10 false AD 3.979,0.188 4.438,0.385 0.458,0.198 10 false 5 V 3.063,0.521 3.521,0.719 0.458,0.198 10 false TX1+ 3.073,1 3.531,1.198 0.458,0.198 10 false TX1- 2.792,0.521 3.25,0.719 0.458,0.198 10 false 33 2.802,1 3.26,1.198 0.458,0.198 10 false 34 1.792,0.51 2.25,0.708 0.458,0.198 10 false 2 1.781,1 2.24,1.198 0.458,0.198 10 false 1 1.542,0.51 2,0.708 0.458,0.198 10 false + 1.542,0.99 2,1.188 0.458,0.198 10 false - 0.188,1.479 0.646,1.677 0.458,0.198 10 false A43 0.177,1.646 2.125,2.135 1.948,0.49 10 false Thermistor Assembly (Ambient Temperature Sensor) 0.573,2.427 3,2.688 2.427,0.26 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When the servo motor or air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS (AMBIENT TEMP SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Ambient Temp Sensor Thermistor assembly (ambient temperature sensor) Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature displayed Thermistor assembly (ambient temperature sensor) system malfunction:
·

When open circuit: -23.30°C (-9.94°F)

·

When short circuit: 65.95°C (150.71°F)


Body Electrical > Air Conditioner > Data List
Tester Display
Ambient Temp Sensor
50003 121 2
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
NG C



A

REPLACE COMBINATION METER ASSEMBLY

B

C

2.INSPECT THERMISTOR ASSEMBLY (AMBIENT TEMPERATURE SENSOR)
2.INSPECT THERMISTOR ASSEMBLY (AMBIENT TEMPERATURE SENSOR)


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY [AMBIENT TEMPERATURE SENSOR] - COMBINATION METER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY [AMBIENT TEMPERATURE SENSOR] - COMBINATION METER ASSEMBLY)
a.

Disconnect the A43 thermistor assembly (ambient temperature sensor) connector.


b.

Disconnect the G9 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-2 (+) - G9-33 (TX1+) Always Below 1 Ω
A43-1 (-) - G9-34 (TX1-) Always Below 1 Ω
A43-1 (-) - A43-2 (+) Always 10 kΩ or higher
A43-2 (+) or G9-33 (TX1+) - Body ground Always 10 kΩ or higher
A43-1 (-) or G9-34 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL

HINT:

Since the combination meter assembly cannot be inspected while it is removed from the vehicle, replace the combination meter assembly with a normal one and check that the condition returns to normal.




c.

Check for DTCs when the following conditions are met using the GTS or performing the panel diagnosis (sensor check).

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DTC CHECK / CLEAR

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DIAGNOSIS SYSTEM

Body Electrical > Air Conditioner > Trouble Codes
50001 121
OK:

DTC B1412/12 is not output.



Result:
Proceed to
OK
NG



OK

END (COMBINATION METER ASSEMBLY IS NOT NORMAL)

NG